Cisco 2621XM running 12.2.Would like to configure MRTG on an outside box for monitoring & would love some assistance with getting SNMP up and working.
-My outside box is 38.117.168.x
-Router outside interface is 38.117.168.x1
When i try and run cfgmaker from my mrtg box im receiving an snmpwalk problem and no info could be retrieved..
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View RelatedI need to configure cisco router 2921 for snmp v3,
View 5 Replies View Relatedhow to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
send me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies View RelatedHow are certain settings/config transfered across to the AP's from the WLC, e.g. username and passwords, snmp strings etc.... I assume this is when the AP joins the WLC.More to the topic of the original question I had in mind, is it possible and if so, how? - to configure snmp read and write string from the WLC and push this config out to AP's. I can't believe someone will have to sit down (me) and SSH to 150+ AP's per WLC to configure SNMP.
One of the buildings lost connectivity to the WLC's breifly a couple of days ago and all seemed to have lost their SNMP settings. Connectivity was restored, but couldnt poll the APs. When I SSH'd on to a couple of AP's, and manually configured the snmp-server community xxxx ro - SNMP started working again. Since there are many, there must be an easier way of doing it.I've tried resetting the AP from the WLC and also powering down AP's and bringing them back up.
Using WLC 5508 on 7.4.100
Using AP's 2602 on IOS 15.2(2)JB$
Is there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
I have ASA running version 8.2.5 and using snmp v3 as below;
snmp-server group Authentication&Encryption v3 priv
snmp-server user SNMP_TEST Authentication&Encryption v3 encrypted auth md5 cisco123 priv aes 128 password123
snmp-server host IN 10.10.10.110 version 3 SNMP_TEST
LMS device credential is as per above SNMPv3 config.Can't get this to work. Digging aroung but no avail. I also try this on ASA 9.1 but same result.
My network is currently running with SNMP v2 configured in easch devices. With snmp v2 our LMS 3.2 server is working fine. However we have planned to migrate our network to snmp v3 . I have configured my few devices for SNMP v3 and added them to my LMS server.
Except DFM module these new SNMP v3 devices are working fine in all other modules. In DFM these devices are reflecting under "snmp timeout" group. I checked with device center -> management station to device; where the SNMP v3 connections are showing "okey"
following are tyhe configuration i have done in my devices.
snmp-server group v3g v3 priv read testr write testw
snmp-server user v3u v3g v3 auth md5 test123
snmp-server view testr iso in
[Code].....
Below is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedI want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies View RelatedI am getting drops in MRTG graph. Pgm nhiPoller[Net]: Received large delta from 'hyd-rt3845-01-GigabitEthernet0/1'. Poll is dropped (OID in error is ifInOctets. Delta is 3989641522. Old value is 4239690170. Current value is 3934364396.).
[Code]...
What could be the reason for the polling drops and is it IOS bug.
I want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
I'm monitoring an WAE 7300 content-engine on our network. I constantly see that the graph hit over 90% on CPU utilization. But when I logged into the box and performed a "show processes CPU", it's showing a pretty low CPU usage. I'm using the HOST-RESOURCES-MIB file OID 1.3.6.1.2.1.25.3.3.1.2 to check CPU load. For other things such as memory usage, status of intefaces, etc... using that MIB file shows correct information. The one I got from SNMP or the one I saw when I logged into the box?
View 1 Replies View RelatedI recently picked up a Catalyst 2960G and am trying to get SNMP management working over IPv6. I have the IP Address set to the local link, and can successfully ping and telnet to the switch (so the network can get traffic to and from the switch). However, SNMP packets just seem to disappear. I am running WireShark on my machine, and I see the packets go out to the proper IP, but nothing comes back. When I check "sho ipv6 traffic", I can see where there are UDP packets that are received, but, again, none going out. Also, when I run "sho snmp", all of the packet counts are 0.
Here are some relavant snipets from my "sho run":
interface Vlan1
no ip address
no ip route-cache
ipv6 enable
[code]....
I try to configure in both Clean Access Manager and Switch 3560E-24Ps on SNMP Version 2 protocol but I can't make it working together (For CAM and Switch 3560G-48Ps I can do that). [code]
View 3 Replies View RelatedWS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
After upgrade C7609S routers from:c7600rsp72043-adventerprisek9-mz.122-33.SRD4.bin to c7600rsp72043-adventerprisek9-mz.150-1.S3a.bin I lose interface with ip mpls configure form the MRTG SNMP pooling system. cfgmakre not see any more that interfaces (intrefaces fall on ($if_ok) filter). Other interface which not have a ip mpls configured is normally visible in the our MRTG monitoring system. From my site it is looks like that interface when I configure ip mpls go to unknown state for MRTG. That interfaces are not any more ethernet type.I can reach interface with configure ip mpls only with manual configure *.cfg file with ifindex value.
