i have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 7 RepliesI have AIR-CT2504-5-K9, with 5 access point license support. I buy capacity adder license LIC-CT2504-5A for add 5 access points more. When i try download licence file from tftp server on WLC system i see message "License 1 Failed 1" on WLC. TFTP server message downloading OK.
View 4 Replies View RelatedI have a WLC 2504 with 5 AP licenses for which I have installed an adder license via GUI. The installation completed successfully, but I still cannot view the new license. The maximum number of APs is still showing as 5 and in fact I cannot add more that 5 APs. I tried installing the license file again, but now I get a "duplicate" error.
View 4 Replies View Relatedtell me when is available for order the High Availability for AIR-CT2504, like:
AIR-CT7510-HA-K9 Cisco 7500 Series High Availability Wireless Controller
AIR-CT5508-HA-K9 Cisco 5508 Series Wireless Controller for High Availability
When we list the available features for each license package on the cisco nexus licensing guide (page 5) [URL]
The N55-BAS1K9 provide unresitrcted OSPF routing capabilities. but on the Cisco web site they seen that the N55-BAS1K9 provide a limited (256 routes) learned via OSPF. N.B : the hardware plateforme is NX5K 5596UP with L3 Routing module 160Gbps.
I am installing a advance ip service licnese on cisco 861 router but it gives the following error message
Router#license install flash:FCZ143294BM_20110221232946625.licInstalling licenses from "flash:FCZ143294BM_20110221232946625.lic"Installing...Feature:advsecurity...Failed:% Error: Duplicate licenseInstalling...Feature:advipservices...Failed:% Error: Duplicate license0/2 licenses were successfully installed2/2 licenses were existing licenses0/2 licenses were failed to install
Router#
Also show ver shows the following
License Information for 'c860-data' License Level: advsecurity Type: Permanent Next reboot license Level: advsecurity
We are trying to upgrade throughput on ACE appliance 4710, getting below mentioned Error. We got license file from Cisco first license is for 0.5 to 1g, 2nd 1g to 2g and 3rd one is for 2g to 4g.
Our environment is critical, hence we are doing upgrade on Secondary appliance first. for that we are first isolating Secondary appliance by disabling up link switch port.
ACE-Shared/Admin# license install disk0:ACE20121016124306914.lic
Installing license... failed: Can't install this license with the current count
[code]...
"The license is invalid." (Error code:2268435460) it happens with all versions tested on several PCs (Win2003 Server, WinXP). Already tried to reboot, edit the registry, etc but no luck. Using 3 dcs 2121?
View 7 Replies View RelatedI have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
I have 8 2504 controllers and each needs to have a minimum of 20 MAC addresses added. I would rather not add them one at a time but I don't see any features that allow for an import. Any way to do the import?
View 2 Replies View RelatedWe have 1 WLC + 17 AP's on our main site and thats working fine... we just buyed a new AP for a new site of us. Its the same domain, same ip range nothing special at all... Somehow the AP on the site keeps rebooting and the users getting nervous of it there
Specs:
WLC: AIR-CT2504-K9
Software Version: 7.2.110.0
AP:AIR-LAP1042N-E-K9
Software version: 7.2.110.0
[code]....
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies View RelatedI configured a 2504 controller with two LWAPP Access Points, and I'm using two SSID's on the same controller, the problem is when the user tries to switch between SSID's he gets an error message saying that the other network is unavailable but if he disconnects from the first network and then connects to the other it works fine !.
View 5 Replies View Relatedsome computers is connecting to AP that is farthest, But there are two APS closer and the signal gets too low, the computer only connects to the closest AP if I disconnect and reconnect.I have 2 controllers series 2500 model AIR-CT2504-K9.
View 5 Replies View RelatedOn the WLC I've set DHCP address pool, everything seems fine after ap download image -> reboot -> hit "Enter" to start blar blar blar... however, after a few second the WLC will initial upgrade image again and again. it's like a non-stop process.
Attached is the start up message, as you can see, i captured it after the ap successfully boot up, and WLC initial another cycle of image upgrade.
btw, my network is flat, WLC & AP all in the same network.
*Nov 3 06:28:30.788: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
examining image...!
extracting info (292 bytes)
[Code].....
I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
City A is the data center with 2 WLC (CT2504-K9) and a number of AP. City B is a branch with MPLS between A and B. Right now the APs at City B has joined the controller. Users at B is getting ip's assigned from DHCP at City A. How do I configure the WLC so users can get ip's assigned from DHCP server present at B. Option 43 is enabled.
View 2 Replies View RelatedI've just been tasked with setting up 19 AIR-CT2504 WLCs with AIR-CAP3502E APs. The primary objective is to maximize throughput from clients uploading LARGE files over the air.
I need to make sure I config HT 802.11n properly with no support for legacy clients in the 5Ghz band.
