I've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
View 4 Replies
I have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
View 7 Replies View RelatedLately, Ive been trying to change my router DNS to OpenDNS. Somehow, after changing it, I couldnt access the router page at 192.168.0.1, getting the error 500 message. I unplugged and plugged the router with no effect. Im using a dlinkddns.com dynamic IP, and have a few ports forwarded for my DVR. The router model is DIR 615. want to change the DNs for speed and filtering purposes.
View 4 Replies View Relatedi'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies View RelatedJust bought first wireless router, when i insert CD and start setup, after a few seconds i get Error 301: internal error. i have rebooted and still no luck. I've tried going to 192.168.1.1, i got in one time but didn't understand half the stuff. now i can't go back into that page.
View 8 Replies View Relatedmy laptop sometimes gives a 500 internal server error when I try to go to any website. our other wireless devices such as our phones don't do this while the laptop is.
View 2 Replies View RelatedI just bought a Linksys 320N router to replace another competitors router. I am trying to connect to my VPN server from outside my network. I have the external ip to my network. I setup the new 320N router just like the old router. set dmz ip to internal ip of vpn server, set port forwarding to 1723, both, internal ip of vpn server, I have a way to test the vpn while i am inside my network. So, I can watch the VPN server log and see the request come into the server and it times out with the Linksys 320 N hooked up. If I have the old router hooked up, the vpn establishes a connection.
View 9 Replies View RelatedI had an Linksys WRT54GS and this wireless is connected to a switch in an internal enviroment but i want connect guest users without them see my internal network and can't access to any internal server....how can i configure this?
View 1 Replies View RelatedI was given the above router but I need set up software?
View 1 Replies View RelatedPlugging in laptop to ethernet 1, no IP obtained. ethernet 2, 3 and 4 give me an IP (192.168.1.100) but I can't ping the linkys. Holding the reset button has not done anything. I can connect and manage the Linksys wirelessly. I've tried re-flashing firmware and resetting factory defaults. Ethernet 1 LED is always on connected or not. The other three light when connected.
View 4 Replies View RelatedI'm trying to take off the strict nat restriction.
View 1 Replies View RelatedI just moved in with my friend and i'm having trouble connecting to wireless router linksys WRT54GS2 V1. My roommate can connect his laptop and desktop to the router wirelessly, but my iphone and laptop can't connect. I've tried both of my devices on a wireless network at a friend's house, and both worked fine. We even changed AND removed the password and it doesn't let me log on the internet.
View 5 Replies View RelatedMy router randomly stopped working after I bumped into the wire. It still shows up as a network you can connect to, but whenever I try to connect, it keeps saying there is a problem with my connection. I tried using a different internet cord, but nothing changes. I even tried to reinstall my router and still no dice.
View 6 Replies View Relatedhow to change the password for my wifi.
View 1 Replies View RelatedI have a Linksys model WRT54GS2 with 4 ports, with Ethernet cables connected to ports 1 and 2. I have a laptop connected by wireless connection, with only an Xbox connected using Port 1 and occasionally port 2. Just recently, port 1 shows no activity. When connected to Xbox it doesn't display a check mark showing connection but does with port 2. I've connected it to port 3 and 4, which shows a check mark but won't connect to Xbox live. It's like port 2 only works, what I can do to "fix" ports 1, 3, and 4?
View 1 Replies View RelatedI've been having trouble with my wrt54gs2 and 4 360's. I tried a link someone posted for me to a cisco tutorial, it worked, but only for one 360. I have a Netgear wndr3400, I HATE the wireless on that router. Its unreliable but I like the features, the guest network and transfer meter, plus its worked with 4 360's out of the box. So would it be possible to turn off my wifi on the Netgear and plug the wrt54gs2 in and use its wireless?
View 7 Replies View RelatedSo I have been having internet problems lately and first thought it was my modem. Figured out it wasn't the modem but the isp.After I woke up the next morning I found the wireless not to we working again but the hard connection to be just fine. I have tried resetting the router but I'm not entirely sure I went through. The orange light no longer comes on. Wired connection also doesn't work while connected to the router. I have tried 192.168.1.1 and nothing loads. The router and modem are about 5 or 6 years old. A windows xp desktop, windows 7 and vista laptops are on the network with a blue ray player.the router is a wrt54gs2 v7
I think i have to reconfigure the router but I'm not sure. If that's the case why am i having trouble with 192.168.1.1?
I have a Linksys WRT54GS2 router, a PC (Windows XP) and a laptop (Windows 7 Ultimate 32 bit).I have been using this router for 3 months. I was able to use the internet on both devices simultaneously until now. But suddenly since yesterday it only works for one device at a time, not both.
If I connect to the router then I can access the internet only from the laptop. To use the internet from the PC, I have to power off the router, type in run "netsh int ip reset resetlog.txt", and restart the PC. But as the router is off, the internet is inaccessible on the laptop.
While router is on, the PC shows limited or no connectivity.
I tried reseting the router 2-3 times.
On the laptop it sometimes shows "IP address conflict has been detected", even though the IP addresses of the devices were not the same. The IP address of the PC shows 169.X.X.X (when the router is on), whereas the ISP's IP addresses start with 124.X.X.X.
