Cisco :: 7206 VXR - Configuration Of SNMP V3 Commands
Jul 19, 2012
I have configured below SNMP v3 commands in Cisco Router 7206VXR (NPE-G1) . I have tested with all option but it is not working . SNMP server is a SNMPc tool and I have configured user name and piv and authentication credential correctly in both side . Same configurations is working for all Cisco switches but not working for Cisco Router.
SNMP V3 configurations:
access-list 20 permit 43.194.10.0 0.0.0.255
snmp-server view readview iso included
snmp-server group readonly-group v3 priv read readview access 20
[ code]....
Router :
Host Name# sh versionCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.2(33)SRD7, RELEASE SOFTWARE (fc1)[ code]...
View 3 Replies
ADVERTISEMENT
Jun 22, 2011
There are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ####################################################################################################################################################################################################################################################################################################################################################################
[Code]...
View 2 Replies
View Related
Jan 10, 2011
ROUTER#sh run | i ip cefip cef table event-logip cefip cef accounting non-recursive load-balance-hash ip cef accounting non-recursive external
>snip<
ROUTER#conf tEnter configuration commands, one per line. End with CNTL/Z.ROUTER(config)#no ip cef accounting non-recursive load-balance-hashCommand authorization failed.
% Incomplete command.
ROUTER(config)#no ip cef accounting non-recursive load-balance-hash ?% Unrecognized commandROUTER(config)#^Z
cisco 7206VXR (NPE-G1) processor (C7200-JS-M), Version 12.3(10c)
How do I remove "ip cef accounting non-recursive load-balance-hash" from the config. I'd like to leave the box as I found it. Is it to do with an authority level or something more?
View 3 Replies
View Related
May 28, 2013
I have a 7206 VXR router between a several Mikrotik routers on our backbone. We have the Mikrotiks on both sides of the CIsco 7206VXR setup for MPLS/VPLS. I need to simply setup the 7206 to pass the MPLS/VPLS tagged packets to the next router on the link. We are using OSPF as the routing protocol. I am told by our Mikrotik guy that I just need to enable LDP and VPLS tunnels 4:0 on the 2 gig interfaces on the 7206VXR to let it pass the MPLS/VPLS traffic. It sounds simple but I'm not sure how to do this.
Any commands I need to imput to allow this router to pass this MPLS/VPLS traffic.
View 1 Replies
View Related
Apr 14, 2013
In studying and testing SSL VPN on an ASA I have the network as shown in the attached diagram. The configuration is based on an ASA with 8.3 but our ASA is 8.2 and at this time I'm not familiar with the new NAT configuration and commands in 8.3 or later and how to translate the 'nat (inside,outside) source static' for me to an 8.2 version.
View 3 Replies
View Related
Sep 25, 2012
I am looking to configure PBR in Nexus. The current setup in IOS is :
interface Vlan10
ip address 172.27.206.1 255.255.255.0
ip address 172.27.208.1 255.255.254.0 secondary
ip policy route-map Vlan_10_to_Corp
route-map Vlan_10_to_Corp permit 10match ip address Vlan_10_to_Corp
set ip next-hop 172.27.209.250!route-map Vlan_305_to_EFH permit 30
[code]....
But, Nexus PBR will not work with deny statements init. Now, what options do I have ?
View 2 Replies
View Related
Jul 27, 2012
i have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
View 3 Replies
View Related
Dec 14, 2011
How to, for the most part, setup 802.1x via wireless. I'm using two 5508 WLCs, and Cisco ACS. I will setup the user account/password information via Cisco ACS and User Identity and Hosts. I know from the WLC 5508 web admin tool that I can choose 802.1x in the security parameters. I only have a few question. We have two wireless networks, one is wide open and provides internet access, the other will provide internal access for select users. I am setting up 802.1x on the internal wireless lan. Do I need to configure any 802.1 configuration commands on the switch in order for this to work, if so where would be the locations to do this at? Also, if there is a MAC isolation configuration option I can configure to not allow other hosts on this specific wireless network to communicate with each other?
View 3 Replies
View Related
Jul 22, 2011
if there is document available for SNMP configuration for WLC 4404?
