I am having a Cisco 7406 VXR router. I want to know what is the max. MPLS link capacity that can be terminated on the link? We are planning to upgrade the MPLS link to 450 Mb..so was just wondering whether 7206 will support or not..
View 1 RepliesWe have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests which comes from the client switch.Is there any feature or command which we can stop this?
View 3 Replies View RelatedI want to configure multilink between two Cisco 7206 routers POS interfacesafter configuring both sides.Router 1interface Multilink5 ip address. [code]. I can see both sides through show cdp, also ospf process goes to FULL stateBut traffic is not flow between interfaces, and i can not even ping router's own ip address.When i delete network statement from ospf process, i can ping router's own interface and both routers can ping each other.
View 1 Replies View RelatedWhere can the following information be found?
1. CEF table capacity (maximum)
2. Route table capacity (maximum)
I can issue "show ip cef sum", "show ip route sum" to see the current usage.
I have a 1721 router with 3 equal routes to 0.0.0.0, using CEF for load balancing with universal load balancing algorithm. It doesn`t NAT, just routing. I wonder which is the maximum capacity of the router, since it should support up to 40000 connections to different destination IP. Is the limit set by the router resources (CPU, memory, ...) or a maximum limit of entries in the table FIB / RIB?
View 7 Replies View RelatedWhat is the maximum amount of traffic a 3825 router can take. I know that a 3825 is rated to handle half of a DS3/T3. We are planning to put a 50Mbps point to point metro Ethernet circuit between two 3825's and run encryption over that line. I just want to make sure we don't max out the router as I remember once a customer maxed out a 3825 with a ton or GRE tunnels and the router crashed every time they did their nightly data dump.
View 2 Replies View RelatedI have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 4 Replies View Relatedi have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 7 Replies View RelatedAny equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies View RelatedI am seeing the following log messages appear on our border edge 7600 router (SUP720-3BXL) The messages seem to appear when tag switching has been enabled on the interface, so somehow related I presume. The MPLS forwarding table is very small however. [code]
I can't see anything that is using up the ACL_TCAM HI BANK using "show tcam global acl" There aren't any ACL's applied to any of the interfaces, or policy-maps. The only ACL's in use are for SNMP, ntp, and VTY. These are very small any way. Interface Gi1/22, and 1/1 have tag switching enabled. [code]
The router has a full BGP routing table learned via an upstream (EBGP) peer neighbor, and an IBGP peer. The CPU utilisation seems fine, as is memory usage. CEF seems to be running okay. It's currently running [code] Are prefix lists part of TCAM? Is the router over-resourced holding a full bgp routing table?
I have been trying to understand from a long time about the throughput capacities of variety of Cisco Routers and Switches. Have searched over a million pages on cisco.com for data sheets/documents/etc. but havent succesfully got a single document highlighting all of what i need.
I have got queries on the below issues:Which model of Router can support upto 2Gig's of WAN Internet connection running BGP? Any list of routers and switches supporting variety of throughput's from 1 MB to 1 GB.I have heard some experts stating "Switches don't have throughput concerns as they switch the traffic and don't need to route traffic" How true is the statement?? and if it is, Why do we require 6500's instead of 3560 Distribution Switches.
Can LMS 4.1 give a report for port capacity in stack switches? We are starting to have issues where our techs are going out and plugging devices into switches and the switches are getting full. We would like to be able to see how many ports are left in each switch.
View 2 Replies View Relatedhow to measure the router or swith capacity?
Ex: Actually my problem is, i'm using Dlink 8 port switch, and 40 computers connected indirectly to that switch, few times getting issues like packet drops, internet connecting & disconnecting etc. so i want to know either the switch is capable or not.
I have a laptop and a PC, both connected to the same router, connected to a Time Warner Road Runner cable modem. The laptop works fine whether it is in wireless or wired mode. The PC does not have wireless. When the PC is connected to the router, it's download speed is OK but I have zero upload speed - which of course kills my ability to do almost any online or even LAN task, including browsing and file transferring over LAN.When I plug directly into the modem, bypassing the Belkin, the PC connection works just fine. It only encounters errors when going through the router, but every other computer in the household works fine through the router (3 laptops, work great either wired or wireless using same cables and ports as the PC). The PC worked fine in my old apartment with a different router, but as soon as I got to this one, nothing.
Both comp's have WinXP Home Edition. The PC has a Realtek onboard NIC, called PCIe GBE Family NIC in Device Manager. Have tried uninstalling and reinstalling it, and using multiple driver versions, to no avail. The Ethernet cable is known working. The router is a Belkin F5D9230-4 Wireless G Plus MIMO Router with fully updated firmware.All my firewalls are turned off, including that of the router.Everything is up to date, I have done full virus and malware scans, power cycled everything, and I just cannot solve this problem.
When enabling the WAN Traffic Meter on my RV180 with firmware 1.0.1.9, my download speed drops to half of my capacity.WAN Traffic Meter disabled: download around 13 MB/sec, WAN Traffic Meter enabled: max 6 MB/sec.WAN QoS is disabled!
View 1 Replies View RelatedWhen we list the available features for each license package on the cisco nexus licensing guide (page 5) [URL]
The N55-BAS1K9 provide unresitrcted OSPF routing capabilities. but on the Cisco web site they seen that the N55-BAS1K9 provide a limited (256 routes) learned via OSPF. N.B : the hardware plateforme is NX5K 5596UP with L3 Routing module 160Gbps.
How i can view the capacity throughput (backplane) of core switches (6509)? How i know much is in use?
View 2 Replies View RelatedReciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
SSH is not working in Cisco 7206 VXR Router. I have configure
Hostname
Ip Domain name
Crypto key generate RSA
IN Line VTY 0 4
transport input preferred SHH
transport input telnet SHH
But stll it is not working. I am getting invalid crc recieved in packet.
