I am getting drops in MRTG graph. Pgm nhiPoller[Net]: Received large delta from 'hyd-rt3845-01-GigabitEthernet0/1'. Poll is dropped (OID in error is ifInOctets. Delta is 3989641522. Old value is 4239690170. Current value is 3934364396.).
[Code]...
What could be the reason for the polling drops and is it IOS bug.
Running Asa5510, 8.2.5, with asdm 6.4.5 and I am looking for a graph in asdm that will show me what protocols and internal ip addresses uses the most traffic. Maybe a bit like "Top 10 protected servers under SYN attach". My reason for this is of cause I see a very high traffic pattern from one of my interface during the day and need to identify what is using bandwidth, protocol and source address.
I could use Net Flow feature in the Asa, but it´s not "real time" and forces me to setup a net flow collector. Can 8.2.5 not give me this information with built-in graph/tools?
Is it possible to get the result in th event list in the form of graph, ie. like delay,throughput in the form of graph
View 3 Replies View RelatedRegion : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
I want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
I'm monitoring an WAE 7300 content-engine on our network. I constantly see that the graph hit over 90% on CPU utilization. But when I logged into the box and performed a "show processes CPU", it's showing a pretty low CPU usage. I'm using the HOST-RESOURCES-MIB file OID 1.3.6.1.2.1.25.3.3.1.2 to check CPU load. For other things such as memory usage, status of intefaces, etc... using that MIB file shows correct information. The one I got from SNMP or the one I saw when I logged into the box?
View 1 Replies View RelatedCisco 2621XM running 12.2.Would like to configure MRTG on an outside box for monitoring & would love some assistance with getting SNMP up and working.
-My outside box is 38.117.168.x
-Router outside interface is 38.117.168.x1
When i try and run cfgmaker from my mrtg box im receiving an snmpwalk problem and no info could be retrieved..
After upgrade C7609S routers from:c7600rsp72043-adventerprisek9-mz.122-33.SRD4.bin to c7600rsp72043-adventerprisek9-mz.150-1.S3a.bin I lose interface with ip mpls configure form the MRTG SNMP pooling system. cfgmakre not see any more that interfaces (intrefaces fall on ($if_ok) filter). Other interface which not have a ip mpls configured is normally visible in the our MRTG monitoring system. From my site it is looks like that interface when I configure ip mpls go to unknown state for MRTG. That interfaces are not any more ethernet type.I can reach interface with configure ip mpls only with manual configure *.cfg file with ifindex value.
View 0 Replies View RelatedThe other day 3rd party supplier ran some stats on our Gigabit link between 2 Cisco catalyst 3750Gs.now the graphs produced showed only a Maximum output of about 100Mbps ( 5 minute intervals) yet when I do a show interface it shows a lot more always 150Mbps and more. So I did my own Perl script doing an "sh interface" every minute and then graphed it, and the results were a lot different to the MRTG results.Questions: I know MRTG uses SNMP to get the traffic is there a bug in the SNMP, what OID does it use?does the "sh interface" give the correct results?
View 2 Replies View RelatedIs there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies View RelatedRunning an ASA 5500, and using ASDM to connect. I need to view the historical metrics in graph form for traffic overview, that is shown on the firewall dashboard. I have enabled historical data, but all I see the 5 minute intervals.
View 4 Replies View RelatedIs there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies View RelatedMy internet is typically just fine but when I try to use LAN it cuts in and out every few minutes, which as you can imagine ruins everything. Currently using wi-fi as my Ethernet port somehow has ceased working. No other computer wired or wireless in my house has this problem.
View 2 Replies View RelatedI have 3 routers all running OSPF. each of the three routers have 2 networks they are advertising..NAT Overload breaks OSPF Adjacency
[code]...
I have an ASA 5505 running 8.2
I used the ASDM wizard (6.3) to set up a remote VPN. After slightly adjusting the wizards configuration the VPN is working well.
Now I need to change the Outside interfaces IP address. When I do that the VPN no longer works. If I change it back to the original value the VPN works again.
What configuration changes do I have to make regaurding the remote VPN after changing the outside interfaces IP address?