View 4 Replies
View Related
Aug 7, 2012
I am looking after a mixed collection of Cisco and HP switches and use a Perl script to extract configuration data.I use the ifStackStatus table (OID: 1.3.6.1.2.1.31.1.2.1.3) from RFC1573 to sucesfully obtain the EtherChannel data from the Cisco switches but, though I do obtain data from the same table from the Procurve switches it seems to bear no resemblance to Link Agregation. I could look at other tables and may have to - but would like to use this one in order to simplify the code.
View 2 Replies
View Related
Apr 7, 2013
We have an ASA with 8.4(5) version. we had detected that few ip's were getting shunned ,to overcome the problem no shun was used and the traffic normalised.But, the same problem re-occured a few days after that with logs showing traffic being shunned.
is there any fixed way to get rid of this. what commands can i use to verify related configuration on the firewall.
View 3 Replies
View Related
Mar 23, 2012
I want to know how to retrieve the complete configuration for a Nexus via the snmpwalk or snmpget commands...
View 6 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Dec 22, 2012
We have Cisco 4948 switches running in production. We want to moniter the trunk link through SNMP.If trunk link fails SNMP need to send notification to server.
View 1 Replies
View Related
Sep 10, 2012
I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
View 3 Replies
View Related
Feb 9, 2011
SSH is not working in Cisco 7206 VXR Router. I have configure
Hostname
Ip Domain name
Crypto key generate RSA
IN Line VTY 0 4
transport input preferred SHH
transport input telnet SHH
But stll it is not working. I am getting invalid crc recieved in packet.
Current IOS running is 12.3 (19) Enterprise 3des
View 3 Replies
View Related
May 12, 2011
I have two 7206 VXR routers with the VPN Service Adapter either side of a leased line (i.e. no provider between, pure layer two connectivity)A requirement is that traffic traversing the link is encrypted so I've configured an IPSec VPN between the two endpoints.During load testing we noticed a very severe performance hit when the VPN was enabled, disabling it again saw we were able to use almost 100% of the 1000Mbs line. The performance hit looks to be due to the increased MTU size when using IPSec, possible due to fragmentation.
I've read that the 7206 VXR can support 980Mbs (or there abouts) of throughput using AES providing the MTU size is 1400.Configuring this manually on each server in each data centre isn't feasible.As the link is effectively a point to point and we have control over the MTU size between the two routers, what options are available to increase the performance when the VPN is enabled?
View 1 Replies
View Related
Mar 2, 2011
I am attaching my current network topology, My problem is that i am having mpls & p2p link terminated on the 7206 router left side of diagram. now my problem is if i apply PBR on this 7206 router & tracer any host which are on right side of the diagram, it drops on IP 10.1.1.1..ideally it should go to my Core switch on right of the diagram.
View 8 Replies
View Related
Feb 24, 2011
I am having a Cisco 7406 VXR router. I want to know what is the max. MPLS link capacity that can be terminated on the link? We are planning to upgrade the MPLS link to 450 Mb..so was just wondering whether 7206 will support or not..
View 1 Replies
View Related
Mar 9, 2011
I have a problem in understanding how LLQ is implemented in different platforms of Cisco.QoS should kick in only when there is a congestion in the link irrespective of queueing / scheduling (LLQ and CBWFQ).But in certain platforms like GSR and IOS-XR, LLQ is confiugred only with priority and police command not with "prioirity percent <value>" command. In priority and police command since policer is used, LLQ is always on even there is no period of congestion. Of course with police you can re-mark the exceed traffic to different marking but thats not the requirement in my case.
In platforms like 7206, LLQ is configured with "prioirty percent <value>" which works ideally only when there is a period of congestion. When there is no congestion, LLQ class can use scanvenge other classes as well.Would like to know is there any specific reason why there is a difference in the implentation of LLQ between different platforms of Cisco.
View 1 Replies
View Related
Mar 14, 2012
I need to upload IOS c7200-advipservicesk9-mz.124-15.T16.binin 7206 NPE 400 router , As per cisco recommendation router should have DRAM : 256 MB ; Flash : 64I think my router contain only DRAM= 128 MB but not sure.
how much DRAM & Flash it contains.
Router1#sh versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2003 by cisco Systems, Inc.Compiled Thu 05-Jun-03 20:58 by dchihImage text-base: 0x60008954, data-base: 0x61E0C000
[Code].....
