Am currently running BT Voyager 2091 wireless ADSL router with BT Voyager 1055 wireless USB adapter. What system requirements does one need to upgrade to 802.11n. The OS is XP Pro x32 bit x86 based PC
View 1 RepliesI need to order LMS for one of our customer with 500 devices and reporting capabilities ..... So i chose base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and Compliance Management - 500 Device License "L-PI-1.1-CM-500"? i tried to search server capability for my requirements & Operating system and couldn't find it .....
1) What is the server requirements ?
2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)
3) Is their any dedicated appliance from Cisco ?
I have a cisco 1941 router. Stock standard vanilla hardware, no extras. Standard universal image. Data and Security not enabled.I would like to add a 4 gigabit port POE switch (EHWIC) module to the router..The 4 port POE switch module will be used to power and connect 2 x Areonet AP's for my home. I'm replacing a Apple Airport Extreeme and Express setup. I'll possibly later use the two remaining POE ports for security cameras.My question is, what extra hardware and or IOS version do I need for the POE swtich module to function on the 1941? [URL] I think this is the model I want EHWIC-4ESG-P #4 port 10/100/1000 Enhanced High-Speed WAN Interface Gigabit Ethernet switch with Power over Ethernet?
View 1 Replies View RelatedWe are planning to replace a few line cards in the existing 6509-E chassis. The sup installed is a VS-S720-10G-3C but the line cards are legacy. As a result we are not able to enable the VSS functionality. We are looking to replace the existing line cards with the following:
1. 1 x WS-X6716-10G-3C
2. 1 x WS-X6724-SFP
3. 4 x WS-X6724-GE-TX
What are the requirements in terms of IOS and Roman.
The current IOS is: Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
And the ROM Version is: ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
Do I need an upgrade?
After upgrade C7609S routers from:c7600rsp72043-adventerprisek9-mz.122-33.SRD4.bin to c7600rsp72043-adventerprisek9-mz.150-1.S3a.bin I lose interface with ip mpls configure form the MRTG SNMP pooling system. cfgmakre not see any more that interfaces (intrefaces fall on ($if_ok) filter). Other interface which not have a ip mpls configured is normally visible in the our MRTG monitoring system. From my site it is looks like that interface when I configure ip mpls go to unknown state for MRTG. That interfaces are not any more ethernet type.I can reach interface with configure ip mpls only with manual configure *.cfg file with ifindex value.
View 0 Replies View Related while upgrade NME-NAM module IOS on 2821, as a result of sudden disorder in power system nam helper image crashed and it seems
i have to fix this !
(as you may know without helper image you cant load IOS image of NAM so it doesn't work !!) on the other hand in Cisco documents it's mentioned besides upgrading NAM IOS we can upgrade helper image too. but i couldn't found in Cisco downloads the appropriate link to download either older version or latest version of , Nam helper image. (even with CCO Account)
in addition i have a brand new NAM Module that contains NAM Helper Image but I couldnt find a way to tranfer this image via ftp to ftp server
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies View RelatedWe have a scheduled office move where we are consolidating 2 remote offices into one. I’ve been asked to spec out the correct size UPS to support all of the network equipment for this new office.I went to the Cisco website and I see on the datasheet for the switches and router where they talk about the wattages and BTU’s but how can I go about deciphering from that information what my total wattage and BTU will be for each switch and router?What numbers should I be looking at? For instance, we have 3 3750 48 port PoE switches. So if I look at the datasheet for that switch they have 4 different columns, one for 100% throughput power consumption, one for 5% throughput, another one for 100% throughput for max PoE load and one for 5% throughput with 50% PoE loads?Is there a common method for deremining UPS requipments? For the switches I pretty sure I need to assume max PoE load in the event every port has a phone plugged into each port.
View 3 Replies View Relatedin LMS (4.1) installing guide, table 'Software and Hardware Requirements for Soft Appliance', it is stated Memory and CPURequirement:
• 4 GB, 2 virtual CPU (< = 500 devices)Host CPU Core clock speed:
• Minimum 2.26 GHz Minimum Virtual CPU Reservations: Number of recommended virtual CPUs x 2.26 GHz:
• 4520 MHz (< = 500 devices)
I have HP server with 6 core CPU 2.0GHz - does it mean it does not meet the minimum system requirements (2.26Ghz)? Will I be able to go pass the installation?
