Cisco Wireless :: WLC CT2504 / Interface IP Cannot Be Used As Internal DHCP Server IP
Apr 5, 2012
I've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
View 1 Replies
ADVERTISEMENT
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
May 7, 2012
I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching. - I have an LWAP connected to the WLC in HREAP mode. - WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server. - Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the V LAN configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name............. Cisco Systems Inc.Product Name................ Cisco Controller Product Version................. 7.0.116.0Bootloader Version................ 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version..... FPGA 1.3, Env 1.6, USB console 1.27Build Type.......... DATA + WPS + LDPE
[code]...
View 12 Replies
View Related
Jul 21, 2012
A client wants us to use the internal DHCP server on a 5508 instead of Windows DHCP. They will have 15 APs initially and upto 25 later. The docs on the 7.2 WLC make it sound like this is discouraged: Internal DHCP Server.
The controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller.
In this case, the APs will not be in the same subnet as the Managment Internet.Is it a mistake to use the internal DHCP with upto 25 APs (3 WLANs)?
View 3 Replies
View Related
Mar 25, 2013
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
View 3 Replies
View Related
Apr 8, 2008
I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
Every time I try to apply the configuration I get an "error in setting DHCP scope network and netmask".
I've tried using:
192.168.2.10
192.168.2.255
192.168.2.254
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
I was assuming they meant the interface for the guest vlan.
View 3 Replies
View Related
Jan 12, 2012
How to clear dhcp lease in WLC 6.0.199 from the IP leased from internal server?
View 1 Replies
View Related
Apr 16, 2012
City A is the data center with 2 WLC (CT2504-K9) and a number of AP. City B is a branch with MPLS between A and B. Right now the APs at City B has joined the controller. Users at B is getting ip's assigned from DHCP at City A. How do I configure the WLC so users can get ip's assigned from DHCP server present at B. Option 43 is enabled.
View 2 Replies
View Related
Jan 23, 2013
I have inherited a site where the builders have installed a 2504 controller with 8 access points. Unfortunately they have not created an ap-manager interface when they did the set up. Is there any way I can do this via GUI or command line without going back to defaults?
View 7 Replies
View Related
Apr 23, 2012
I have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies
View Related
Feb 16, 2011
Started this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
View 3 Replies
View Related
Nov 7, 2012
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies
View Related
Aug 2, 2012
I'm running a system that requires a third (and potentially fourth) DHCP server to be setup on each network in my network. The first two devices are Windows DHCP servers serving IPs from different address ranges for failover. The third DHCP is just a listener to receive OS information and device names to be logged in a database.
Currently this works like a charm for my wired clients as I can add in the third and fourth ip helper-address on each vlan and the information is received by the listeners. However, I cannot find anywhere in my WLC5500 to setup these extra two DHCP helper addresses.
The wireless vlan on my layer 3 switch has all the ip helper-addresses, but this doesn't seem to work, and the devices just use the DHCP servers set on the interface in the WLC.
View 5 Replies
View Related
May 9, 2012
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies
View Related
Feb 23, 2012
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
View 7 Replies
View Related
Aug 22, 2011
The two controllers are having two internal DHCP servers with the same range in LAN (enx1,enx2). but i have specified which is primary DHCP server(enx3) in WLAN interface.
Now if a new user added into network, will he get IP address from primary dhcp(WLC) or AP connected WLC.
if two users connected to 2 diff AP's which are connected to 2 WLC will get the same IP address? since having same address pool configured.
View 11 Replies
View Related
Nov 25, 2012
I am wondering if the folowing is a valid configuration:
WLC2504
AP2600
I need 3 SSID/VLAN, 1 for corporate devices, 1 for coporate smartphones, 1 for guest.
Port 1 on the 2504 should be used for management and corporate devices and connect to the corp network. Port 2 is for smartphones/guest and will be connected to a Cisco ASA 5515 that is connected to a second ISP.
Corp devices should get IP from an Windows DHCP. Smartphones/guest should get IP from the WLC. Is this possilbe? I read this in a document "To use the WLC as a dhcp, you need to enable DHCP proxy as it is required." Some how I am imagining that this will mess with the Windows DHCP. Is it better to use the ASA as DHCP for smartphones/guest?
View 4 Replies
View Related
Jun 28, 2012
We created the management interface, an internal DHCP scope in same subnet, and Two SSID tied to the same management interface:
- when we connect to the first SSID we have and IP address
- but when we connect to the secone SSID: impossible to get an ip address - auth and association are OK
View 11 Replies
View Related
Nov 29, 2011
I have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
View 1 Replies
View Related
Sep 27, 2012
I recently installed 2 wlc 5508 with the latest software 7.3.101.0. I am not able to activate the Internal DHPC Server. The following message appears: "Error in setting dhcp scop leasetime".
