Configure SNP Server For SNMp Trap?
Jul 1, 2011send me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies
ADVERTISEMENT
Cisco Firewall :: Configure ASA 5520 To Send SNMP Trap?
Apr 16, 2012Below is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
Cisco Firewall :: ASA 5510 / SNMP Server To Receive Trap?
Apr 9, 2011How to prepare my network for snmp,currently i don't have SNMP configured with community,so what is the requirement for that?what server i need to configure in order to receive SNMP traps coz last time i had issue ,one of my tunnels (terminated on asa 5510) goes down for 2 hours and i didn't realized that
View 7 Replies View RelatedCisco :: LMS 4.1 Taking SNMP Trap To Email Alarms
Feb 1, 2012Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
Cisco :: When Below SNMP Trap Type Triggers From Network Devices
Dec 7, 2012We are implementing fault management tool and for that we need information such as what type of traps are being triggered by router on what events..currently we have BGP, interface,reachability,h/w,syslog,authfail,config, trap types configured..All these are hitting in our fm tool but I need to know when these traps are being triggered by router.more importantly authfail, config, syslog, bgp.
View 4 Replies View RelatedLinksys Wired Router :: RV082 - Can The SNMP Trap To Field
Jan 25, 2011I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?
View 1 Replies View RelatedCisco :: 3750 Sw Is Not Sending SSH Login Failure SNMP Trap
Nov 22, 2011I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login
aaa authentication login default local
login delay 1
[Code].....
Cisco Application :: ACE 4710 Switchover SNMP Trap Notification?
Jun 20, 2012I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
Cisco Switching/Routing :: SNMP Trap For Syslog In Nexus 5K
Mar 30, 2013how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
Cisco Wireless :: 1130 AG - SNMP Trap On AP Max Associations Reached
Feb 21, 2012I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies View RelatedCisco Wireless :: WLC 7.0.98.0 / How To Convert Snmp Trap To Be Syslog Message
Aug 22, 2011Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
Cisco :: 2960 / 3750S / 3750X / 6504S - SNMP Trap Configuration
Sep 10, 2012I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
Cisco Switching/Routing :: 3750 SNMP Trap Send Every 30 Seconds
Dec 17, 2012I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?
View 1 Replies View RelatedCisco Application Networking :: ACE 4710 SNMP False Linkup / Down Trap Notification?
Feb 6, 2013We have two ACE4710 in a failover configuration with Software version A4(2.0). SNMP is setup and the receiver is able to receive SNMP traps.The issue is we are receiving a linkDown trap notification at least once every other day, followed shortly by a linkUp notification a minute later. We have checked all layer 2 devices connected to the ACE and cannot see any evidence that any link actually disconnected. We experienced no traffic lost, but this could be because a couple of the ACE links are bundled. The trap notification does not actually indicate which interface changed status. All links are Gigabits, and there are no packet drops either on the ACE or the layer 2 switch.
View 3 Replies View RelatedCisco :: Configure SNMP On Aironet 1130?
Jul 21, 2011I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View RelatedCisco :: Configure Router 2921 For Snmp V3?
May 19, 2013I need to configure cisco router 2921 for snmp v3,
View 5 Replies View RelatedCisco Switches :: How To Configure SNMP On SG300 Using CLI
Feb 3, 2013how to configure SNMP on the Cisco SG300 switches? I have the SG300-10P. I am not fully familiar with the new command line interface on this device, it was easy on the IOS but finding it a nightmare on this one.
I put the following command in but it didnt work.
snmp-server view Interfaces interfaces included
snmp-server community ACB123 ro 10.x.x.x view default
I tried to follow the guidelines on the cisco website but thats all Web interface based, i can only access the switch remotely via CLI.
Cisco Wireless :: AIR-CAP2602I-E-K9 Configure SNMP From WLC 5508?
Jun 11, 2013How are certain settings/config transfered across to the AP's from the WLC, e.g. username and passwords, snmp strings etc.... I assume this is when the AP joins the WLC.More to the topic of the original question I had in mind, is it possible and if so, how? - to configure snmp read and write string from the WLC and push this config out to AP's. I can't believe someone will have to sit down (me) and SSH to 150+ AP's per WLC to configure SNMP.
One of the buildings lost connectivity to the WLC's breifly a couple of days ago and all seemed to have lost their SNMP settings. Connectivity was restored, but couldnt poll the APs. When I SSH'd on to a couple of AP's, and manually configured the snmp-server community xxxx ro - SNMP started working again. Since there are many, there must be an easier way of doing it.I've tried resetting the AP from the WLC and also powering down AP's and bringing them back up.
Using WLC 5508 on 7.4.100
Using AP's 2602 on IOS 15.2(2)JB$
Cisco :: Configure SNMP Traps For Port 80 On ASA 5510?
