Cisco :: C7609S / Lose Interfaces From MRTG Monitor System After Upgrade?
Oct 10, 2011
After upgrade C7609S routers from:c7600rsp72043-adventerprisek9-mz.122-33.SRD4.bin to c7600rsp72043-adventerprisek9-mz.150-1.S3a.bin I lose interface with ip mpls configure form the MRTG SNMP pooling system. cfgmakre not see any more that interfaces (intrefaces fall on ($if_ok) filter). Other interface which not have a ip mpls configured is normally visible in the our MRTG monitoring system. From my site it is looks like that interface when I configure ip mpls go to unknown state for MRTG. That interfaces are not any more ethernet type.I can reach interface with configure ip mpls only with manual configure *.cfg file with ifindex value.
View 0 Replies
ADVERTISEMENT
Jan 24, 2013
I want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
View 2 Replies
View Related
Feb 2, 2012
I have been using a Linksys E3000 router for a few months now. Love it. But this last week, when ever I wake my monitor up after it's power saving mode kicks in, I lose my internet connection for about 15 seconds. If you look at the router before the monitor is on, I am connected. The light is on for port 1. But as soon as my monitor gets turned back on, it light just turns off and will reconnect after about 15 seconds. I've looked it up online and can only find things about when the entire system wakes up, and usually those people have to reboot their entire system to get a connection again, or turn the router off then back on. Using Windows 7?
View 4 Replies
View Related
Jan 22, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : UPC Hungary Ltd.
I can't able to recognize a system - all wifi clients lose connection. When this happens, the ping answer time rech the ~2000 times, then totally lose the connection, the SSID is dissapear - checking with my phone (android - wifi analyzer) and TL-WN822N USB wifi adapter (with the inSSIDer application). Meanwhile the cable clients and the WAN connections works fine, didn't experience anything.If I restart the wifi service with the hardware on/off button, it runs well for some time.This problem appeared when I used the two older official firmware too.
I tried the auto-chanel function width auto channel width, tried to manually set up one of the less interfered channels with both 20MHz and 40MHz channel width, but none of them bring the solution.The intresting thing is, if I change the router with an old D-Link DI-604, the signal is weak, but the wifi connection is stable, with the same TL-WN822N adapter.I tried to guarantee the router, but after two weeks, my reseller said, it looks ok, they - at the TP-Link service - didn't find anything.
View 7 Replies
View Related
May 17, 2011
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies
View Related
Jul 8, 2011
Am currently running BT Voyager 2091 wireless ADSL router with BT Voyager 1055 wireless USB adapter. What system requirements does one need to upgrade to 802.11n. The OS is XP Pro x32 bit x86 based PC
View 1 Replies
View Related
Jul 29, 2012
I am using Cisco ASA5510 Firewall in my network. Upgraded the Memory and Flash to 1GB and 512MB.But the 5 interfaces ports are 10mbps.Can it possible to upgrade the module of Interfaceses from 10mb to 1gb?
View 2 Replies
View Related
Feb 15, 2013
while upgrade NME-NAM module IOS on 2821, as a result of sudden disorder in power system nam helper image crashed and it seems
i have to fix this !
(as you may know without helper image you cant load IOS image of NAM so it doesn't work !!) on the other hand in Cisco documents it's mentioned besides upgrading NAM IOS we can upgrade helper image too. but i couldn't found in Cisco downloads the appropriate link to download either older version or latest version of , Nam helper image. (even with CCO Account)
in addition i have a brand new NAM Module that contains NAM Helper Image but I couldnt find a way to tranfer this image via ftp to ftp server
View 1 Replies
View Related
Jul 31, 2012
I am getting drops in MRTG graph. Pgm nhiPoller[Net]: Received large delta from 'hyd-rt3845-01-GigabitEthernet0/1'. Poll is dropped (OID in error is ifInOctets. Delta is 3989641522. Old value is 4239690170. Current value is 3934364396.).
[Code]...
What could be the reason for the polling drops and is it IOS bug.
