Linksys WRT54GS2 Router - Wireless Internet Not Working With Two Devices Simultaneously?
Aug 2, 2012
I have a Linksys WRT54GS2 router, a PC (Windows XP) and a laptop (Windows 7 Ultimate 32 bit).I have been using this router for 3 months. I was able to use the internet on both devices simultaneously until now. But suddenly since yesterday it only works for one device at a time, not both.
If I connect to the router then I can access the internet only from the laptop. To use the internet from the PC, I have to power off the router, type in run "netsh int ip reset resetlog.txt", and restart the PC. But as the router is off, the internet is inaccessible on the laptop.
While router is on, the PC shows limited or no connectivity.
I tried reseting the router 2-3 times.
On the laptop it sometimes shows "IP address conflict has been detected", even though the IP addresses of the devices were not the same. The IP address of the PC shows 169.X.X.X (when the router is on), whereas the ISP's IP addresses start with 124.X.X.X.
View 1 Replies
ADVERTISEMENT
Mar 8, 2012
My router randomly stopped working after I bumped into the wire. It still shows up as a network you can connect to, but whenever I try to connect, it keeps saying there is a problem with my connection. I tried using a different internet cord, but nothing changes. I even tried to reinstall my router and still no dice.
View 6 Replies
View Related
Jun 3, 2012
So I have been having internet problems lately and first thought it was my modem. Figured out it wasn't the modem but the isp.After I woke up the next morning I found the wireless not to we working again but the hard connection to be just fine. I have tried resetting the router but I'm not entirely sure I went through. The orange light no longer comes on. Wired connection also doesn't work while connected to the router. I have tried 192.168.1.1 and nothing loads. The router and modem are about 5 or 6 years old. A windows xp desktop, windows 7 and vista laptops are on the network with a blue ray player.the router is a wrt54gs2 v7
I think i have to reconfigure the router but I'm not sure. If that's the case why am i having trouble with 192.168.1.1?
View 3 Replies
View Related
Apr 12, 2013
I was given the above router but I need set up software?
View 1 Replies
View Related
Aug 29, 2012
Plugging in laptop to ethernet 1, no IP obtained. ethernet 2, 3 and 4 give me an IP (192.168.1.100) but I can't ping the linkys. Holding the reset button has not done anything. I can connect and manage the Linksys wirelessly. I've tried re-flashing firmware and resetting factory defaults. Ethernet 1 LED is always on connected or not. The other three light when connected.
View 4 Replies
View Related
Mar 26, 2012
I'm trying to take off the strict nat restriction.
View 1 Replies
View Related
Jul 9, 2011
I just moved in with my friend and i'm having trouble connecting to wireless router linksys WRT54GS2 V1. My roommate can connect his laptop and desktop to the router wirelessly, but my iphone and laptop can't connect. I've tried both of my devices on a wireless network at a friend's house, and both worked fine. We even changed AND removed the password and it doesn't let me log on the internet.
View 5 Replies
View Related
Nov 30, 2011
I've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
View 4 Replies
View Related
Mar 26, 2013
how to change the password for my wifi.
View 1 Replies
View Related
Mar 23, 2012
I have a Linksys model WRT54GS2 with 4 ports, with Ethernet cables connected to ports 1 and 2. I have a laptop connected by wireless connection, with only an Xbox connected using Port 1 and occasionally port 2. Just recently, port 1 shows no activity. When connected to Xbox it doesn't display a check mark showing connection but does with port 2. I've connected it to port 3 and 4, which shows a check mark but won't connect to Xbox live. It's like port 2 only works, what I can do to "fix" ports 1, 3, and 4?
View 1 Replies
View Related
Sep 1, 2011
I've been having trouble with my wrt54gs2 and 4 360's. I tried a link someone posted for me to a cisco tutorial, it worked, but only for one 360. I have a Netgear wndr3400, I HATE the wireless on that router. Its unreliable but I like the features, the guest network and transfer meter, plus its worked with 4 360's out of the box. So would it be possible to turn off my wifi on the Netgear and plug the wrt54gs2 in and use its wireless?
View 7 Replies
View Related
Jun 10, 2012
It started happening back in around November, my sister and my computer would start freezing occasionally, slurring the audio into a robotic sound, eventually to come to.It gradually got worse, and I assumed it was a graphics card problem since it would freeze ONLY SOMETIMES and say that the graphics driver stopped working and has recovered. It usually didn't say that, though.Lately though, I noticed that when it would freeze sometimes the internet would go out for some connected devices, such as the Xbox 360. The only computer that was NEVER affected by this is the one connected directly by Ethernet to the Netgear router, (every other device is WiFi.)