View 0 Replies View RelatedThe other day 3rd party supplier ran some stats on our Gigabit link between 2 Cisco catalyst 3750Gs.now the graphs produced showed only a Maximum output of about 100Mbps ( 5 minute intervals) yet when I do a show interface it shows a lot more always 150Mbps and more. So I did my own Perl script doing an "sh interface" every minute and then graphed it, and the results were a lot different to the MRTG results.Questions: I know MRTG uses SNMP to get the traffic is there a bug in the SNMP, what OID does it use?does the "sh interface" give the correct results?
View 2 Replies View RelatedI'm trying to change the RF Channel and Tx power level on my AIR-CAP36021-E-K9 from my WLC WISM2. I do the following;
Wireless --> 802.11 b/g/n --> Access Point --> Configure. I then select custom on both Power and Channel and make my change and then
click Save Configuration in the top righthand corner. I go back to 802.11 b/g/n select my AP and the power and channel setting have reverted back to their default selection.
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies View Relatedis it possible to get SNMP v3 on a Cisco ACS ?
View 1 Replies View RelatedI need to SNMP on Cisco Smart switch SF-200 24p. I cannot find any option on administration to turn snmp service on.
View 2 Replies View RelatedI'm not finding where set the snmp community on VPN 3000. I need read flow date on Ethernet interfaces. but I'm able only get traps from VPN 3000 to a system snmp but I don't get read from snmp community to VPN 3000.
where and how to I can configuration the snmp community on VPN 3000.
Is is possible to monitor bandwidth utilization of a PAT on an ASA? We're running version 8.2.
View 1 Replies View RelatedI have not used the ACS5.1 yet so watch out for the easy questions
1) Is it possible to generate report for the users who are inactive for say last 30 days? Customer is looking to audit these users to see if they really need access to any device.
2) Are there any known issues while assigning the priviligaes level to users. In current implementation of this customer users are always logged into priv 1 though they are assigning the priv level of 5. I understand with ACS 4.x we can enable the exec process and assign the priv under user/group policy. What are the configurations that customer might be possiby missing in this case?
3) Is there any SNMP or other notification available in ACS 5.1 where admin can be notified at the time a particulat set of user logs in.
I am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
I have a simple query for the issues I m facing currently.I have @ remote site remote site PIX firewall which is configurd to get the Snmp poll on the server locate outside via site to site VPN.There is another snmp server located also in inside which I’m not managing it .
========================================================================
below are the command for the snmp configured on PIX.
snmp-server host inside x.x.x.x community XXXXX ---This is not managed by us
snmp-server host inside x.x.x.x community XXXXX
snmp-server host outside y.y.y.y (private IP tunneled though VPN) poll community YYYYY ---Managed by us
snmp-server host outside y.y.y.y poll community YYYYY
[code]....
there are 2 snmp community & server defined in snmp-server host command for 2 different IP address belongs to snmp server and we can only define one global snmp-server community for any one of them .Question is how the snmp community take a precedence currently I am able to ping from my snmp server from outside to the PIX firewall outside interface over L2L VPN but somehow the snmp server is not listening when i do port query on 161 por!.
Seems like something simple, but can't find on Cisco.com. What are the max SNMP hosts allowed on an ASA 8.2 code? That would be Polls and Traps?
View 1 Replies View Relatedrequesting information via SNMP from my two stacked C3750X, running IOS 12.2(55)RE5. The stack is up and running and everything is just fine. There are three PowerSupplies installed with a PowerStack, also running like expectet.My problem ist to get the status-information about the chassis-fans. I couldn't find any information about the OID and the search results only in some non-useful information about the MIBs from Cisco which delivers only three information about installed fans (and fan-containers), so I guess these are the information about the fans included within the powersupply?! The chassis-fans are installed and the LEDs are green for all four fan-mounts, up and running.
View 4 Replies View RelatedI am looking for the SNMP OID to monitor the sh ip nat translations on a cisco 881.
#sh ver
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 26-Feb-09 06:01 by prod_rel_team
[code]....
I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
View 2 Replies View Related