According to the Installation notes for ACS 5.3 we need 500GB of storage for a working installation - if not it defaults to taking 60 GB of disk space for an eval version.
View 1 Replies View Relatedhow to setup 802.1x on the Cisco 500 Series Switches.I have done the whole implamentation in the past with Catalysts and ACS.But would like to see a guide for the 500 series.Do we need the Cisco ACS or can we use RADIUS on Windows?
View 1 Replies View RelatedI am planning to implement SSL-VPN (Any Connect) on an ASR 1002 router running IOS-XE Software Version 15.1(3)S2. I need to use LDAP for user authentication, and need to understand what are RADIUS/ TACACS requirements to use LDAP. Do I need to use Cisco ACS or can I use something like Microsoft IAS or Free Radius?
View 6 Replies View Relatedregarding the power requirements. I have this Cisco 6503-E switch and I need to know what I need in terms of power.
The manual says if using 120VAC, I will need 16A. If using 230VAC, the unit will require 8A.
I have 2 dedicated 20amps circuits both at 120V. Am I correct on plugging each of the power supplies of the cisco unit to each of these circuits?
Another question will be, do I really need to dedicated 2 dedicated 20amps circuits for the unit? Can't I just use one dedicated 20amps circtuis and connect both power supplies to it?
I am reading up on the ACS VMware appliance installation instructions and am a bit confused on the disk space requirements. It says 60Gb is required and then goes on to talk about 500GB for the secondary instance. Do I need more than 60gb? Is the secondary instance a separate machine or part of the same one?URL
View 5 Replies View RelatedI have this that comes up when i go on the networking
View 2 Replies View RelatedWe have a 7604 chassis with the following equipments:
1. RSP720-3C-10GE
2. 7600-SIP-400
3. SPA-1X10GE-L-V2
We would like our SPA to support XFP transceiver having part number XFP-10GZR-OC192LR.
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
What are the VMware requirements to run ACS4.1.4? Im trying to use a VM this as the migration server. According to the cisco docs, it states that: "ACS 4.1 has been tested on the VMWare ESX server with the following configuration:
•VMWare ESX Server 3.0.0
•16 GB of RAM
•AMD Opteron Dual Core processor
•300 GB hard drive
•Four virtual machines
•Windows 2003 Standard Edition
•3 GB of RAM for the guest operating system"
I understand it will work as it "has been tested" with those specs, but the doc does not state the minimum requirements for the virtual machine. I dont want to use/find 300GB of space if I only need 20GB(as an example) to make it work.
I need to choose router for my network. I don't have any special need, besides Internet connection and DHCP for some guest clients.There are around 30 IP phones (static IP), 30 PCs (static IP), and 10 wireless APs (users get dynamic IP). Maximum load is 5 phones, 5 PCs and 20 phones/laptops connected via wi-fi.
I guess I should go for Cisco 800 series. Would model 861 be good or I will need 881 or even 891?
I have a Cisco SG500-52P along with an older SGE-2010P, am I correct that in order to stack they must be the same series?
View 1 Replies View RelatedI was planning to buy 7204 VXR for my site's router for the following requirements:
- support for ATM, Serial, ISDN
- support for 3 10/100/1000 ethernet interface
- support for 2 WAN interface
However, I realized that the 7200 series will not be available for sale after September of this year!! Any "reasonable" replacement for 7204 VXR that meets the above requirements?
To check if this is enough to built point-point MPLS between 2811 abd 3745Maybe some other technology should to be used for point-to-point connection?Basically, there should be transparent connection between routers.Also, it's possible to use ISP routers as MPLS endpoints for MPLS, so seems just etherenet connection required
View 7 Replies View RelatedWe implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies View RelatedI have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies View RelatedAccording to Cisco, one of the ASAs must have an Unrestricted License [URL]:
"On the PIX/ASA Security appliance platform, at least one of the units must have an unrestricted (UR) license. The other unit can have a Failover Only Active-Active (FO_AA) license, or another UR license. Units with a Restricted license cannot be used for failover, and two units with FO_AA licenses cannot be used together as a failover pair."I am unfamiliar with the different ASA licenses, so with my current license, I am unable to enable failover on my two ASAs. Here is a snippet of the "show version" output on one of my ASAs (they are the same as far as licenses go):
Licensed features for this platform:Maximum Physical Interfaces : UnlimitedMaximum VLANs : 250Inside Hosts : UnlimitedFailover : Active/ActiveVPN-DES : EnabledVPN-3DES-AES : EnabledSecurity Contexts : 5GTP/GPRS : DisabledSSL VPN Peers : 10Total VPN Peers : 5000Shared License : DisabledAnyConnect for Mobile : DisabledAnyConnect for Cisco VPN Phone : DisabledAnyConnect Essentials : DisabledAdvanced Endpoint Assessment : DisabledUC Phone Proxy Sessions : 2Total UC Proxy Sessions : 2Botnet Traffic Filter : Disabled
This platform has an ASA 5550 VPN Premium license.
