Linksys Wireless Router :: WRT120N LAN Port 1 Flashing But Not Connected To Physical Port
Jun 24, 2012
I've been using a WRT120N on a local area connection.The WRT120N acts as a gateway and also to connect to the PPOE connection, via a bridged adsl modem.I've noticed that the LAN port 1 was flashing although the network cable was disconnected from the physical port. I've restarted a few times but to no avail as well. Ever since that, I've noticed that connection through cable are unstable and hard.Now, I'm not able to reset or upgrade the router's firmware.Is there any other way to be done so that I can get this router working as normal again.
View 6 Replies
ADVERTISEMENT
Aug 23, 2012
My EA4500 is not working. The power indicator light is on but the green and yellow lights on the Internet port are not flashing and the modem the EA4500 is connected to show no activity on that port. Also, the EA4500 is not broadcasting so I can't even connect to it to use Cisco Connect to troubleshoot. I tried resetting it but it did nothing. This has happened before but is usally fixed with a reset.
View 8 Replies
View Related
Jan 2, 2013
Several days ago there was a huge storm, and I think a thunder burned the WAN port of my linksys wrt120n router. Everything else is working good, I can detect the local network but I don't have internet. My internet connection is also working good. My question is, do I have a possibility to use some of LAN port like a WAN? I'm only using 2 of 4 LAN ports. It would be very useful because it's a pity to buy another router just for a not working WAN port.
View 3 Replies
View Related
Nov 2, 2012
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies
View Related
Nov 1, 2009
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
View 9 Replies
View Related
Sep 2, 2011
I need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.
View 1 Replies
View Related
Dec 16, 2011
I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies
View Related
Dec 2, 2011
I was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
View 4 Replies
View Related
Jan 14, 2012
If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?
View 5 Replies
View Related
Jul 3, 2012
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies
View Related
Nov 21, 2012
I want to use Qos in EA2700. I want to know whether the port in the Qos means the port of local computer or the port of server. Or is it a source port or a destination port?
View 3 Replies
View Related
Mar 28, 2012
I created a wlan just for our wireless IP phones.I assigned an interface I created which in turn was set to a specific port on company 2504 WLC. Connecting switchport is set to trunk. Right now I can't ping the voice wlan interface.
View 1 Replies
View Related
Sep 7, 2011
I have a Linksys WRT120N that I use at home for wireless connectivity, with a total of three laptops that connect wirelessly, plus my Samsung Intercept phone. It's a mixed Wireless G and N network; the laptops run Windows XP, Windows Vista and Windows 7.The issue I'm having is this: the computers and phone do not stay connected on this network. Here's a for instance:Monday: I am able to connect wirelessly to my network with my laptop.Tuesday: I cannot connect to the same network; repairing the connection does nothing.Now substitute my laptop for the one running Windows 7, or Vista, or my phone.At that point, I have to power the router down and power it back on, and then we're back in business. The router currently is running version 1.0.05 of the firmware.
View 3 Replies
View Related
Jan 27, 2012
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 1 Replies
View Related
Aug 11, 2010
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 5 Replies
View Related
Jan 6, 2012
I have a Linksys WRT120N with two desktops connected via wired connections.In the house, there are two students accessing the Internet through WiFi via the WRT120N.One of the laptops (on an Apple laptop) seems to lose its' connection from time to time.The other laptop (Lenovo) is located the furthest distance from the router and only gets two bars signal strength.Would my best option to improve the signal strength for the Lenovo laptop and hopefully, also increase reliability for the Apple laptop be to purchase a new router such as a Linksys E1500 with speed boost or would it be best to try a Linksys range extender (RE1000)?
View 2 Replies
View Related
Nov 21, 2011
Can I configure two voice vlans on the same physical port?
View 2 Replies
View Related
Nov 13, 2012
Firewall: ASA 5510
Switch: Linksys SRW2048
Physical topology: PC - > VLAN99 - > SRW2048 - trunk - > ASA5510
Switch Setup:
I've been tasked with breaking up a network that has run out of IP's, and have decided to use VLANs to accomplish this. I have to use an ASA5510 to accomplish all the routing between hosts in different VLANs.Port 48 is trunked to the ASA eth0/0 interface, with VLAN 99 and VLAN 20 tagging packets, VLAN 1 Untagged. Hosts hooked up to appropriate ports on Switch.
