Cisco :: WLC 5508 Recent Trap Logs?
Dec 3, 2012
I have a 5508 wireless lan controller we have two SSID configured Profile Name : Corporate and Guest When I go look at the Most Recent Traps all I see is Client with Mac address blah has joined your corporate, this goes on for sometime. But I am unable to see any of the Guest logs joining the network, I have since then grabbed my laptop and connected to the guest log. I still dont see any logs in Most Recent Traps for the Guest SSID WLAN configuration, I then blocked my Mac address and tried to connect again, No logs. I need to also montior the guest network is there some special tick box I need to apply for this to work? Once the guest is connected I can view them in the clients list but it never shows them on MOST RECENT TRAPS but I want to see the guests account connecting or failing to connect as we currently have a rogue device annoying me.
View 3 Replies
ADVERTISEMENT
Mar 26, 2013
I have recently noticed that in my WLC traps I keep finding lots of Mac addresses that have many hits on joining but it's the same MAC ADDRESS. Example Mac addresss'08:11:96:e4:1a:60,4Wed Mar 27 16:05:56 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate5Wed Mar 27 16:05:45 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate7Wed Mar 27 16:04:53 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate12Wed Mar 27 16:02:51 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate This has like 20 hits in the traps section and when I check my ISE this is also reflected on the authentication aspect. This is starting to occur with many different client laptops, why does it keep re-authenticatiing into the profile joined?Is there a Time to Live TTL setting I can set so it doesn't poll so often? The users aren't doing anything this is all occuring automcatically, I think it's the WLC 5508 controller not the ISE.
View 2 Replies
View Related
Dec 6, 2012
I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.
View 10 Replies
View Related
Apr 21, 2011
Where I can get the most recent install file for the ASDM-IDM Launcher software? I'm currenly running 1.5(41). Somebody mentioned they are at least up to 1.5(50), but he couldn't remember where the install file was. I checked Cisco's software download site, but nothing came up for the Launcher.
View 2 Replies
View Related
Jun 21, 2011
Wireless reception became poor after recent Windows 7 updates.Can't find recent windows 7 64 bit driver for this card.
View 1 Replies
View Related
Jul 23, 2011
So I have a netgear wireless router that my computer uses to access internet, then i have ethernet cable running from that netgear into my room to a linksys befsr41 router that I disabled DHCP to use as a switch. I have the ethernet cable going into the 4th slot and my xbox going into the 1st. I got it working however...and before i say this let me tell you, before introducing the linksys as the switch everything was working fine, both wireless to my computer and wired into my xbox straight from the Netgear. Ok back to my issue, while watching netflix on my xbox every 10 minutes or so i will get disconnected from the network on both my computer [wireless to netgear] and xbox wired to netgear through linksys. I was wondering if this could maybe be some kind of IP Address issue.
View 13 Replies
View Related
Jun 10, 2013
MY belkin router model no :F5D7234-4v1, recognizes only my laptop and my other devices such as mobile and tab are getting the signal and w-fi gets connected but the internet is not working. when contacted service provider he asked to upgrade the firmware. Is there any recent version firmware upgrade of the model. current version is F5D7234-4_UK_1.00.01.
View 1 Replies
View Related
Jun 9, 2013
what is the recent version Firmware update for Belking router model number : F5D7234-4v2
View 1 Replies
View Related
Sep 17, 2011
I lost the rack brackets for my switch in a recent move. Where can I get more?
View 1 Replies
View Related
Jan 23, 2013
I have one of the network every where routers by Linksys, model NR041. I realize this is an older model but it has been good for me ever since I ought it and I am wanting to find a recent firmware upgrade for this. Is anyone aware of a newer firmware upgrade & if so, where can I find it?
View 1 Replies
View Related
Nov 25, 2011
Is it possible to have the ASA send an SNMP trap when a particular bit-rate over an interface is exceeded?
View 2 Replies
View Related
Jan 7, 2013
Which trap we need to enable to monitor FEX module on 5K.If FEX goes down due to link failure/power down we do not receive any trap on SNMP server. Ethernet1/5 is where Fex module in connected on 5K
Some sample log
2013 Jan 4 12:11:32switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
[code]....