I have the following on my 6509:
Mod Port Model Serial # Versions
---- ---- ------------------ ----------- -------------------------------------
1 10 WS-SVC-WISM-1-K9 XXXXXXXXXXX Hw : 2.2
Fw : 12.2(14r)S5
Sw : 12.2(18)SXF16
Sw1: 8.6(0.306)R3V39
WS-SVC-WISM-1-K9-D XXXXXXXXXXXX Hw : 2.1
There are few documents that tell me different requirements for the WISM cards to configure VSS.
I am trying to copy a new IOS image to a 3825 router. I have verified that there is significantly more free space in flash than is needed to accommodate the image (83 MB free, new IOS is 34 MB). I have also verified that the router has the necessary hardware requirements for the new version of IOS, though it is a moot point with this issue. When I try to copy the image from either TFTPd32 or the Solarwinds TFTP server,the copy gets to about 97% and then shows a mixture of timeouts and out-of-sequence packets (.'s and o's) before telling me the copy job timed out. I have tried bumping both the "timeout" and "max retransmit" on TFTPd32 to 2-3 times their defaults, but it made no difference. The router and my laptop are connected to the same 3550. I have also tried two FTP servers but all I get is "Protocol error" on the router when I try to use either. I see the following in the TFTP debugs: [code]
View 2 Replies View RelatedWe purchased a new monitor to the pc where the router is connected. Since then, my laptop does not connect to the internet. My network is on the list but it says "The settings saved on this computer for network do not match the requirements of the network" and the Connect button is not active.
View 1 Replies View Related I have many of these, many models and versions. I have a WRT54G v1, V1.1, V2....V8, I also have WRT54GS's WRT54GL's and others, Lots of other Linksys stuff, almost all of it in the Blue and Black boxes of varing sizes.I have a heck of a time when I reconfigure my network or the wife changes the furniture. I'd love a single document that lists the power specifications and adapter requirements for thens devices... I can't find them any where on the Linksys site. I Have looked and searched and nowhere can I find a consolidate list.
Any have a list of the DC power Specifications, Barrel sizes, and other stuff needed to buy a replacement Power adapter. This page url...lists a lot of information but does not list this critical information... I am amazed that Linksys does not have it listed some where here. Losing a wall wart should not be a reason to pull you hair out, just a simple purchase, If they don't want to stock them, then at least tell us what they are.
My two devices access the 2.4 ghz wireless network fine on my EA4500.Both my devices, laptop and iPhone4, have N rated network cards. What do I need to use the 5.0 ghz wireless network on the EA4500?Can the iPhone4 use a 5.0 wireless network? When I try to add the 5.0 ghz Wi-Fi to my iPhone4, it cannot find the named but hidden SSID network??
View 2 Replies View RelatedAccording to the note at the bottom of a VMware KB Article "Cisco Nexus 1000V and VMware vCloud Director 1.5,"
"Note: You are must use the Cisco Virtual Network Management Center (VNMC) virtual appliance from Cisco. This is a separate products and needs to be licensed from Cisco."
Is this actually the case? I know you could use portgroup based network pools with vCD 1.0 and 1kv. Can I use the 1kv with VLAN-backed network pools in vCD 1.5 without the Virtual Network Management Center or is it required?
this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
is there any issue in buying air-ap1142n-ek9 802.11A/G/N FIXED AUTO AP INT ANT and later on converting it into lightweight under the control of air-ct2504-15k9 2504 WIRELESS CONTROLLER WITH 15 AP LICENSES ?Are there any requirements on the SW of the WLC and the IOS of the AP? The reason of the choice is budget.
View 1 Replies View Related