View 3 Replies
View Related
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Nov 7, 2011
I'm monitoring an WAE 7300 content-engine on our network. I constantly see that the graph hit over 90% on CPU utilization. But when I logged into the box and performed a "show processes CPU", it's showing a pretty low CPU usage. I'm using the HOST-RESOURCES-MIB file OID 1.3.6.1.2.1.25.3.3.1.2 to check CPU load. For other things such as memory usage, status of intefaces, etc... using that MIB file shows correct information. The one I got from SNMP or the one I saw when I logged into the box?
View 1 Replies
View Related
Sep 10, 2012
Cisco 2621XM running 12.2.Would like to configure MRTG on an outside box for monitoring & would love some assistance with getting SNMP up and working.
-My outside box is 38.117.168.x
-Router outside interface is 38.117.168.x1
When i try and run cfgmaker from my mrtg box im receiving an snmpwalk problem and no info could be retrieved..
View 1 Replies
View Related
Dec 19, 2011
The other day 3rd party supplier ran some stats on our Gigabit link between 2 Cisco catalyst 3750Gs.now the graphs produced showed only a Maximum output of about 100Mbps ( 5 minute intervals) yet when I do a show interface it shows a lot more always 150Mbps and more. So I did my own Perl script doing an "sh interface" every minute and then graphed it, and the results were a lot different to the MRTG results.Questions: I know MRTG uses SNMP to get the traffic is there a bug in the SNMP, what OID does it use?does the "sh interface" give the correct results?
View 2 Replies
View Related
Aug 25, 2012
I have taken on a new client who has the following setup, BT Infinity, Vigorpro 5510, and SBS 2011 server. I was involved with unpacking and seting up the equipment to get client up and running. I have never setup a firewall before, and after contacting Draytek, they guided to get BT infinity, 5510 to talk so that the server was able to get onto the internet. The setup was then left in its default state.All was fine until lately, the client keeps losing internet approx same time most days.My problem is how do i get the 5510 properly configured to talk to BT infinity, and sbs 2011. I always get lost when it come to playing with IP address. Also the client has a fixed IP address supplier by BT, so want to know how to setup the vigorpro with this address. [code]
View 1 Replies
View Related
Apr 10, 2011
a few weeks ago I started hosting a server for a game from my computer. It's been working fine and I've been having no problems except for one.After a few hours of hosting my server, my internet connection will immediately drop down to 1.0mbps, and I lose all connection to everything until I reboot my computer.I'm using a wireless internet adapter right now and having this problem, but when I used a wired connection a similar thing would happen where my entire connection would "lock up" in a way. I couldn't connect to anything until I rebooted my computer
View 4 Replies
View Related
Nov 5, 2012
It seems that whenever I go on newegg, I lose my internet. It will regain signal quickly, but is a huge annoyance. I cannot shop nor look at parts pricing without this disruption. It is only when I am on newegg does this happen.
View 1 Replies
View Related
Sep 29, 2012
I lose internet connection every day in the same time etc.i lose it in 2pm and i get it in 7.pm and tomarow again lose it in 2pm get it in 7pmit is not virus i have cleaned every infection whit Malwarebytes,Emsisoft,Hitmanpro,SuperAntispyware and Spybot
View 4 Replies
View Related
Nov 18, 2012
I CONSTANTLY lose connection to the net .Then it takes forever to rejoin the net.I know this PC has ASUS Wireless Console 3 installed on it. I have, in the past, tried a few fixes offered on websites for suggestions when you lose wireless connection (i.e. Setting a static IP to connect to, turning on firewalls, etc.) none have worked.
View 14 Replies
View Related
Nov 3, 2011
I have a very well updated Laptop running XP well patched with IE7.I have run all the malware scans and there is nothing wrong on the PC.After exactly 10 minutes of the PC being on, wireless internet connection is lost, BUT:Signal Strength states "Excellent" I can't access any website at all on the web. (Except for "Facebook" for some odd reason?) I can't access it after the 10 minute mark but if I'm already on it, I can navigate thru it's site without being disconnected, don't ask me why I have tried the following:
- Dynamic and Static IP setting
- Turned on and off windows firewall and rebooted each time
- Ran all kinds of malware detection and virus scans
- Disabled power management on network card
- I've tried different PCs on the same network and they're fine
- Tried ipconfig release and renew
- Tried repair connection
- Tried netsh reset
- Tried FireFox and other browers
- Logging off and back in doesn't work, must restart the computer to get another 10 minutes
View 6 Replies
View Related
Feb 4, 2013
I have a home plug network that goes like this:ndy's Room is my room, that homeplug goes into a switch that splits out to my PC and a wireless access point. Office goes into the main router that the internet feeds into. The living room connects to the TV, Sky box and PS3.Occasionally, the link rate LED on my plugs will drop to orange
View 1 Replies
View Related
Aug 7, 2012
If I do a factory reset on a router, does that mean the computers on the LAN will not be able to access the Internet?but then the router will configure it's self automatically to re-allow connection ?