Jan 30, 2012Is there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
Cisco :: 22621XM - How To Configure MRTG And Get SNMP Up And Working
Sep 10, 2012Cisco 2621XM running 12.2.Would like to configure MRTG on an outside box for monitoring & would love some assistance with getting SNMP up and working.
-My outside box is 38.117.168.x
-Router outside interface is 38.117.168.x1
When i try and run cfgmaker from my mrtg box im receiving an snmpwalk problem and no info could be retrieved..
Cisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst
Apr 12, 2012Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedCisco Switching/Routing :: Configure Snmp Traps For RPS 2300 Failure On 3750S?
Dec 7, 2011I want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies View RelatedAAA/Identity/Nac :: Configure Clean Access Manager And Switch 3560E-24Ps On SNMP
Jun 11, 2011I try to configure in both Clean Access Manager and Switch 3560E-24Ps on SNMP Version 2 protocol but I can't make it working together (For CAM and Switch 3560G-48Ps I can do that). [code]
View 3 Replies View RelatedCisco Firewall :: SNMP Server On PIX IOS 7.2 Over VPN
Sep 4, 2011I have a simple query for the issues I m facing currently.I have @ remote site remote site PIX firewall which is configurd to get the Snmp poll on the server locate outside via site to site VPN.There is another snmp server located also in inside which I’m not managing it .
========================================================================
below are the command for the snmp configured on PIX.
snmp-server host inside x.x.x.x community XXXXX ---This is not managed by us
snmp-server host inside x.x.x.x community XXXXX
snmp-server host outside y.y.y.y (private IP tunneled though VPN) poll community YYYYY ---Managed by us
snmp-server host outside y.y.y.y poll community YYYYY
[code]....
there are 2 snmp community & server defined in snmp-server host command for 2 different IP address belongs to snmp server and we can only define one global snmp-server community for any one of them .Question is how the snmp community take a precedence currently I am able to ping from my snmp server from outside to the PIX firewall outside interface over L2L VPN but somehow the snmp server is not listening when i do port query on 161 por!.
Cisco AAA/Identity/Nac :: Add SNMP Server IP And Community In ACS 3.2 Appliance
May 23, 2012how to add an snmp server ip and community in the ACS 3.2 appliance .
View 3 Replies View RelatedCisco Firewall :: Cannot Specify RO On Snmp-server Command With Older Pix 501 6.3
Oct 23, 2012i am wanting to open up snmp on a pix 501 6.3 version. I am planning on doing it with the following configuration: [code]
I noticed you cannot specify RO on the snmp-server command with the older pix. I don't want this configuration to open up any write access to the pix. Is there a way to specify only read only for snmp
Cisco Application :: SNMP Server Not Receiving Traps From ACE 4710
May 24, 2012Had setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
SNMP configuration on ACE
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514
[code].....
Cisco Switching/Routing :: C6500 / SNMP-server Traps For ISDN?
May 17, 2012Trying to migrate the config run on IOS 12.1 to 12.2 ?It seems there's no snmop traps isdn command support on 12.2.
where i can enable trap on ISDN over IOS 12.2 (33) sxj1 running on C6500 chassis?
Cisco Switching/Routing :: Catalyst 2950 - Release For Snmp-server Enable Traps Errdisable Command?
May 16, 2013We have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
Configure Windows Server As Both ISA Server And AD DC?
Jan 25, 2013I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
Cisco :: Send Trap From ASA?
Nov 25, 2011Is it possible to have the ASA send an SNMP trap when a particular bit-rate over an interface is exceeded?
View 2 Replies View RelatedCisco :: WLC 5508 Recent Trap Logs?
Dec 3, 2012I have a 5508 wireless lan controller we have two SSID configured Profile Name : Corporate and Guest When I go look at the Most Recent Traps all I see is Client with Mac address blah has joined your corporate, this goes on for sometime. But I am unable to see any of the Guest logs joining the network, I have since then grabbed my laptop and connected to the guest log. I still dont see any logs in Most Recent Traps for the Guest SSID WLAN configuration, I then blocked my Mac address and tried to connect again, No logs. I need to also montior the guest network is there some special tick box I need to apply for this to work? Once the guest is connected I can view them in the clients list but it never shows them on MOST RECENT TRAPS but I want to see the guests account connecting or failing to connect as we currently have a rogue device annoying me.
View 3 Replies View RelatedCisco Switching/Routing :: Trap To Monitor FEX On 5K?
Jan 7, 2013Which trap we need to enable to monitor FEX module on 5K.If FEX goes down due to link failure/power down we do not receive any trap on SNMP server. Ethernet1/5 is where Fex module in connected on 5K
Some sample log
2013 Jan 4 12:11:32switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
[code]....