Cisco WAN :: No Link On 1941 Router When Connected To Routed Port?
Aug 30, 2012
During an installation, we plugged a Ruckus wireless bridge (powered by a PoE injector) into G0/0 on the 1941. The port status remained down/down. We then tried connecting it to G0/1. Again, the port status remained down/down. We took another wireless bridge, plugged it into G0/0 and the port changed to up/up status within a few seconds. The same happened when connected to G0/1. Both ports are have speed/duplex set to auto/auto.We took the cable from the first wireless bridge and connected it a 3550 switch, the FastEthernet port went up/up. We then took the cable and connected it to a switchport card (HWIC-4ESW) that was installed in the 1941 router. The port came up/up.We connected to wireless bridge back to G0/0 in the 1941 and manually set the speed/duplex to 1000/full. The link light on the router became illuminated after a few seconds but no console message was displayed (nor did any events appear in the log) and a "show int g0/0" showed the port status as down/down. This was could not be duplicated as this only happened one time The wireless bridges sit atop of a water tower and are connected each via a shielded ethernet cable. The cable that we're having trouble with is cat5e STP and about 310feet in length. I should note that we have not yet swapped the PoE injector but it seams to be functioning properly as power is getting to the wireless bridge and its accessible. Also because if the wireless bridge for some reason didn't come back up after a power cycle it would potentially mean climbing the tower to perform a hard reset. We tried another 1941 with same results however we have not tried another router model to rule out a potential platform issue. Can you recommend any troubleshooting steps to determine why the port status of the gig interfaces on the 1941 don't come up?
View 4 Replies
ADVERTISEMENT
May 25, 2013
I have made a routed port on 3560G Switch and defined a pool 172.28.4.62 255.255.255.192 and connected to E1 converter RAD (4E1 to 4 FE) the E1 media is through Microwave on the other end same E1 converter is connected through layer 2 switch and defined a pool as of routed port configured in 3560G switch.
The port is generating lot of giants and after a while it also distrubs other routes ( Port1 to Port 16), configured with Vlan11 and port 22 as routed port.I have checked the routed port through wireshark the maximum frame size is 1514 and configured the MTU to 1514, giants are not showing any more but after 10 to 12 hours switch gets hang. Either to shut the port or to reload the switch to get switch and other layer routes to be normal.
I have checked speed and duplex settings same as E1 converter. Full duplex. 100 Speed. Why switch is not behaving normal. If I shutdown the routed port it is normal.
1. interface GigabitEthernet0/22
no switchport
ip address 172.28.4.62 255.255.255.192
flowcontrol receive on
end
[code]....
View 5 Replies
View Related
Feb 13, 2013
I have some questions about how to configure my Cisco 1941 with a routed subnet from my ISP to forward them to 1 or more servers in my LAN.1 Routed subnet /29 from my ISP (over a fiber connection).In my LAN I have (at the moment) 3 servers, and about 15 clients.I would like to use the first ip address from the routed subnet for internet traffic from all the clients in the LAN.I would like to use the second ip address from the routed subnet for server1 so that server1 accept some allowed connections and that server1 connects to the internet with the second ip address from the routed subnet
I would like to use the thirth ip address from the routed subnet for server2 so that server2 accept some allowed connections and that server2 connects to the internet with the thirth ip address from the routed subnet.I would like to use the fourth ip address from the routed subnet for server3 so that server3 accept some allowed connections and that server3 connects to the internet with the fourth ip address from the routed subnet.[code]
View 13 Replies
View Related
Jan 7, 2012
I would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0.0.0/24) How can I forward different ports to this 3 different private networks with an E2500.Under "Games&Applications" in the" Portforwarding" menu the first 3 octets of the "to IP-address" are fix and corresponds ever with the LAN ip address of th E2500.
View 4 Replies
View Related
Dec 20, 2011
I have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
View 7 Replies
View Related
Aug 29, 2012
I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies
View Related
May 23, 2013
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies
View Related
Feb 29, 2012
I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
Apr 20, 2012
I have an old Nortel network with a bunch of servers attached. Connected to it is the new Cisco core, by way of a routed port. My task is to migrate servers over to the Cisco side of the network, with minimal downtime, and have full network connectivity, retain IP addresses/remain on the same subnet, and retire the Nortels. The Nortels are running VRRP, so I can fail the gateway over by becoming part of that group and later dropping the Nortels, but I can't seem to get a host on the Cisco side to participate in the original subnet. The routed port kills VLAN traffic, so I tried bridging the VLAN with the routed port, to no avail.
