Adapter Breaks During Data Transfer Across Network
Feb 28, 2011
Windows 7 32 bit laptop ----> Windows 7 64 bit PC with USB network adapter.
I'm trying to move a folder from one computer to the other. There are about 300 files totalling 3mb.
At around "234 files remaining", the transfer freezes, and after a minute or so, the network connection on the destination computer is shown as Disabled. If I right click and choose "Enable", it makes the attempt, says "connection failed", and then "It is not possible to connect at this time. No network was detected. You may need to plug in your network cable to complete the connection."
What will fix it is unplugging the USB network adapter and replugging. But it only allows a little bit more transfer before it happens again.
I tried initiating the transfer from one computer, and again from the destination (bringing the files to it), but the problem occurs just the same. On additional attempts it will reconnect to the other computer and allow me to browse the files, but the connection crashes again without any more progress. My internet connection is fine otherwise, doesn't do this unless I'm transferring data across the network. I disabled Eset real-time protection but have windows firewall up (I'd rather not turn it off).
View 8 Replies
ADVERTISEMENT
Jun 19, 2011
I have recently been encountering file transfer probles across our network from wireless to wired, and vice versa. The transfer will start and process about 50% and then we lose internet connection, and it requires a router reboot to get connectivity again?
View 7 Replies
View Related
Mar 23, 2011
how can i connect my laptop in network so that i can transfer the data from another pc to my laptop.Also provide the information how to use ethereal software for internet traffic?
View 1 Replies
View Related
Mar 7, 2012
I would like to connect 3pc via switch and let them connect and be able to transfer data from one pc to another using network
View 1 Replies
View Related
Apr 6, 2012
Which network provides the highest data transfer rate?
View 1 Replies
View Related
May 2, 2013
we have ASA 5510 Configured. this is regarding site-to-site VPN.
View 1 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
Sep 20, 2011
i have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
View 3 Replies
View Related
Aug 24, 2012
I would like to conect a USB device to a computer using WiFi instead of the USB cable the device has. The thing is that I'm not sure about the drivers. Is there any USB Wireless device that transmits the USB data "raw" and the receiver plugged to the computer gets the data with the driver of the remote device in the own PC?
View 1 Replies
View Related
Sep 2, 2012
I have a new Palm Vx and have installed Version 3 Palm Software followed by an upgrade to 4.0.1.This works fine with the new Palm but I can't transfer all the data from my old Palm (almost 12 years of stuff) to my new Palm.
View 1 Replies
View Related
Aug 4, 2011
I am currently using Win XP in my desktop. I am planning to buy a Laptop with Win7 o/s. S how to transfer data from XP desktop to Win7 laptop uisng the LAN cable?
View 2 Replies
View Related
Feb 22, 2013
I have a laptop and a pc...i want to transfer loads of data (about 100 gb) from the laptop to the desktop.I have NO means to do it wirelessly.how to accomplish this so seemingly cumbersome task via wires? (i read in some other places about connecting it via lan wire and then changing the ip addresses.where on my desktop will i see the data of my laptop?
View 5 Replies
View Related
Apr 11, 2011
I have 2 cat 5 cables one has the network jack end on it and the other end has a usb end? What is this used for? Can it be used to transfer data from one computer to another?Also how can i tell if I have a crossover cable?
View 3 Replies
View Related
Jun 5, 2011
I was assembling and testing some custom production machines here, and I had to perform a data transfer between two windows 7 machines through an HP 1400 switch. I saw 100MBps transfers for the first time. I only wish I could get the main network to operate that fast.
View 13 Replies
View Related
Dec 2, 2012
just upgraded my ASA5510 from IOS 8.25 to 8.42Everything is running fine apart from one VPN between ASA5510 and cisco 887V router.The VPN session is up but no data traffic is being passed through The tunnel although this VPN was working fine with old IOS. The tunnel is up but no data is passing through IKEV1 session.
protected vrf: (none) local ident (addr/mask/prot/port): (10.0.12.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (172.16.0.0/255.255.0.0/0/0) current_peer xxxxxx port 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 0, #pkts encrypt: 0, #pkts [Code]...