I have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedSo (foolishly) I let the software updater delete Java 6 (which only Apple provides), and I installed Java 7 from java.com. Was running ASDM 6.4.9, all I got was the Java 7 splash box. Updated ASDM to 6.4.9-103, same problem.
I can run ASDM in one of my VM's, but it's a pain.
I using cisco 837 for incoming remote access VPN connections with are working very well but I recently created one outgoing easy vpn connection and I have issue since that time. As soon as easy VPN is up and established successfully I lost remote VPN access to internal subnet.
Where is :
Internal subnet: 192.168.172.0/24
remote VPN pool 192.168.24.2-6
Take a look at config attached and point me at missconfiguration
I'm trying to portforward for a game, and in order to do so, I'm setting up a static IP. I've portforwarded in the past and all's been fine, but when I'm trying to set a static IP now it allows me to portforward and host the game, but whenever I try to log into any sort of website, it cannot find the page. The only fix to this is to allow it to obtain the IP address automatically. I've had a static IP in the past and yet I've never run into this issue before.
When I go to my TCP/IPV4 settings under the properties of my selected internet connection, I open up my ipconfig(I'll post it below) and select "Use the Following Ip Address". I then input 192.168.1.73, to change it to that.
Then, I click on the subnet mask box and it auto-fills 255.255.255.0, which is listed under ipconfig anyways, and for default gateway I input 192.168.1.1. I leave the DNS server boxes blank because it doesn't list them under ipconfig and it's what I did in the past to achieve the same results. After I click OK, the issue I listed above begins.
Code:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Tim-PC
Primary Dns Suffix . . . . . . . :
[Code].....
Windows 7 32 bit laptop ----> Windows 7 64 bit PC with USB network adapter.
I'm trying to move a folder from one computer to the other. There are about 300 files totalling 3mb.
At around "234 files remaining", the transfer freezes, and after a minute or so, the network connection on the destination computer is shown as Disabled. If I right click and choose "Enable", it makes the attempt, says "connection failed", and then "It is not possible to connect at this time. No network was detected. You may need to plug in your network cable to complete the connection."
What will fix it is unplugging the USB network adapter and replugging. But it only allows a little bit more transfer before it happens again.
I tried initiating the transfer from one computer, and again from the destination (bringing the files to it), but the problem occurs just the same. On additional attempts it will reconnect to the other computer and allow me to browse the files, but the connection crashes again without any more progress. My internet connection is fine otherwise, doesn't do this unless I'm transferring data across the network. I disabled Eset real-time protection but have windows firewall up (I'd rather not turn it off).
I have 3 computers at my home, a WRT54G V1 router.
2 of the computers are connected wired to the router, the internet on them works fine. My other computer I have connected via wireless, and when I try to go on the internet every 3 seconds it is saying not available. Now one thing I noticed was that when I connected to the wireless network it renamed it to my computers service tag. I confirmed this via a friends laptop. From "Busted" to "DCLZMRH1_Network", defenetly not something I did.
When this wireless computer is connected, ALL computers on the network begin having the same problem where each 3 seconds everybody is disconnected randomly. However as soon as I turn the wireless computer off, everything goes back to normal on the wired computers.
I have successfuly replicated this issue using 2 different wireless adapters, one USB, and one "wired" the one you put on the inside (lol) I have Brighthouse Networks cable internet
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista™ Home Premium , Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz, x64 Family 6 Model 15
[Code].....
I just spent a number of hours getting a site-to-site VPN tunnel and Cisco Quick Connect client running on my WRVS4400N and RVS400. Turns out the problem was the routers don't route IPv6 properly and it takes precedence over IPv4
View 1 Replies View RelatedI have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?
View 1 Replies View RelatedCurrently, I have a Cisco 4948 in office that connects to a remote site via BGP. From what I am seeing, when connecting a new device to this switchport (we connect devices to this switch for a multicast VLAN that is set up), the BGP link fails after roughly 20-30 seconds. The switchport is not tagged with a VLAN, or any other config. Just a plain old port. This outage continues until the port is added to the mutlicast VLAN.
View 1 Replies View RelatedACS5.2 time sync breaking once in near around one month and not able to authenticate after that .I am using domain controller (Windows Server 2008 R2) as NTP server for ACS .