View 7 Replies
View Related
Jan 12, 2012
Wan goes down when transferring files between pcs connected to the lan port.It looks like it's running out of resources or something. Passing more than 10GB of data to other pc is a pain in the ass because nobody else can access internet (lan and wireless clients).Filled a support request in local dlink site. No response so far.
Model Dir-600 B2
Firmware 2.05
2 pcs transferring lan data.3rd pc (doing nothing) can't access router config at 192.168.0.1.
View 9 Replies
View Related
Oct 28, 2011
is there any way to interact with wan port like LAN?i have connected a rocket m5 as a bridge to my Dir-615 wan port but i cant see the AirOS login page (rocket m5 configuration page) nor brige's ip address on my LAN...is there any way to interact with the ip address that connected to wan port?
View 1 Replies
View Related
Apr 29, 2012
I am facing low relaiblity issue in one of the ethernet port even no link is connected to that port.
Router model : cisco 3660
IOS - c3660-ik8s-mz.122-24a.bin
Ethernet1/2 is up, line protocol is down
Hardware is AmdP2, address is 0007.85fb.c312 (bia 0007.85fb.c312)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
[Code]...
View 2 Replies
View Related
Mar 14, 2012
We are looking for a solution that to use Sub-interface on a routed port on 6509, instead of using a SVI on it.Are there any different when using Sub-interface?
View 3 Replies
View Related
Jun 24, 2012
I've been using a WRT120N on a local area connection.The WRT120N acts as a gateway and also to connect to the PPOE connection, via a bridged adsl modem.I've noticed that the LAN port 1 was flashing although the network cable was disconnected from the physical port. I've restarted a few times but to no avail as well. Ever since that, I've noticed that connection through cable are unstable and hard.Now, I'm not able to reset or upgrade the router's firmware.Is there any other way to be done so that I can get this router working as normal again.
View 6 Replies
View Related
Dec 20, 2010
We have a 6509 that was connected to 2 other locations(location A and B) and our local lan (location MAIN). We wanted to move the location A and B to a 3750 switch and only allow the traffic that needed to access our location MAIN to come through the firewall. The only problem I ran into is that before location A and B were on different interfaces so in the 6509 firewall the routes for traffic to our MAIN location was done by static routes.
I.E.
static (MAIN_intf,A_intf) 192.1.1.72 10.94.10.72 netmask 255.255.255.255 0 0
static (MAIN_intf,B_intf) 192.2.2.72 10.94.10.72 netmask 255.255.255.255 0 0
[Code]....
because it has a static overlap, which makes sense to me, but my question is how do I configure the network to get this to work? Do I have to reconfigure my network and access-list? Do I need to add more ports between the 6509 and 3750? I'm not sure if this is the best way to do what we want. If something is not clear I'll try my best to explain the setup, but I just took over for our I.T. guy when he left.
I put 10.10.10.72 instead I should have put 10.94.10.72. the routed port is on a different subnet than the computer I'm trying to access.
View 4 Replies
View Related
Apr 12, 2013
Actually i have 7600 router and all trafic passes through Gi0/1(Routed port) interface to 6500 series switch. I need to create a vlan on this router eg. vlan 10 Any how it is possible assign a vlan to routed port and traffic of wan interfaces and the vlan traffic passed together.
View 2 Replies
View Related
Feb 14, 2013
I have the DIR-655, Rev. B running 2.07NA firmware, and have a strange problem with my wired clients. I have my primary computer/desktop PC connected via wired connection. I also have several wireless clients (laptop, iPad, iPhones, etc.). All have been performing normally. However, in December I connected a wired weather internet bridge to another ethernet port on the DIR-655.
