Cisco :: 2960 / 3750S / 3750X / 6504S - SNMP Trap Configuration
Sep 10, 2012
I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
View 3 Replies
ADVERTISEMENT
Jul 1, 2011
send me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies
View Related
Feb 1, 2012
Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
View 1 Replies
View Related
Dec 7, 2012
We are implementing fault management tool and for that we need information such as what type of traps are being triggered by router on what events..currently we have BGP, interface,reachability,h/w,syslog,authfail,config, trap types configured..All these are hitting in our fm tool but I need to know when these traps are being triggered by router.more importantly authfail, config, syslog, bgp.
View 4 Replies
View Related
Nov 22, 2011
I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login
aaa authentication login default local
login delay 1
[Code].....
View 7 Replies
View Related
Apr 16, 2012
Below is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
View 4 Replies
View Related
Jun 20, 2012
I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
View 1 Replies
View Related
Apr 9, 2011
How to prepare my network for snmp,currently i don't have SNMP configured with community,so what is the requirement for that?what server i need to configure in order to receive SNMP traps coz last time i had issue ,one of my tunnels (terminated on asa 5510) goes down for 2 hours and i didn't realized that
View 7 Replies
View Related
Mar 30, 2013
how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
View 2 Replies
View Related
Feb 21, 2012
I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies
View Related
Aug 22, 2011
Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
View 2 Replies
View Related
Dec 7, 2011
I want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies
View Related
Jan 25, 2011
I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?
View 1 Replies
View Related
Dec 17, 2012
I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?
View 1 Replies
View Related
Feb 6, 2013
We have two ACE4710 in a failover configuration with Software version A4(2.0). SNMP is setup and the receiver is able to receive SNMP traps.The issue is we are receiving a linkDown trap notification at least once every other day, followed shortly by a linkUp notification a minute later. We have checked all layer 2 devices connected to the ACE and cannot see any evidence that any link actually disconnected. We experienced no traffic lost, but this could be because a couple of the ACE links are bundled. The trap notification does not actually indicate which interface changed status. All links are Gigabits, and there are no packet drops either on the ACE or the layer 2 switch.
View 3 Replies
View Related
Nov 13, 2012
I am trying to establish EIGRP neighborships with my inside switches (3750s) over the "Internal" interface, shown in green. The outside interface is g0/0 and don't worry, I've ensured EIGRP is not running there.The problem I'm having is that I need to monitor the "Internal" link so that if it goes down, the ASA triggers the failover to the secondary firewall connected to the other switch. I was told that the "secondary" keyword was what enabled this:
interface GigabitEthernet0/1
nameif Inside
security-level 100
ip address 10.10.2.2 255.255.255.0 standby 10.10.2.3
This is fine since I am able to compare this config to the firewalls that are currently in production elsewhere in the environment and this is what's in use there. However, in order to run EIGRP all the way to the firewall and not rely on something else like HSRP for the inbound traffic, I'd like to run the corresponding links (Gi1/0/22) on the inside switches as routed ports (no switchport) so that I don't have to establish neighborships with SVIs or something like that. I want the routing to be done directly to the port, leaving the interfaces for failover and our DMZ set up as switchports, since those can be layer 2.It's saying the Internal interface has failed now, probably because it cannot send hellos through this, since it's a routed port on the switch side. I'm wondering if this simply is an impossible design, unless there's a way to track this interface and trigger a failover if it goes down using another method.a method that allows me to track that internal interface (Gi0/1) and trigger a failover if it goes down.
View 1 Replies
View Related
May 5, 2012
I have a network with static routes witch I need to convert to OSPF.Never used OSPF, and do not have much experience in routing in general.The netvork is connected via some fiber links, but moastly wireless bridges.I have attached a drawing of how the network is.Routers are 3550, 3560 and 3750s.Each router is on a different physical site.
View 2 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Dec 10, 2012
I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
SNMPv2-SMI::mib-2.17.2.15.1.3.1 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.3 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.40 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.67 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.104 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.257 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.258 = INTEGER: 5
SNMPv2-SMI::mib-2.17.2.15.1.3.259 = INTEGER: 5
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
snmp-server community bic-zua-ro RO
View 3 Replies
View Related
Mar 2, 2012
I have NM-AIR-WLC6-K9 in Cisco 2821. Is there opprotunity to retreive configuration via SNMP as from Cisco Catalyst 2960?
View 1 Replies
View Related
Jan 19, 2011
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies
View Related
Jul 10, 2012
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
View 4 Replies
View Related
Sep 18, 2012
WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
View 3 Replies
View Related
Dec 18, 2011
i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies
View Related
Jul 19, 2012
I have configured below SNMP v3 commands in Cisco Router 7206VXR (NPE-G1) . I have tested with all option but it is not working . SNMP server is a SNMPc tool and I have configured user name and piv and authentication credential correctly in both side . Same configurations is working for all Cisco switches but not working for Cisco Router.
SNMP V3 configurations:
access-list 20 permit 43.194.10.0 0.0.0.255
snmp-server view readview iso included
snmp-server group readonly-group v3 priv read readview access 20
[ code]....
Router :
Host Name# sh versionCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.2(33)SRD7, RELEASE SOFTWARE (fc1)[ code]...
View 3 Replies
View Related
Jul 22, 2011
if there is document available for SNMP configuration for WLC 4404?
View 4 Replies
View Related
Aug 7, 2012
I am looking after a mixed collection of Cisco and HP switches and use a Perl script to extract configuration data.I use the ifStackStatus table (OID: 1.3.6.1.2.1.31.1.2.1.3) from RFC1573 to sucesfully obtain the EtherChannel data from the Cisco switches but, though I do obtain data from the same table from the Procurve switches it seems to bear no resemblance to Link Agregation. I could look at other tables and may have to - but would like to use this one in order to simplify the code.
View 2 Replies
View Related
Mar 23, 2012
I want to know how to retrieve the complete configuration for a Nexus via the snmpwalk or snmpget commands...
View 6 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Apr 7, 2013
I am trying to configure a new metro ethernet and have some questions about the configuration. The physical layout is a main office and two remote locations. The remote sites are point-to-point connections to the main office, tagged by the ISP with VLAN 130 and VLAN 140. The connections aggregate into one handoff at the main office, and are plugged into Catalyst 3750-X switches at all three sites.
View 8 Replies
View Related
Jul 19, 2012
We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies
View Related
Jul 2, 2013
I have RFID Reader (10.10.63.2 - 255.255.255.240) connected Cat-6 POE to ws-c3750x-24p-s - standard TCP/IP web service app pulling data from the reader every 250msec: I have my app server connect via vlan by ws-c3750x-24p-s IP address (128.1.70.1 - 255.255.0.0) as you can see its on a different sub net;
I can ping the device from the server - although I'm not getting any data coming through: my config are as:
0 [switch 1 provision ws-c3750x-24p-s]
1 [system mtu routing 1500]
2 [ip routing]
3 [no ip domain-lookup]
[code]...
I can ping the device from the server - although I'm not getting any data coming through.
View 19 Replies
View Related