What is the reason for it , is there any bug in 5.2 release or do i need to configure a thired device and point as NTP for ACS and domain controller.
I do have C3750G-12s switch which is not able to boot as of the expected. Every time when I break the stack and try to use console i got a weird output from my console output. we need the stack to be break and use those switch separtally .
[code]....
We have Four 2960S Switches in Stack. We have created Multiple VLANs. While Pinging from Member PC to Member VLAN IP on Switch, we are getting Higher TTL response & Some ping breaks for One Particular VLAN. While pinging from Member PC to Member PC, we are getting Normal Ping Response.
View 5 Replies View RelatedI have had intermittent problems with this PCI 802.11n adapter since I installed it. There isn't a new driver available, so that's not a solution. Issue is despite a strong signal, WiFi connection breaks sometimes when a session (either e-mail or browser) is started.The bar signal indicator goes from 5 bars to none, and mouse-over shows "no connection." About half the time the PC locks up (frozen cursor, no response to ctrl-alt-del, etc.).some of the time, the PC recovers after several minutes or more, other times locks up completely and the PC must be either forced reset or powered down manually. I've run CC Cleaner and check out the registry but can't find anything that works. PC is a 2.4GHz Celeron 1GB RAM running WinXP SP3 with all updates.Not related to browser; behavior is the same with Firefox, Chrome, IE. Also, other PCs on same network have no issues.On occasion I've triggered the lock-up while I had performance monitor running, and in the cases where the machine resumed running by itself, history showed no overloads typical of lock-ups. This PC is used almost exclusively for basic e-mail and browsing.
View 1 Replies View RelatedRegion : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : V7
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Avonline / Tooway
I can successfully make and receive VoIP calls via a Cisco SPA 303 IP phone, my iPhone 4S and a sogtphone on my MacBook PRO, using both DrayTEL and Sipgate as ITSPs. The Cisco phone is one of seven connected through the 3CX PBX software; but the iPhonne and the MacBook bypass the PBX and connect directly to the ITSP via the TP-Link router and the staellite modem.However, when I try to make or recive a second (simultaneous) call, both calls start breaking up.This happens both with the Cisco phones and with the iPhone and MacBook; so it's not a problem with the Cisco phone or with the 3CX soft PBX, since neither of these is involved when using the iPhone and the MacBook.I have tried various port forwarding configurations over the last few weeks, but still the problem persists. The current forwarding arrangement is ports 5060-5080 and 5090 and 9000-9049 for the PC running the 3CX software, and ports 5160-5180 for the MacBook. The iPhone has sipgate.co.uk set as both the Local and the External PBX IP, and the PBX port is 5060. The Local SIP port is 5964 and the Fisrt RTP port is 4000.
After some time of usage (typically days), I notice that Bonjour networking degrades. That is, the various Apple computers on my network can no longer see each other via Apple's Bonjour protocol. They can still connect directly using IP addresses however. The only solution seems to be a reset of the router. Are there some detailed logs I can look into to determine what the problem may be? The logs shown in the web interface don't seem detailed enough.
View 7 Replies View RelatedThe latest Mountain Lion (OSX 10.8) update somehow broke the Cisco VUSB software. I downloaded and installed Mountain Lion yesterday, and now the VUSB software is not working correctly. When I try to connect to my printer, an error appears saying the connection failed, but the dashboard shows it's connected. When I try to print, the printer is shown as unavailable. I have Cisco VUSB version 1.0.0 for OSX and the EA3500 Router.
View 9 Replies View Relatedhere comes the incident description: WRVS4400N breaks established VPN session if I am trying to connect to any LAN host via HTTPS.
View 1 Replies View RelatedI have a site to site tunnel (bidirectional) configured between two ASA 5510's (head office and remote office) running 8.2.2. I'm trying to upgrade one end (head office) of the tunnel to 8.3.2 but when I do that, traffic from the remote office to the head office isn't transported. Traffic from the head office to the remote office is still fine (remote desktop sessions, etc).
A quick comparison of the 8.2.2 config and the 8.3.2 config on the head office ASA look identical in terms of the crypto/site-to-site commands.Is there any Cisco guide created yet for creating site/site tunnels under 8.3.2? I'm able to upgrade both ASA at the same time if that's determined to be a prerequisite.