Sometimes even, my sister and mine would freeze simultaneously. It was a sort of rare occurrence, though.I very lately started to notice that it would freeze when trying to load internet components with larger amounts of data, such as server console logs, Flash videos, and Soundcloud players. What threw me off is that it would sometimes freeze in programs like FL Studio or Windows Media Player... It's possible I guess that the programs were unrelated and what caused the freeze is SOMETHING sending/receiving corrupt packets.
View 6 Replies
View Related
Jul 23, 2011
Router 1: I have a WRT120N wireless router connected to the Internet. It has IP 192.168.1.1 and DHCP is enabled with address range 192.168.1.100 up.
Router 2: I have a WRT310N router connected to the LAN via LAN port to ethernet jack in the wall (not WAN/Internet port). It has ip 192.168.1.2 and DHCP is DISABLED.
All the devices on my network can see each other. Devices connecter to router 1 can see devices connected to router 2.The problem is, devices connected to router 2 cannot get to the Internet. I verified clients connecting to router 2 are assigned the same DNS addresses and the same gateway 192.168.1.1 as the clients connected to router 1. But for some reason router 2 doesn't know how to router Internet traffic out through router 1?
I tried plugging the LAN cable into the Internet/WAN port on Router 2 but then devices on Router 2 can no longer see devices on Router 1. I've seen discussions of setting up router 2 on its own subnet: 192.168.2.1 instead of 192.168.1.2 but then supposedly devices on router 2 will still not be able to see devices on router 1.
I'm guessing router 2 can't access the Internet because it is default configured to send Internet traffic to the Internet port, no t the LAN port. how to configure it so all devices on both routers see each other and router 2 devices can get to the Internet.
View 3 Replies
View Related
Apr 18, 2013
I am looking to track what my kids are doing on the internet. I have an ea4500 and was wondering if there is a detailed log file that I can look at?
View 3 Replies
View Related
Apr 21, 2013
My E3000 has been working fine with 1.0.04 build 6 FW. Recently some devices (kindle, iPad) can't connect to internet while connected to E3000 via WiFi network. Had a look my E3000 router IP is 192.168.0.1 but those problematic devices has IP 192.168.1.XXX allocated by DHCP not sure why. Currently I manually set up static IP 192.168.0.XXX for those devices.
View 1 Replies
View Related
Apr 18, 2010
I have a disconnecting problem with my WRT120N (Linksys) wireless router. Sometimes all wireless devices lose the connection to the internet, and the access to the router administration page (192.168.1.1) becomes impossible. In this case LEDs of power, internet and wireless are lighting without flashing. This problem usually occurs every 48 hour, and there was no way to make a reconnection except turning the router off by unplugging the power wire and plug it again…
I hope find a solution for this problem here
Other question: are there any problems in Firmware Version: v1.0.04
Note: currently I use Firmware Version: v1.0.01
View 9 Replies
View Related
Dec 25, 2011
My PC will connect just fine, but it is the only device on my network that the router will allow internet access. The router will allow other devices (DVR, laptop, nook) to connect to it, but won't allow those devices to connect to the internet. Each device will show the same error, - "connected to linksys - no internet". I've reset the router many times with no results.
View 1 Replies
View Related
Jan 4, 2013
I was attempting to use my EA4200 in bridge mode but found out for some reason my devices weren't connecting to the internet. So I decided to try to access the router through the IP address of the router with no avail. So I pull the router and plug it in normally and notice that it keeps flashing. So that already gives me an idea something is wrong. I go through the process of unplugging everything from the router, and plugging my PC directly into the LAN port 1 of the router then powering it up. On my network connection list it keeps trying to identify the network but keeps failing (keep in mind that the router still is flashing). So I decide to attempt a 10 second reset, then a 30 second, then a 30-30-30. All with no success. The router keeps flashing.
Which gets me to the point where I am now... router flashing at me, and wondering if this now out of warrenty unit was a waste of money. I am noticing that a lot of people have had questions and issues with the E4200v2 which now concerns me, well hopefully this can be fixed.
View 9 Replies
View Related
Aug 15, 2011
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies
View Related
Jul 10, 2012
Reciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
View 1 Replies
View Related
Nov 27, 2011
My PC running on Windows 7.I'm connected Internet via Wireless adapter. [code] But after connect VPN i'm not able to connect Internet anymore. I think because there are 2 gateway in there. and the default gateway become vpn network. In my case. How to connect vpn client and internet wireless adapter simultaneously?