View 8 Replies
View Related
Mar 9, 2013
I'm getting below error on 7206VXR (NPE-G1) with IOS "c7200-js-mz.124-3i.bin".Attempt to use contiguous buffer as scattered.[code]
View 3 Replies
View Related
Mar 27, 2013
How can I enable Console port in 7206 vxr with NPE-G2 card installed, I need to use console from NPE G2 card.
The device turns on and status is also UP and I can also telnet to the device but I am not able to access the device through console port...
View 1 Replies
View Related
Oct 1, 2012
i did in past a lot of L2TP connection between two end point. in this case ans with 2911 series with ios 15 and DATA license Activated. the l2tp session does not establishe between a this 2911 and 7209. Attached is topology file and bellow the configuration of both router.
PE 2911
l2tp-class l2-dyn
authentication
password 123456
[Code]....
View 1 Replies
View Related
Mar 4, 2012
I have a lot of cisco 7206 vxr deviceses. I have a high cpu problem.I have a 7206 vxr g2. I used to use ebgp for three upstream carrier. I used to bgp full route table method. I have about 800 Mbps active traffics and behing the router about 1600 active customers.
How can I trouble shoot this high cpu problem?
#sh int gigabitEthernet 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is MV64460 Internal MAC, address is 000c.cf1d.d01b (bia 000c.cf1d.d01b)
Description: ***** GW Interface *****
[Code]....
View 4 Replies
View Related
Apr 24, 2012
In Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89%
PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process
1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter
[Code]...
View 11 Replies
View Related
Jan 18, 2012
I have a scenario with a Cisco 6506 and a 7206. The 6506 is running BGP and peers with our data center router. The 7206 is a stub router off the 6506 and is used as an edge router for customer T1 circuits. I want to use OSPF between the routers to exchange connected and static routes. The problem I have is that static BGP null routes on the 6506 are overriding the OSPF routes being received from the 7206. Example: The 6506 is advertising a class C network 192.168.1.0/24 to our data center. The 6506 does not utilize the 192.168.1.0/24 network. It is only used on the 7206 for customer T1 circuits and is carved up into /29 subnets. So the 6506 has a static route: ip route 192.168.1.0 255.255.255.0 null 0. Today the routing is accomplished with static routes on the 6506 for the 192.168.1.0 networks on the 7206. Using OSPF the 7206 advertises /29 links back to the 6506, but when I withdraw one of the /29 static routes from the 6506, the /24 null route takes precedence over the more specific /29 routes and the traffic is black-holed on the 6506. how can I get the OSPF routes to look preferable to the /24 null route on the 6506?
View 7 Replies
View Related
May 22, 2011
I would like to find out what the status is of the Cisco 7204 VXR and 7206 VXR routers?I understand they are EOLife and EOSale.Are they also EOSupport? we planning to upgrade 3 of them in our environment and management requires feedback around this.We thinking of going the ASR1000 route..
View 15 Replies
View Related
Jun 17, 2013
One of end costumers is trying to configure IP Accounting on 7206 running version 12.4(4)XD8,The issue we are having is that while the physical interface is up (the sub interface is part of a metro line which is directly connected) we dont see packets being accounted if the destination IP is down.
View 2 Replies
View Related
May 14, 2012
We have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests whcih comes from the client switch. Is there any feature or command which we can stop this?
View 4 Replies
View Related
Apr 4, 2012
I have an outside 7206 router that is configured with BGP. Behind that I have an ASA 5520 with a failover. Everytime my primary ISP goes down I have to failover the ASA to restablish a connection to the secondary ISP. When the primary comes back on line I have to fail it over again. I have had Cisco TAC look at the ASA and they didn't see anything misconfigured on the ASA. Doesn't seem to be any problems with the router config either.
View 11 Replies
View Related
Dec 5, 2010
What is the maximum number of multilinks we can have on a 7206 router ?
View 4 Replies
View Related
Mar 16, 2011
I have problem with the WAN Router 7206. It has been reloaded automatically 2 times since yesterday. [code] I have already put this message to the output interpreter and the solution is upgrading to the latest IOS. But, when I search in the Bug Toolkit about SegV problem, this bug status is still "Open". So, how can I upgrade to the latest IOS if the status of this bug is still open?
View 2 Replies
View Related