View 1 Replies
View Related
Dec 15, 2011
I have a laptop running Windows XP that has a wireless card inside.
I have a Single Board Computer (SBC) running Linux that has an 'wireless access point' connected to one of it's Ethernet ports. I want to be able to transfer data between the laptop and the SBC wirelessly (cabling is not an option)
The 'wireless access point' I am using is the EnGenius EOC5611P - it can be configured for:
1. Access Point
2. Client Bridge
3. WDS Bridge
4. Client Router
I don't know which one of these I need,so working that out would be a good start!
View 1 Replies
View Related
Nov 23, 2011
RV110W connected to ISP via PPPoE. MTU is default setting - 1492. IPSs tarif - 100 Mbit/sec IN, 40 Mbit/sec-OUT.When the laptop is connected to RV110w via ethernet the data transfer rate is 45 Mbit IN / 25 Mbit OUT.When a laptop is connected to ISP directly without a router a data transfer rate is 95 IN / 35 OUT.
View 0 Replies
View Related
May 16, 2013
I've recently upgraded the configuration on one of our 1130 series standalone access points. I've implemented RADIUS authentication, WPA2 encryption etc. in an effort to make our network more secure. While this part seems to be working as planned, our data transfer speeds have taken a major hit. On our test AP, with only one laptop connected, the laptop will report a connection at 54 Mbits. When using any speed test service the speed reported is approximately 15 Mbits. We have 100 Mbit internet, and desktops connected to ethernet show much higher speeds. When transferring files via our own LAN, data transfer rates average approximately 2 Mbytes/second. I've tested this on 3 separate laptops, some relatively new, and it seems they all get the same speeds.
Long story short, our wireless seems to be operating under a third of its reported speed.
View 2 Replies
View Related
Jul 8, 2012
I am going back to college and I will need a router. Both my roommate and I were on the same router went over our bandwidth usage a number of times last year. I've done a bit of research and have come up with a few options: Asus rt-n56u, netgear wndr 4500, and the apple airport extreme. Both my desktop and laptop pc so I'm not sure if that effects the outcome. I am going to need a usb port for an ext hdd, which all of them have. All of the routers have a 5hz signal for better streaming. Would I be able to use the apple airport? It seems the have the best reviews. But I question the compatibility and some of the reviews due to possible fanboyism. Also, If I connect my desktop to the router via a crossover cable and have an ext hdd hooked into the router can I transfer files to the ext hdd and stream that data over a 5 hz signal?
View 2 Replies
View Related
Aug 2, 2012
I'm using Pix 501 with firmware: Version 6.3(3)I have problem with Pix 501:
+ transfer rate data between interface outside and inside very slow, even between 2 interface inside.
+ I have test file transfer between 2 PC connect via interface inside.
+ Results transfer 1 file 1MB with total time 60s
I don't upgrade software current from 6.3(3) to 6.3(5) via TFTP. It's error Please see attach file.
View 2 Replies
View Related
Feb 5, 2013
I am trying to connect a Control network that can not have access to the Internet, or any other network for that matter, to my Admin network so that I can retrieve trend data about the plant that goes into a database. Right now the process is print information, hand jam into excel spreadsheet, print again, and hand jam into another excel spreadsheet on the other network. Reports are printed automatically once a day, but would like a simplified way of getting data from one network to the other without having to re-enter data several times. Current policies stipulate no USB drives connected to Control systems. Even if we could loosen that, personnel needed to transfer data is not available and going to each individual machine would take more time than current system.Now that background is laid, I have two 2911 ISR routers with EIGRP configured, each with a 4 port EHWIC card. The 3 L3 ports on the router are setup as follows: interface G0/1 to the internet, interface G0/2 to a wireless back haul, and interface G0/0 for IT network. I then have 3 VLANs setup on the EHWICs for our Admin network. We will move the IT network to a VLAN on the remaining EHWIC port and connect the two 2911's through the G0/0 interface. I am going to have one computer on my Administration network dedicated to receiving the information and have a program that will take that data and import it to a database. I need to allow only that computer to receive traffic from the Control network and I need no traffic to flow back into the Control network. In other words I will transmit data from the control network to the admin computer using one protocol (TFTP more than likely) and block any other traffic coming out of and going into the Control network.