View 1 Replies
View Related
Aug 14, 2012
I know that the C3KX-NM-10GT network module has two (copper) ports that support speeds of 1Gps or 10Gps. Could this module work with one port at 1Gb and the second port at 10gb simultaneosly? It's possible to work each port of the module with different speed (one port working on 1Gb mode and the other working on 10Gb mode)?
View 1 Replies
View Related
Apr 4, 2012
I've been using a Linksys WRT54GSV4 router since November 2005, and have rarely had any problems with it. Now today after the power went out, devices cannot connect to the internet.My PC connected directly to the cable modem results in internet connectivity.My PC connected to the router allows router access through 192.168.1.1.My PC connected to the router can NOT access the internet or otherwise get out to the modem.WiFi devices in the house cannot connect to the internet, but can still access the router through 192.168.1.1.Swapping cables results in the same behavior, so the PC can connect to the modem with either cable, and the computer can connect to the router with either cable.
View 1 Replies
View Related
Aug 6, 2011
We got a lynksys model at our home. it seems that everything is working the pc's connected with cables are working with internet. The wifi sends out and you can get on it. But internet isn't working with wifi also if it says connected etc.
View 1 Replies
View Related
Jul 29, 2012
i have two diffrent-2 network connection and now i want to use both connection for load balancing and speed browsing.
View 2 Replies
View Related
Jul 4, 2011
will the use of mobile wireless internet connection and broadband inet connection simultaneously can be used to download softwares or video files faster than these two used seperately?
View 2 Replies
View Related
Jul 8, 2011
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies
View Related
Nov 29, 2012
I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
No internet access.
View 9 Replies
View Related
Sep 28, 2011
I have had a WRT54G V3 router working successfully for a number of years now with a couple wireless PCs through a cable modem with Comcast as my ISP. All of a sudden yesterday, neither PC could access the internet. No changes had been made to the router.
I contacted Comcast and they of course had me hard-wire one of my PCs into the cable modem. That worked and I was able to access the internet. However, when I tried to put the router back in place (in either a wired or wireless fashion), I could not access the internet.
I've tried following the online Linksys troubleshooting document ion. The lights that should be lit on the router are lit. I can access the router setup web page which shows the settings still intact. I've tried going through the power sequencing to no avail. Comcast says my router is the culprit of my problem, but I don't know why it would all of a sudden stop working. My wireless printer still works so it detects a signal and my PC shows it's connected, but no internet access is possible.
What do I need to do? Are there any other diagnostic tools available? I'm out-of-warranty.
View 4 Replies
View Related
Sep 13, 2012
i am a using a WRT54GH linksys router.. which was working fine for a year.. there was thunderstorm and lightning a few days back.. since then my routers internet port (the first port which says internet in yellow) has stopped working..
View 5 Replies
View Related
Jan 28, 2012
I have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies
View Related
Feb 3, 2013
I'm having a bit of trouble with my e4200, It keeps on "dropping" connection, and by dropping I mean it constantly around 3-5 minutes the internet stops working with all my computers, it's connected by wifi with 2 PC's, and 1 PC is wired with an ethernet cable, and I also have 2 mobile devices connected at it. The internet would start working again within 30s, to 1m, but that it drops soon.Methods I've done to fix it:
-Updated firmware to the latest one
-Set the MTU to 1400
-Reset it, (30 second press)
-Rebooted, (Cooled down, doesn't really run hot just a little warm)
-Restored to factore defaults
View 4 Replies
View Related
Jul 11, 2012
I purchased an e4200 about 6 months ago and it worked great until the other night the Internet stopped working on my laptop (wireless). I tried unplugging both my modem (Motorola Surfboard) and router and plugging them back in, but no luck. I can accesss the Internet when plugged directly into the router (with both my PC and laptop), so it looks like the issue is with the e4200. To make matters worse (and I fear much worse), I can't even access the admin page to the router through either the Cisco Connect software or through the IP address. I've tried resetting it, I've tried the 30/30/30 reset (holding the reset button while doing an unplug and pluging back in), and reinstalling the Cisco Connect software, all to no avail.
I've found threads where others have not been able to access the admin page, but they still had access to the Internet url... I haven't found a similar thread where the router doesn't seem to work at all. A few other bits of information I can think of (let me know if there's other information I can provide):The Cisco logo light flashes slowly after reset which I believe is expected.The lights in back of the router seem to work as intended.Running Windows 7 Diagnostics finds the connection "doesn't have a valid IP configuration" and "The default gateway is not available."
View 9 Replies
View Related