I have an E1200 and am time out and packet loss issues. The internet connection is fine for 30 seconds to five minuets and then everything times out for 15-20 seconds. Although it’s only a minor incontinence to web browsing, it makes playing games and watching videos a nightmare. “Lost connection to server error.” and the like…
I upgraded to a new router, the e1200 I am currently using, from my Tenda 10/100 N. The problems where the same that I am experience currently and the reason I bought it in the firs place.When I directly connect to the cable modem, I have no issues and everything is fine.I have run a trace route and the second hop, (the router to the modem) is the choke point.I have cloned the MAC address.I have updated the firmware and hard reset
I have throttled my MTU to automatic, 1500, and 1472. None making any difference.I have disabled NAT and all that does is kill my internet connection.I have disabled all firewalls router and windows, no change.I replaced the physical wire from the router to the modem.I have disconnected all devices except one computer, and no difference.I ran a DNS trace and I have… non routable local internet address 192.168.1.1 DNS-cac-lb-01.rr.com and DNS-cac-lb-02.rr.com.I am using windows 7 and my ISP is time Warner so-cal.
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies View RelatedI have a linksys WRT54GS2. I forgot my password, so I pushed the little reset button. I reset the router and had to configure it all again. I thought it had it configured, because you can see the router name on the "view networks" page, but it just doesn't connect for some odd reason. What could this reason be? I have my router password protected, and I am sure I typed in the correct password.
View 8 Replies View RelatedCurrently I have an ASA setup as a Firewall with 1 outside interface and 2 inside interfaces. Initially, the Guest interface was setup to receive DHCP from the ASA and everything was working. I'm adding router and a server for the guest interface and what I'm trying to accomplish now is the following: ASA 5505 > Airport Extreme with a public static IP (69.xx.xx.6), handling DHCP and NAT > Mac Server as DNS Server.Right now, when I connect to my Airport Extreme with any computer, I don't have internet. I don't understand what's wrong. My DNS Server has a reserved IP address: 192.168.226.2 and it's pointing to itself and forwarding the ISP DNS servers, the Airport Extreme is handling the DNS Server IP and the ISP DNS Server IP but I can't connect to the internet from the server. [code]
View 31 Replies View RelatedI am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching. - I have an LWAP connected to the WLC in HREAP mode. - WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server. - Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the V LAN configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name............. Cisco Systems Inc.Product Name................ Cisco Controller Product Version................. 7.0.116.0Bootloader Version................ 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version..... FPGA 1.3, Env 1.6, USB console 1.27Build Type.......... DATA + WPS + LDPE
[code]...
A client wants us to use the internal DHCP server on a 5508 instead of Windows DHCP. They will have 15 APs initially and upto 25 later. The docs on the 7.2 WLC make it sound like this is discouraged: Internal DHCP Server.
The controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller.
In this case, the APs will not be in the same subnet as the Managment Internet.Is it a mistake to use the internal DHCP with upto 25 APs (3 WLANs)?
On ACS 4.2.0.124 version installed on Appliance 1113.We are getting error code as "Internal error" and also "Enabling Tacacs+ is not allowed for this Access Server" while client authentication.
View 5 Replies View RelatedI have a e4200 sitting behind a BT home hub 2. The home hub provides internet connection to the e4200, and the e4200 allows all devices to connect. I am able to ping internal IP addresses, but when I try to ping by device name it returns the external IP address. How can I view / amend the DNS table on the router?
View 9 Replies View Relatedsetup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
Every time I try to apply the configuration I get an "error in setting DHCP scope network and netmask".
I've tried using:
192.168.2.10
192.168.2.255
192.168.2.254
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
I was assuming they meant the interface for the guest vlan.
How to clear dhcp lease in WLC 6.0.199 from the IP leased from internal server?
View 1 Replies View RelatedI've got a new CT2504 controller with software version 7.0.220.0 Regarding to [URL]I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3 vlan401 Interface IP can not be used as internal DHCP server IP It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
[code].....
I recently installed 2 wlc 5508 with the latest software 7.3.101.0. I am not able to activate the Internal DHPC Server. The following message appears: "Error in setting dhcp scop leasetime".
View 5 Replies View RelatedI'm working on a Dell Vostro 220s running Windows XP with an integrated NIC. It had a few hundred viruses on it and after removing them, I can't get an internet connection. The icon says connected with 0 packets sent and 0 packets received. DHCP is enabled and other computers on the network can connect to the internet. The drivers are installed and detected as working properly. I have rebooted also, with no luck. Ipconfig fails with the error "An Internal error occurred: The request is not supported."
View 8 Replies View RelatedI have an E3000 router, 2 computers connected via wires, and a PS3, airport express, laptop, and a few other devices which connect wirelessly. I've been having intermittent difficulties with specific services disappearing within my network. From time to time, some of the services which run across the network stop working; The Airport disappears (cannot contact it via airport utility or see it as an airplay destination), and the Playstation stops being able to contact media server running on wired computer. When this occurrs, all devices are still able to connect to the internet, and I am even able to copy files between a hard wired computer and laptop via CIFS (windows file sharing) protocol. Power cycling the E3000 solves this; the airport reappears, the PS3 can once again see the media server running on the PC, etc.
View 2 Replies View Related