View 1 Replies
View Related
Dec 11, 2011
So I have a really neat computer sitting here, 2500K, P8z68-v, samsung 830 64gb ssd, corsair vengeance 16gb, deskstar hdd, firepro v5800
I have a non-descript trendnet 56K v.92 dial up modem installed to pci slot1 on my mobo.The phone company says they can't get a quicker connection than 31.2 Kbps established to dial up users in this area.The real issue is the data transfer rate.I have seen it reach as high as 6.xx Kbps but generally hovers around 2.5 Kbps.Now it is down to 1.xx Kbps and I took the last 48 hours downloading all the updates for windows and several other updates for hard ware etc.Now I need the ATI firepro update and 114 Mb will take over 16 hours at my average speed, and some 32 hours at the new slower speed
View 17 Replies
View Related
Jun 6, 2012
Customer production environment is nexus 5000 use 1 G interface * 4 and config Port-channel ( LACP ) uplink to C3560 , The port channel link is 802.1q trunk , but Data transfer is low , the sh int display as follow :
Why transfer performance pool and how to fix
N-5548UP# sh int ethernet 1/30Ethernet1/30 is up Hardware: 1000/10000 Ethernet, address: 547f.ee14.ed25 (bia 547f.ee14.ed25) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA Port mode is trunk full-duplex, 1000 Mb/s, media type is 10G Beacon is turned off Input flow-control is off, output flow-control is off Rate mode is dedicated Switchport monitor is off EtherType is 0x8100 Last link flapped 9week(s) 6day(s) Last clearing of "show interface" counters 20w2d 30 seconds input rate 152 bits/sec, 19 bytes/sec, 0 packets/sec 30 [Code]...
View 1 Replies
View Related
Apr 3, 2013
Region : Ukraine
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.11 Build 121102 Rel.51321n
ISP : Volia
Is it possible to extend the functionality of USB in future firmware for data transfer? More detail about the problem [URL]can at least in beta partially implemented increase data transfer USB?I bought this router, and as all users lose .... With the Internet, download files faster than with external screw via USB.
View 4 Replies
View Related
Jun 8, 2012
I need a software that i can use to transfer files from one windows PC to another over the LAN network.I've tried "Quick'n Easy FTP server Lite" and it works, but its really slow (About 2MB/s) ( i know my hardware can go much faster than the software is allowing). But at least the speeds were constant and unchangingI have also tried Windows Easy Transfer. But that software makes it a bit harder to send back and for whenever i feel like it, and although sometime i would hit speeds 5 times faster than with the previously mentioned software (about 12MB/s) , those speeds were not constant. It would be slow (around 1MB/s) and then spike up, and then go back down, and repeat in that fashion
View 8 Replies
View Related
Sep 14, 2011
I recently bought a new laptop for university, but before I go I want to transfer all my PC data to it (which includes large amounts of music and films). Effectively, or, well, uneffectively I guess, I set up a Home Network sharing system between the two computers. After a bit of fiddling around, I managed to connect the two so I could transfer date directly from the PC to the Laptops desktop.However, with the CAT-E Ethernet cable (which I thought was capable of 100mbps) its actually sitting just under 9 mbps transfer speed.