View 2 Replies
View Related
Nov 7, 2011
I am learning the 2911 router. Is there a way to set a physical single RJ45 port to handle multiple WAN IPs? Or do I need to buy a port expansion module.
View 12 Replies
View Related
Apr 2, 2013
We have currently a WLC 5508 using 8 ports bundled into an etherchannel.
We would like to remove one physical from this etherchannel and use it for providing an access to Internet only,
Is it possible to create an virtual interface on the WLC that points only on this port?
(we would like to have a physical separation for the Internet traffic only and encrypt the capwapp up to the WLC).
View 10 Replies
View Related
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Oct 30, 2011
I have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies
View Related
Feb 28, 2012
What are the pros and cons of configuring a Switch Virtual Interface (SVI) versus a routed physical port between layer 3 switches?For example, if I have two 4506s and have a need to run HSRP and route between them which feature is better and why?
switch_a
!
interface vlan 25
ip address 10.10.10.1 255.255.255.0
!
interface fa0/1
switchport mode trunk
[code].....
View 1 Replies
View Related
Jan 12, 2012
how to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
3750 Config:
interface Port-channel2
!
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100
[code]....
Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.
View 7 Replies
View Related
Jan 4, 2013
My customer wants each ACE4710 (of a highly available cluster) to have its own, dedicated port for management purposes.
According to documentation, IP addressing can be applied to VLAN interfaces, so in order to satisfy the requirement, I should make one port belong to an "access VLAN X", and then apply IP addressing to the corresponding "interface VLAN X". This should satisfy my customer´s requirement in an indirect way.
But... ¿ Can´t I just configure IP address on one of the 4 ethernet ports in order to save the work of building the aforementioned VLAN? I am asking this since I do not have access to a real box in order to verify.
View 2 Replies
View Related
Nov 14, 2012
What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies
View Related
Jul 9, 2012
I've Nexus 7010 switch installed in my DC. I've conncected Cisco router to one of the Ports. On the same port I'm getting following error message and hence, unable to form EIGRP neighborship.
DR-CORE-SW-S01-NEXUS7K %MODULE-2-MOD_SOMEPORTS_FAILED:
Module 1 (serial: JAF*******NGK) reported failure on ports 1/2-1/2 (Ethernet) due
to R2D2 : Speed patch failed - no frames transmitted in device 143 (error 0xc8f0
1273)
View 1 Replies
View Related
May 10, 2012
I need to have some (maybe four) virtual network interfaces, one face of them connected to my laptop and another face bridged to one of my physical network interfaces.How can i do that?Ive tried VirtNet and Microsoft Loopback Adapter but no success.
View 1 Replies
View Related
Aug 30, 2012
During an installation, we plugged a Ruckus wireless bridge (powered by a PoE injector) into G0/0 on the 1941. The port status remained down/down. We then tried connecting it to G0/1. Again, the port status remained down/down. We took another wireless bridge, plugged it into G0/0 and the port changed to up/up status within a few seconds. The same happened when connected to G0/1. Both ports are have speed/duplex set to auto/auto.We took the cable from the first wireless bridge and connected it a 3550 switch, the FastEthernet port went up/up. We then took the cable and connected it to a switchport card (HWIC-4ESW) that was installed in the 1941 router. The port came up/up.We connected to wireless bridge back to G0/0 in the 1941 and manually set the speed/duplex to 1000/full. The link light on the router became illuminated after a few seconds but no console message was displayed (nor did any events appear in the log) and a "show int g0/0" showed the port status as down/down. This was could not be duplicated as this only happened one time The wireless bridges sit atop of a water tower and are connected each via a shielded ethernet cable. The cable that we're having trouble with is cat5e STP and about 310feet in length. I should note that we have not yet swapped the PoE injector but it seams to be functioning properly as power is getting to the wireless bridge and its accessible. Also because if the wireless bridge for some reason didn't come back up after a power cycle it would potentially mean climbing the tower to perform a hard reset. We tried another 1941 with same results however we have not tried another router model to rule out a potential platform issue. Can you recommend any troubleshooting steps to determine why the port status of the gig interfaces on the 1941 don't come up?
View 4 Replies
View Related
Jul 16, 2011
I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
View 1 Replies
View Related
Sep 28, 2011
I want to setup wireless on laptop with USB Stick connected to usb port.
View 2 Replies
View Related
Sep 21, 2011
how to enable protection path in GSR 12404 router Gigi interface connected to mux port. Like we configure APS group for POS interfaces.
View 1 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