View 2 Replies
View Related
Jul 27, 2011
I've recently added a desktop pc to the home's wireless network (using a D-Link DWA-125 Wireless N 150 USB adapter rev.A2) and it used to play nicely with the other devices. After switching out the router to an Actiontec V1000H my computer has begun losing most connectivity when the PS3 is turned on.
The pc still sees the network and there is a little activity there it seems. Everything runs fine when the PS3 is off and in the Wireless Network Connection Status display the speed is usually listed at 65-75 Mbps. But when the PS3 is turned on it reads 6.5 Mbps with the IPv4 connectivity bouncing between "internet" and "limited". Windows' automatic diagnosis is "Cannot communicate with DNS server".
I tried assigning static IP addresses to the pc and ps3 thinking there was a possible IP conflict with the dynamic addresses. Thinking there could be a conflict with ports I read up on port forwarding but my knowledge of networking is limited and I'm not even sure if that is the problem.
There are alot of other devices connected, 2 laptops, 2 iPod touches an iPhone the PS3 and now this old desktop clunker. I figure it's possible that the router is getting overloaded with everything and the PS3 just pushes my computer's bandwidth out the window but I would think that there would be some noticable drop in performance on the other laptops as well, which there hasn't.
View 19 Replies
View Related
Aug 8, 2011
Why does my acer laptop lose connectivity?
View 1 Replies
View Related
Jan 3, 2013
So i setup an Asus RTN66U router with an HP 1800 24 port switch. Ive got 2 PC's,xbox,cablebox, and wii(wireless).about every 5 minutes or so, it seems I lose connection. Its very apparant when I play BF3 cause it will close the game and say connection with server timed out.My question is how should I troubleshoot this. How do i pinpoint router, switch, or modem or something im missing.
View 9 Replies
View Related
Sep 23, 2012
I have a desktop and several laptops and other devices running on a wireless network. Whenever the desktop is asleep or shut down, all the other devices lose connectivity to the internet. If the desktop is on and running, everything else works perfectly.
View 9 Replies
View Related
Mar 7, 2012
About every 20 minutes, my internet connection, which otherwise runs well, just drops out randomly. When I diagnose the problem, it tells me "Cannot communicate with Primary DNS Server (50.30.208.77)." If I leave it alone, it corrects itself after a couple of minutes, but I can also reset the local area connection and that will get things working again as well. This started a few days ago, and I was hoping it would just go away, but it has not. To reiterate, my connection is fine for about 20 minutes at a time, but then it will just drop out for seemingly no reason. I don't use wi-fi, I'm connected via an ethernet cable to an outlet on my wall. I've tried different cables and the problem persists, so I don't believe it has to do with a faulty cable. I didn't change anything about my hardware or software the day this problem sprung up. [code]
View 3 Replies
View Related
Jun 5, 2012
For over a year there was no issue with the wireless router, then all of a sudden the connection was lost even though the signal was strong. When trying to figure out what was wrong, I accidentally reset the router. I had not used one before, so I am not too knowledgeable. The router had been my previous roommate's, who had set up the password, etc and I had been using it with that set-up, but now I had no password. I tried to reconfigure and set up a new password through the D-Link administrator, but could not get it to work. It is a D-Link DIR-655 and I am using an iMac. I finally just bought an Ethernet cable and plugged in directly,since I had no password protection. But even with the cable plugged in, I will lose the connection and have to restart the router to get it back - which has even happened while I am using the internet.