View 1 Replies
View Related
Feb 13, 2011
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
View 4 Replies
View Related
Feb 28, 2012
My company have a Cisco PIX 525 firewall which is cater for NOC internal data network and also voice network, the subnet for data network is 192.168.2.0/24 and the subnet for voice network is 172.16.2.0/24. someday this NOC firewall was faulty. I was migrated the data network from this NOC firewall to the other temporary firewall just at the moment. And the voice network i migrated it from where it orginal at NOC firewall to a VOIP system which actually having a connection with my temporary firewall(This temporary FW only to take the traffic of data network). After the migration of data network from old firewall to temporary firewall and also the migration of voice network from old firewall to PABX system. The subnet for data network remain the same as 192.168.2.0/24, but the subnet of voice network i edit from 172.16.2.0/24 to 192.168. 3.0/24.Now when i want to use one Cisco router 2600 to replace this temporary firewall then facing problem at the voice network....The data network after migrated from temporary firewall to new 2600 is ok, users can browsing. But when i trying to at the same time when the data network been migrated , it will affect the voice network which still located at PABX. ..user cannot make call...I was thinking reason because this voice network which currently in 192.168.3.0/24 is tight to somewhere on the 192.168.x.x at the old firewall internetwork. So, when i migrated the data network over to new router, it will also cause the failure of voice even thought after i migrated the voice system to new router.So when i do the disaster recovery back to the temporary firewall for both data and voice. The voice is resuming to normal.
View 4 Replies
View Related
Aug 19, 2012
The setup is Windows 7 64 bit transferring a 10 GB file to a Linux Ubuntu distro. Both have 1Gb NICs and the Switch is also a 1Gb switch.
View 2 Replies
View Related
Nov 4, 2011
Okay, I just replaced all my networking components in all my machines this week. I have three desktops 2 have Rosewill 802.11 b/g/n Wireless LAN PCIe card rated up to 300Mbps, one desktop with a Edimax USB wireless 802.11 b/g/n 150 Mbps, and a new Dlink DIR-615 route rated at 300 Mbps. So why is my transfer rate only 30 Mbps?
View 2 Replies
View Related
Feb 12, 2012
I love sharing on my home network to transfer files from one computer to the next. However, I will soon have tenants in my house sharing my network ...so they can use my Wi-Fi to get on the internet.I need a solution to give them access to the internet without losing my own network sharing ability.I do not want them accessing my files.I have Windows XP home and a Dlink WBR-2310 router.As I see it, I need to either upgrade to a router with a Guest Zone/Access feature ...OR..upgrade to Windows 7(?) to give myself more networking options (i.e. file sharing where I select the users or set a password). Currently the XP permissions are too general.
View 3 Replies
View Related
Apr 22, 2012
I have a wireless network with 2 desktop hooked up wired, and one laptop that's wireless. Accessing files on the desktop with xp installed is quick and transfers files at around 5-7mb/s. When I connect to my main pc with windows 7 on it, file transfer is EXTREMELY slow and almost always stutters and freezes. I've tried removing the drive from 'shared' and then adding it again, reinstalling my ethernet driver, swapping ethernet ports on the back of my router, and resetting it altogether. Still a slow transfer speed.I use workgroup all around, for xp and for 7.
View 3 Replies
View Related
May 11, 2012
We have a small home office with three computers, two new comps with win7 64 and an old comp running Vista32. Up until last week, the two 7's accessed files on the vista machine via a public folder, and everything was peachy, speed-wise. Trashed the vista this week and replaced it with a new desktop running win7 64. I backed up the old comp's files on the new comp, set up the new win7 home network, and everything went to hell. Both of the 'old' win7 machines can access files on the new, but the speeds are unbearable. It takes, literally, over 10 minutes for Accubid to load (accessing files on the new desktop), whereas it was pretty much immediate before. Quickbooks freezes for a minute and a half before it finally connects. A 60mb PDF file takes two minutes to copy. It even hiccups when I save a freakin' Word document. After some research I found that window's new home sharing network kinda sucks, so I turned it off on all machines and mapped network drives. Nothing.turn off remote differential compression, so I turned it off on all machines. Nothing. I disabled flow control on all machines. Nothing.The weirdest thing I did - I disabled auto-tuning and restarted all computers. I then opened Accubid and it opened immediately! I restarted the program 6 or 7 times, and each time it came up within seconds. I was ecstatic. Then my boss came in 5 minutes later and I opened Accubid to show him I finally fixed it. It took 10 minutes to load again, and I haven't been able to repeat whatever I had done since.
My ISP is ATT.
Modem - D-Link DSL 520B
Router - Netgear WNDR3800
Network is wired. Again, access to internet is blazing. Access to the computer 6 feet away from me is not.
View 3 Replies
View Related