I have inherited a site where the builders have installed a 2504 controller with 8 access points. Unfortunately they have not created an ap-manager interface when they did the set up. Is there any way I can do this via GUI or command line without going back to defaults?
View 7 Replies View RelatedI am using two AIR-CT2504-K9 controllers
Product Version.................................. 7.4.100.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
and 20 access points AIR-CAP2602I-E-K9 Cisco IOS Software, C2600 Software Version 15.2(2)JA, RELEASE SOFTWARE (fc1) LWAPP image version 7.4.100.0
I created 3 SSID:
1. [WPA2][Auth(PSK)]
2. Web-Passthrough
3. [WPA2][Auth(PSK)]
Configuration on controllers is identical. High Availability is configured on all APs. First controller controls only those APs witch have SSIDs with [WPA2][Auth(PSK)], second controller is basically for APs with Web-Passthrough SSID. From the start I have problem, some clients who try to connect to SSID with PSK are dropped or can’t connect entirely, but when they go to the next AP they connect successfully. For example I have Android smartphone and Lenovo laptop, smartphone connects successfully but laptop fails connection to the same AP, but when I take it to other AP it connects successfully. Sometimes smartphones can’t connect too. When devise can’t connect to one SSID it can’t connect to other SSID either. Sometimes there are up to 20 clients tying to connect to the same AP.
When I look into logs, I get these two messages:
Jun 3 08:58:58 192.168.224.1 WLC1: *dot1xMsgTask: Jun 03 08:58:51.176: #DOT1X-4-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:456 Max EAPOL-key M1 retransmissions exceeded for client 7c:e9:d3:f4:74:4d
[Code].....
I've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
We have just installed our first CT2504.After install I have found a dramatic drop in signal strength compared to the wireless survey result obtained.All of our site surveys include real world testing using an AP, in this case a AP1041N.In doubt I retested a section using an AP1041N in the same location as one of the recently deployed LAP1041N.
In the same location a LAP1041N has between -10 and -20dbi difference in SNR compared to the test AP1041N.For example locations that tested with -60dbi using an AP1041N have little to no coverage using the LAP1041N installed.This applies irrespective of the WLC automatic control over Tx power or manually setting the LAP TX to the highest level.
I have a CT2504 at a customer site which does not load the captive portal page correctly nor will it load via HTTP as opposed to HTTPS.So for starters I did what I do with all my CT2504's (which work fine), I configured my Guest network to authenticate via the default captive portal. I then disabled HTTPS and SSH and enabled HTTP managment followed by rebooting the controller. On boot, logging into the WLC management GUI is automatically presented via HTTP as expected.However when clients access the Guest network they are redirected to the Web Authorisation via HTTPS instead of HTTP?In addtion to the above the captive portal page does not display correctly.The preview via the controller works fine, but the client is presented with a page with broken links to the images i.e. the blue strip at the top and the Cisco logo on the right.
View 3 Replies View RelatedI´m trying to connect them to my WLAN, for throubleshoot I create a new WLAN with WPA2-TKIP and a PSK, the devices didin´t connect to the WLAN.I also change the security to WPA2-AES with TKIP, it didn´t work too.
My best choice was to disable every security configuration in order to began the throubleshooting from zero, but even with no Layer 2 and 3 security, the devices didn´t connect to my Test WLAN.
I´m using a AIR-CT2504-K9 WLC with two AIR-CAP3502I-A-K9 AP, all the PCs and other brand cellphones and tablets work well.
Also I have a SOHO router on the office, and the IPad connect without a problem with that WLAN, but I need them to connect to my Cisco AP.
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedReciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
I am having a Cisco 7406 VXR router. I want to know what is the max. MPLS link capacity that can be terminated on the link? We are planning to upgrade the MPLS link to 450 Mb..so was just wondering whether 7206 will support or not..
View 1 Replies View RelatedWhere can the following information be found?
1. CEF table capacity (maximum)
2. Route table capacity (maximum)
I can issue "show ip cef sum", "show ip route sum" to see the current usage.
I have a 1721 router with 3 equal routes to 0.0.0.0, using CEF for load balancing with universal load balancing algorithm. It doesn`t NAT, just routing. I wonder which is the maximum capacity of the router, since it should support up to 40000 connections to different destination IP. Is the limit set by the router resources (CPU, memory, ...) or a maximum limit of entries in the table FIB / RIB?
View 7 Replies View RelatedWhat is the maximum amount of traffic a 3825 router can take. I know that a 3825 is rated to handle half of a DS3/T3. We are planning to put a 50Mbps point to point metro Ethernet circuit between two 3825's and run encryption over that line. I just want to make sure we don't max out the router as I remember once a customer maxed out a 3825 with a ton or GRE tunnels and the router crashed every time they did their nightly data dump.
View 2 Replies View RelatedAny equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies View Related