Cisco Switching/Routing :: 1941 Upgrade With 4 Port POE Switch Requirements?
Dec 5, 2011
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies
ADVERTISEMENT
Dec 20, 2011
I have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
View 7 Replies
View Related
May 23, 2013
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies
View Related
Feb 29, 2012
I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies
View Related
Jul 1, 2012
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
View 2 Replies
View Related
Jan 14, 2013
We are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
View 3 Replies
View Related
Aug 29, 2012
I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies
View Related
Nov 16, 2012
One of branch locations has a Cisco 1941 Router . The port details are as follows
-Gi0/0 - ISP line
-Gi0/1 - Inside Network ( To a 2960 Switch)
Now they have procurred another line from ISP through which MPLS based VPN to the Main location is configured. What are the options I have , to terminate it on the Router ? As all the On board LAN ports are filled I guess I wont be able to do anything with the current setup .Are Switching modules available ? What is the Embedded-Service-Engine0/0 port that I see on #sh ip int b output ?
View 4 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Jun 26, 2012
I have a few 24-port Cisco 2960G Switches (model WS-C2960G-24TC-L) that I upgraded to IOS Release 15.0(1)SE2 using the web interface. I am now trying to upgrade those switches with the new release, 15.0(1)SE3, however I seem unable to do it, I have tried this on two switches so far, both have been upgraded to SE2 just a couple months ago or so, and both of them will not accept the SE3 upgrade, basically, I can select the tar file in the web browser and click "Upgrade" but when I do the status never changes from "Loading the tar file to the switch". I have tried multiple times from multiple computers using many different web browsers, including IE6 which is listed as supported. I have let it go for as long as 1.5 hours but to no avail.I also had a few idential switches here that had never been upgarded to SE2, I have had no problems loading SE3 onto them using the same method so it would seem that the tar file I have downloaded is valid.
View 5 Replies
View Related
Dec 11, 2012
We have a Cat2960-S Series PoE+ currently running 12.2(55) SE5 ios with SW image C2960S-UNIVERSALK9-M.We want to upgrade the ios to the lastest version but found there are 2 version: 12.2(53) SE2 and 15.0(1) SE.Which is the best & suitable for upgrade?
View 3 Replies
View Related
Oct 31, 2012
I wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies
View Related
Apr 18, 2012
I was just curious about something with upgrading a 2960s stack.
To copy the image to the switches in the stack I use: Switch# archive download-sw tftp://x.x.x.x/filename
Does this also set the image as the boot image or do I still need to issue the boot system flash command?
can I just issue this command on the master switch and reload and the new config will be pushed to the rest of the switches?
View 5 Replies
View Related
Feb 14, 2012
i am trying to upgrade the firmware in my C2960 switch to 15(1) SE2, and i get the error:Failed to execute the command archive download -sw /overwrite /http iosFile
View 2 Replies
View Related
Feb 21, 2012
We have two 3560G-TS-E running 12.2(35)se2, configured as HSRP. Both are running ntp config "ntp peer 210.72.145.44" and it's pretty well that they get the correct time. Yesterday I upgraded the second device to IOS 12.2(58)se2 and ntp doesn't work now. I checked doc that 12.2(58)se2 runs ntp default version 4 so I change to "ntp peer 210.72.145.44 version 3" but still not work. I put here "show ntp" result for different IOS.
IOS 12.2(35)
SW01>show ntp status
Clock is synchronized, stratum 2, reference is 210.72.145.44
nominal freq is 119.2092 Hz, actual freq is 119.2022 Hz, precision is 2**18
reference time is D2EF12A5.2EB2DCB2 (15:07:17.182 GMT Wed Feb 22 2012)
clock offset is -4.6616 msec, root delay is 57.50 msec
[code]...
View 10 Replies
View Related
Jun 4, 2013
I have a 3550 switch right now, and need to upgrade to a gigabit switch, so I'm looking at a 3560G-48. For some reason I purchased an EMI version of my 3550, but run the ipbase image...what I need to look for - is a 3560G-48-s good for what I need?