View 5 Replies
View Related
Jun 13, 2012
DHCP conflict on 881-W with the internal AP?I have (12) 881-W chassis in the field. They are running DHCP services to the wired users as well as to the internal AP for reachability / management / etc. The scope for the internal AP is a /30 so only one address is in the scope and it is intended for the internal AP. This serves a a point to point link between the internal AP and the internal Router inside the 881-W chassis.
Somehow the 881-W DHCP server is getting out of synch and a conflict is occurring. It seems at some point, either at boot-up or lease expiration/renewal, the DHCP server is performing a ping to verify that the address is not in use. The AP has this address assigned prior and replies to the ping causing a conflict. I noticed an AP down today, checked the 881-W uptime and the conflict correlates to the same time. I have to manually clear the conflict and everything works as it should.The existing 12 881-w's could grow to 100's over time, so the manual intervention of clearing the conflict is not going to scale. I really want to stay away from static reservations.
View 1 Replies
View Related
Dec 14, 2009
I just bought a Linksys 320N router to replace another competitors router. I am trying to connect to my VPN server from outside my network. I have the external ip to my network. I setup the new 320N router just like the old router. set dmz ip to internal ip of vpn server, set port forwarding to 1723, both, internal ip of vpn server, I have a way to test the vpn while i am inside my network. So, I can watch the VPN server log and see the request come into the server and it times out with the Linksys 320 N hooked up. If I have the old router hooked up, the vpn establishes a connection.
View 9 Replies
View Related
Sep 13, 2012
I had an Linksys WRT54GS and this wireless is connected to a switch in an internal enviroment but i want connect guest users without them see my internal network and can't access to any internal server....how can i configure this?
View 1 Replies
View Related
Nov 30, 2011
I've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
View 4 Replies
View Related
Oct 11, 2011
I have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
View 7 Replies
View Related
Oct 19, 2011
I've a question about VPN IPSEC on ASA5510
In the LAN network , we use a DHCP on a Windows2003Server. Is it Possible to Configure the remote VPN Clients to use this DCHPserver throughout the VPN IPSEC and Assigned Automatically IP when the connection is done?
View 1 Replies
View Related
May 6, 2012
How do Mobility Groups work with internal DHCP scopes on a WLC 5508?We have a WLC 5508 with two internal DHCP scopes which redirect to captive portals for authentication. I am looking at putting in a second WLC in a mobility group setup to provide some WLC redundancy. The LWAPs will be setup so that every second AP is on the has the second WLC as its primary controller. If the primary WLC fails we want the secondary to be able to take over and issue IP's from the internal scope. How do you set this up with a Mobility group so the second WLC does not act as a rouge DHCP server while the primary WLC is still active?
View 6 Replies
View Related
Jan 29, 2011
When I click on "DHCP Reservation" button in the web interface of the E3000 I don't see any information about the current devices and the reservation list.This problem occurs when my sattelite reciever tries to get an IP address from the DHCP.the name of the receiver is "dream box" (no special characters).I didn't have any problem in the past with my previous router (3COM)Since there are error messages in the page (screenshot is attached), I've tried to use different browsers but the result was the same (Firefox, Safari, IE 8)
View 9 Replies
View Related
Jun 5, 2013
I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
View 2 Replies
View Related
Aug 8, 2012
I have 8 2504 controllers and each needs to have a minimum of 20 MAC addresses added. I would rather not add them one at a time but I don't see any features that allow for an import. Any way to do the import?
View 2 Replies
View Related
Nov 4, 2012
We have 1 WLC + 17 AP's on our main site and thats working fine... we just buyed a new AP for a new site of us. Its the same domain, same ip range nothing special at all... Somehow the AP on the site keeps rebooting and the users getting nervous of it there
Specs:
WLC: AIR-CT2504-K9
Software Version: 7.2.110.0
AP:AIR-LAP1042N-E-K9
Software version: 7.2.110.0
[code]....
View 4 Replies
View Related
May 17, 2012
I am currently managing an ASA5510 using ASDM through the management port but I would like to manage the ASA through the internal port.
My concern is that I thought I remembered reading someplace that if you setup an internal port for management that it can't be used for anything else. Is this correct?
I only configured one internal port and it is the path to my LAN. I would hate to configure the port for management only to find that I disconnected my firewall from my internal network in the process. Can I use my one and only configured internal port for both ASA management and route from my LAN thru the ASA firewall?
I currently have the management port set to 192.168.1.1 and my internal interface is 10.1.1.1. If I open ASDM and connect thru the management port and select Configuration/Device Management/Management Access/ASDM/HTTPS/Telnet/SSH
select "ADD"
select access type "ASDM/HTTPS"
select interface "internal"
IP Address "10.1.1.0"
Mask "255.255.255.0"
Will that give me access to ASA management thru my internal network but cripple my network access to the ASA?
View 6 Replies
View Related
Apr 4, 2012
AIR-CT2504-25-K9 will support AIR LAP1142N-E-K9
View 3 Replies
View Related