View 1 Replies
View Related
Jun 26, 2011
Connected to "clear" lose signal every few seconds-WHY! just lost my signal again!
View 2 Replies
View Related
Jan 20, 2012
We are a small business with about 9 Macbook pros and 3 PC's connected wirelessly to the router. The Mac-computers sometimes lose their wifi-connection to the router. When this happens they have to select the wifi network again from the menu, to reestablish their internet connection. For some of the clients, this happens about once each day and for others multiple times a day. The problem doesn't seem to appear on the PC's.
I have tried to solve the problem by making DHCP reservations for each computers MAC-address, but with no luck. I also tried to set the 802.11 Mode to 'Mixed 802.11n and 802.11g', and turning WISH off. I read that the connection can be disturbed, if other wifi-networks in the area uses the same channel, so I changed it to channel 3, based on a scan of the network, where 3 appeared to be the least used. The WPA Mode is set to 'WPA-2 Only' and Cipher type is 'TKIP and AES'
The Dir-655 is hardware version B1 and the firmware is 2.0.
View 13 Replies
View Related
Mar 19, 2012
We are having several workstations that are momentarily losing connection to our Windows Server 2008 machine that hosts their Documents etc.It seems like a momentary disconnection and not everyone has complained although I'm guessing that unless you are trying to locate a file etc at that moment you might not notice.Here is the error message I see in the event logs on the server:
-Source: srv
-EventID: 2012
-Level: Warning
While transmitting or receiving data, the server encountered a network error. Occassional errors are expected, but large amounts of these indicate a possible error in your network configuration. The error status code is contained within the returned data (formatted as Words) and may point you towards the problem.So, where would you guys start with something like this? Either my HP Procurve 1800-24G doesn't have much in the way of error logs, or I don't know where to look.Would you start with changing port on the switch, changing network cable or do you think it's more likely to be something on the server itself?
View 6 Replies
View Related
Dec 9, 2010
D-Link Dir-655 A3 lose internet connections between 5 to 60 min.
I use Telewell TW-EA501 v3 (b) ADSL modem and Windows 7 64bit Windows firewall + Microsoft security essentials
I have done:
- Enable / Disable NTP Server
- Wish is turned on / Off
- In Firewall it says
[Code].....
View 4 Replies
View Related
Sep 27, 2012
I got a new router, a Cisco Linksys EA3500, and everything works fine and no one else in my family notices anything. Everything works and I don't have trouble accessing the internet and I always get 5 bars, but whenever I play a game online it will disconnect me after a while. Sometimes it disconnects me after 5 minutes and sometimes after 30 minutes. The only games I play are Arma 2 and Garry's mod and I have the same problem with both games. The weird thing is that I talk to friends on steam when we are playing and it doesn't get disconnected I can hear them fine, and my internet access bar at the lower right doesn't say I'm disconnected. Streaming and downloading work as well. I have no idea what to do, we got a new router because the old one was faulty and we called our isp and they said there was nothing wrong on their end it.
View 1 Replies
View Related
Mar 20, 2012
Aironet 1142, two units, using WPA Radius to IAS on Windows 2003. I have a problem with Macs beginning to surface. One laptop, OSX 10.6, ran fine for a couple of weeks. A problem started occurring, while using the network, communication will stop. The Mac still shows connected on the laptop, and it shows associated in the interface on the Airnonet. However, there is no data transfer. I open a terminal and ping, there is no response. After sitting for awhile trying to ping, it will start again and communicate. After letting the laptop sit for awhile, the same things happens. The connection can be disconnected and reconnected on the laptop to restore connectivity. I did a round of things on the Mac to eliminate problems in configuration there. The same thing happens with both Aironets. Today, the when the problem occured, a user with an iPhone experienced the same thing. This was a first for that iPhone. Another Mac laptop, a newer model, did not experience the problem.
As I am writing this, a user with an iPad now just emailed that he is having trouble connecting. We just recently upgraded this customer to Aironets and disconnected a conglomerate of other products. The last one to be disconnected was a low cost Trendnet, that this iPad user was previously connecting to with no problem. The other device he would have been using in a different area was a Mac Airport WAP.
On the Aironets, I have CCX turned off, have set speed settings to default.
View 4 Replies
View Related