Current IOS running is 12.3 (19) Enterprise 3des
I have two 7206 VXR routers with the VPN Service Adapter either side of a leased line (i.e. no provider between, pure layer two connectivity)A requirement is that traffic traversing the link is encrypted so I've configured an IPSec VPN between the two endpoints.During load testing we noticed a very severe performance hit when the VPN was enabled, disabling it again saw we were able to use almost 100% of the 1000Mbs line. The performance hit looks to be due to the increased MTU size when using IPSec, possible due to fragmentation.
I've read that the 7206 VXR can support 980Mbs (or there abouts) of throughput using AES providing the MTU size is 1400.Configuring this manually on each server in each data centre isn't feasible.As the link is effectively a point to point and we have control over the MTU size between the two routers, what options are available to increase the performance when the VPN is enabled?
I am attaching my current network topology, My problem is that i am having mpls & p2p link terminated on the 7206 router left side of diagram. now my problem is if i apply PBR on this 7206 router & tracer any host which are on right side of the diagram, it drops on IP 10.1.1.1..ideally it should go to my Core switch on right of the diagram.
View 8 Replies View RelatedWhy Cisco implements so much switching capacity in their switches Obviously,16 Gbps of permutation performance is too much for the 8,8 Gbits (24*200+2*2000) needed by ports so why they put so many bandwidth?
View 3 Replies View RelatedI have a problem in understanding how LLQ is implemented in different platforms of Cisco.QoS should kick in only when there is a congestion in the link irrespective of queueing / scheduling (LLQ and CBWFQ).But in certain platforms like GSR and IOS-XR, LLQ is confiugred only with priority and police command not with "prioirity percent <value>" command. In priority and police command since policer is used, LLQ is always on even there is no period of congestion. Of course with police you can re-mark the exceed traffic to different marking but thats not the requirement in my case.
In platforms like 7206, LLQ is configured with "prioirty percent <value>" which works ideally only when there is a period of congestion. When there is no congestion, LLQ class can use scanvenge other classes as well.Would like to know is there any specific reason why there is a difference in the implentation of LLQ between different platforms of Cisco.
I need to upload IOS c7200-advipservicesk9-mz.124-15.T16.binin 7206 NPE 400 router , As per cisco recommendation router should have DRAM : 256 MB ; Flash : 64I think my router contain only DRAM= 128 MB but not sure.
how much DRAM & Flash it contains.
Router1#sh versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2003 by cisco Systems, Inc.Compiled Thu 05-Jun-03 20:58 by dchihImage text-base: 0x60008954, data-base: 0x61E0C000
[Code].....
I'm getting below error on 7206VXR (NPE-G1) with IOS "c7200-js-mz.124-3i.bin".Attempt to use contiguous buffer as scattered.[code]
View 3 Replies View RelatedHow can I enable Console port in 7206 vxr with NPE-G2 card installed, I need to use console from NPE G2 card.
The device turns on and status is also UP and I can also telnet to the device but I am not able to access the device through console port...
i did in past a lot of L2TP connection between two end point. in this case ans with 2911 series with ios 15 and DATA license Activated. the l2tp session does not establishe between a this 2911 and 7209. Attached is topology file and bellow the configuration of both router.
PE 2911
l2tp-class l2-dyn
authentication
password 123456
[Code]....
I have a lot of cisco 7206 vxr deviceses. I have a high cpu problem.I have a 7206 vxr g2. I used to use ebgp for three upstream carrier. I used to bgp full route table method. I have about 800 Mbps active traffics and behing the router about 1600 active customers.
How can I trouble shoot this high cpu problem?
#sh int gigabitEthernet 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is MV64460 Internal MAC, address is 000c.cf1d.d01b (bia 000c.cf1d.d01b)
Description: ***** GW Interface *****
[Code]....
In Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89%
PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process
1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter
[Code]...
I have a scenario with a Cisco 6506 and a 7206. The 6506 is running BGP and peers with our data center router. The 7206 is a stub router off the 6506 and is used as an edge router for customer T1 circuits. I want to use OSPF between the routers to exchange connected and static routes. The problem I have is that static BGP null routes on the 6506 are overriding the OSPF routes being received from the 7206. Example: The 6506 is advertising a class C network 192.168.1.0/24 to our data center. The 6506 does not utilize the 192.168.1.0/24 network. It is only used on the 7206 for customer T1 circuits and is carved up into /29 subnets. So the 6506 has a static route: ip route 192.168.1.0 255.255.255.0 null 0. Today the routing is accomplished with static routes on the 6506 for the 192.168.1.0 networks on the 7206. Using OSPF the 7206 advertises /29 links back to the 6506, but when I withdraw one of the /29 static routes from the 6506, the /24 null route takes precedence over the more specific /29 routes and the traffic is black-holed on the 6506. how can I get the OSPF routes to look preferable to the /24 null route on the 6506?
View 7 Replies View RelatedI would like to find out what the status is of the Cisco 7204 VXR and 7206 VXR routers?I understand they are EOLife and EOSale.Are they also EOSupport? we planning to upgrade 3 of them in our environment and management requires feedback around this.We thinking of going the ASR1000 route..
View 15 Replies View RelatedOne of end costumers is trying to configure IP Accounting on 7206 running version 12.4(4)XD8,The issue we are having is that while the physical interface is up (the sub interface is part of a metro line which is directly connected) we dont see packets being accounted if the destination IP is down.
View 2 Replies View RelatedWe have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests whcih comes from the client switch. Is there any feature or command which we can stop this?
View 4 Replies View Related