It functions as it is supposed to, and all other connected devices do as well. But here's the problem - whenever I use the desktop PC (the only other wired connection) to do anything on the internet (mostly just web browsing ... I don't stream media from the internet on it, I don't do torrents....nothing out of the ordinary, and nothing really of high bandwidth), the wired weather bridge cannot communicate with its associated website. This continues as long as I'm using the desktop PC. When I stop using the desktop, the weather bridge resumes normally.
I have researched the weather bridge, and it is simply doing POST transactions (or so I'm told) to the website listening to it. It doesn't wait for acknowledgements or anything...just keeps POSTing updates. I tried reserving an IP for the weather bridge and the desktop, enabling QoS, and prioritizing the weather bridge (100 vs. desktop at 125), but it didn't work. I've tried moving the weather bridge into the DMZ. I'm totally baffled how just using the desktop to browse the internet could completely block the traffic from the weather bridge.
On the weather bridge support site, they suggested that I insure I'm not connected in gigabit speeds from my computer to the router, because in the past that has been known to cause issues on clients not running that speed, but I don't think my desktop is connected in that fashion. According to the settings, it can do 10 or 100, full or half. I have it set to AUTO.
View 3 Replies
View Related
Apr 26, 2013
I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies
View Related
Nov 15, 2012
What should the duplex mode to be set on a routed port gi0/21 that are running HSRP ? I try setting the gi0/21 to full, but it caused the port to be down. The only way for the port to be up is setting it to half duplex.
Cisco 3750 Switch
==============
interface GigabitEthernet0/21
no switchport
ip address 10.200.104.34 255.255.255.248
[Code].....
View 2 Replies
View Related
Jan 5, 2012
I would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0. 0.0/24)How can I forward different ports to this 3 different private networks with an E2500.In the "Games&Applications" Menu are the first 3 octets of the "to IP-address" are fix and corresponds with the LAN ip address.
View 3 Replies
View Related
Feb 28, 2012
What are the pros and cons of configuring a Switch Virtual Interface (SVI) versus a routed physical port between layer 3 switches?For example, if I have two 4506s and have a need to run HSRP and route between them which feature is better and why?
switch_a
!
interface vlan 25
ip address 10.10.10.1 255.255.255.0
!
interface fa0/1
switchport mode trunk
[code].....
View 1 Replies
View Related
Jul 7, 2012
How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
View 4 Replies
View Related
Jul 1, 2011
I have a LAN with Cisco 1941 as the only router with NAT that connects it to the internet, with a single public IP. There are many gamer users, and they complain that Call of Duty Modern Warfare 2 sees our network as "strict NAT", while for full gaming experience it needs "open NAT". After a small research I have found out that CoD needs certain port ranges to be forwarded to LAN IPs. Well, I know how to forward a range of ports to a single IP, but how is it possible to forward a port range for all the IPs in the LAN?
View 1 Replies
View Related
Jan 2, 2012
I am looking to add a new DMZ zone to our network with have a standard 1941 (1x LAN / 1 x WAN port) and so I need a 3rd routable L3 interface to create the DMZ.
Is the HWIC-1FE what I am looking for or is there another way to do this?
View 12 Replies
View Related
Apr 18, 2012
I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
View 10 Replies
View Related
Dec 5, 2011
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies
View Related
Nov 16, 2012
One of branch locations has a Cisco 1941 Router . The port details are as follows
-Gi0/0 - ISP line
-Gi0/1 - Inside Network ( To a 2960 Switch)
Now they have procurred another line from ISP through which MPLS based VPN to the Main location is configured. What are the options I have , to terminate it on the Router ? As all the On board LAN ports are filled I guess I wont be able to do anything with the current setup .Are Switching modules available ? What is the Embedded-Service-Engine0/0 port that I see on #sh ip int b output ?
View 4 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
Oct 30, 2011
I have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies
View Related
Sep 2, 2011
I need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.
View 1 Replies
View Related
Jul 1, 2012
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
View 2 Replies
View Related
Dec 16, 2011
I'm trying to connect an Epson Stylus Color 740 USB printer to a newly purchased E4200 wireless router. I've upgraded to the latest Cisco Connect software and to version 1.0.0.3 router firmware. I get the message "A non-supported device is connected to your router's USB port. Disconnect that device and follow the steps below to connect a USB printer to your router." Cisco support was not beneficial.
View 1 Replies
View Related