View 1 Replies
View Related
Jul 1, 2011
send me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies
View Related
Feb 1, 2012
Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
View 1 Replies
View Related
Oct 10, 2012
As part of troubleshooting a seperate issue, somebody on my 891 router had set logging trap debugging which shows as a line in sh run just above the access-lists. There is no syslog server however so I'd like to remove this entry, however when I do no logging trap debugging I end up with a no logging trap entry replacing the previous logging trap debugging entry. Is there away to be rid of this entry? I tried no no logging trap but of course that's an invalid command.
View 6 Replies
View Related
Dec 7, 2012
We are implementing fault management tool and for that we need information such as what type of traps are being triggered by router on what events..currently we have BGP, interface,reachability,h/w,syslog,authfail,config, trap types configured..All these are hitting in our fm tool but I need to know when these traps are being triggered by router.more importantly authfail, config, syslog, bgp.
View 4 Replies
View Related
Nov 22, 2011
I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login
aaa authentication login default local
login delay 1
[Code].....
View 7 Replies
View Related
Apr 16, 2012
Below is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
View 4 Replies
View Related
Jun 20, 2012
I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
View 1 Replies
View Related
Apr 9, 2011
How to prepare my network for snmp,currently i don't have SNMP configured with community,so what is the requirement for that?what server i need to configure in order to receive SNMP traps coz last time i had issue ,one of my tunnels (terminated on asa 5510) goes down for 2 hours and i didn't realized that
View 7 Replies
View Related
Mar 30, 2013
how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
View 2 Replies
View Related
Feb 21, 2012
I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies
View Related
Aug 22, 2011
Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
View 2 Replies
View Related
Sep 10, 2012
I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
View 3 Replies
View Related
Dec 17, 2012
I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?
View 1 Replies
View Related
Dec 9, 2012
I have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies
View Related
Jan 25, 2011
I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?
View 1 Replies
View Related
Feb 6, 2013
We have two ACE4710 in a failover configuration with Software version A4(2.0). SNMP is setup and the receiver is able to receive SNMP traps.The issue is we are receiving a linkDown trap notification at least once every other day, followed shortly by a linkUp notification a minute later. We have checked all layer 2 devices connected to the ACE and cannot see any evidence that any link actually disconnected. We experienced no traffic lost, but this could be because a couple of the ACE links are bundled. The trap notification does not actually indicate which interface changed status. All links are Gigabits, and there are no packet drops either on the ACE or the layer 2 switch.
View 3 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Dec 22, 2012
how to turn off this logs??
*Mar 2 13:26:07.919: %SEC-6-IPACCESSLOGP: list 101 denied udp 79.2.199.68(57143) -> x.x.x.x (34803), 1 packet
Router#
*Mar 2 13:26:09.766: %SEC-6-IPACCESSLOGP: list 101 denied tcp 108.15.116.235(63864) -> x.x.x.x (34803), 1 packet
Router#
*Mar 2 13:26:11.276: %SEC-6-IPACCESSLOGP: list 101 denied udp 24.130.2.212(26935) -> x.x.x.x (34803), 1 packet
View 3 Replies
View Related
May 24, 2012
I cannot read ACS 5.3 logs from my WCS. I have the ACS server added to the WCS. Below is the message I'm getting:
Unable to connect to any ACS View Server.Failed to access the WSDL at: { URL}. It failed with: {URL}. Do I need to install any special module on the ACS to support this?
View 1 Replies
View Related
Jun 16, 2011
I have a question about VPN Concentrator FTP Backup configuration to get logs on FTP server. I have configure FTP Backup with all details but I still do not see any logs on FTP server. Do you know what could be the issue? I have never used Concentrator and not sure what needs to be done to get in working condition. I am using VPN Concentrator 3015 series.
View 5 Replies
View Related
Nov 4, 2012
I am running two ASA 5520 routers synched up with eachother. I had a massive connectivity issue this weekend that I am investigating. Now I have figured out how to get the live logging but I need to know how to get the old logs from my router.
View 4 Replies
View Related