View 4 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Jan 8, 2013
I am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
View 14 Replies
View Related
Oct 4, 2012
I have upgraded my 3750X switch from
c3750e-universalk9-mz.122-53.SE3
c3750e-universalk9-mz.122-55.SE5.bin
later that by mistake i typed delete /force /recursive flash:now, I am unable to load new IOS error loading "flash:c3750e-universalk9-mz.122-55.SE5.bin" Interrupt within 5 seconds to abort boot process.Boot process failed...
View 3 Replies
View Related
Jan 21, 2013
I have installed Cisco 2955 Switch which already have x.x.x.x EA12 IOS and I copied x.x.x.x.EA13 into the flash: with intention to have EA13 enabled for IOS. I set the Global config for boot system by 'boot system (no falsh)x.x.EA13;x.x.EA12' but then also no luck and was showing EA12 in 'sh ver'. I then deleted the EA12 IOS and set the 'boot system flash:x.x.EA13'. I also had varified IOS EA13 by 'verify flash:IOS Filename', it verified the IOS.
But when I reloaded my switch, I'm unable to login and its in 'switch:' prompt (ROMmon mode - I believe). I then tried for flash_init, load_helper, dir flash: (showing me EA13 there) and finally boot flash:IOS Image file but no good news here... Output like this
Error loading "flash:IOS Image File EA13" Interrupt within 5 seconds to abort boot process. Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"Interrupt within 5 seconds to abort boot process.
My guessing is that the IOS is corrupted (but its not showing me Error loading Image blabla...) I'm trying with EA14 of 4MB and I have 3 MB free spare and decided to remove EA13 first then through XModem try to upload EA14.
Any useful way and recommend me deleting EA13 and upgrading EA14... Also option to set boot image with having two IOS at the same time for permanent use.
View 5 Replies
View Related
May 14, 2013
I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
View 3 Replies
View Related
Jul 8, 2011
Am currently running BT Voyager 2091 wireless ADSL router with BT Voyager 1055 wireless USB adapter. What system requirements does one need to upgrade to 802.11n. The OS is XP Pro x32 bit x86 based PC
View 1 Replies
View Related
Jul 31, 2012
I am trying to upgrade my 2960 edge switch through tftpd...i have configured vlan 1 with IP address 172.16.10.1 and tftpd as 172.16.10.2 I am trying to ping tftpd, but I couldn't, but when I try to ping vlan 1 from tftpd, i can?
View 6 Replies
View Related
Nov 2, 2011
i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?
View 13 Replies
View Related
Dec 8, 2012
I would like to check if it may be possible to hot-upgrade/swap the 4506E power supplies? Based on the configuration guide; I have summarized the steps as follows:
1. Switch has 2 existing power supplies to be upgraded
2. Remove right side/bay 2 power supply and install new power supply
3. At this point; the new power supply will be in err-disabled due to different power supplies on the switch
4. Remove the left side power supply and install new power supply
For item 4; during the removal of the old power supply in bay 1/left side and installation of the new power supply; I am wondering if the switch would lose power even though the new power supply is installed in bay 2?
View 1 Replies
View Related
May 7, 2013
I want to upgrade IOS for my production core 3750 switch. Below is Show version/fash output. I have IOS image "c3750-ipservicesk9-mz.122-55.SE7", need to confirm below concerns:-
1-As this is stackable switch do i need to upgrade on all Switch..i can see there are 3 flash while doing show flash?
2-Is above IOS image support with my switch? do i able to enable ssh?
3-is flash memory is enough to succefully upgrade IOS?
4-Any other point which i should keep in mind before upgrading..any special feature which this IOS wont support.
View 11 Replies
View Related
Jul 29, 2012
I performed an upgraded on a 4948 switch and for some reason the switch kept booting with the old IOS. I was not sure if I needed to change the boot sequence but I performed this upgrade on some of our other 4948's and no issues.I eventually deleted the older IOS version and left the latest version on and reloaded switch and now switch only boots in rommon.I managed to configure the ip info and tftp server ip etc and using the following command as suggested in the rommon help, but it keeps coming back saying 'file not found', when I have checked the file does exist in the tftp server and in the tftpboot folder.
See error message below:
[URL]
Tftp Session details are ....
Filename : /tftpboot/cat4500-ipbase-mz.122-54.SG1
IP Address : 10.250.100.39
Loading from TftpServer: 10.250.150.40
Tftp session failed: File not found
View 4 Replies
View Related
Sep 10, 2012
I have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies
View Related
