I know that the C3KX-NM-10GT network module has two (copper) ports that support speeds of 1Gps or 10Gps. Could this module work with one port at 1Gb and the second port at 10gb simultaneosly? It's possible to work each port of the module with different speed (one port working on 1Gb mode and the other working on 10Gb mode)?
View 1 RepliesFor the c3kx-nm-1g network module it looks like it will take the standard sfp's for fiber but I need copper rj45 connections, is there a copper sfp for this?
View 1 Replies View Relatedconfirm the C3KX-NM-10G module is hot-swappable.i have checked the cisco's website and it says " Although network modules are hot-swappable, we recommend installing a network module before powering the switch"
What steps i need to follow to install the module?
A product I could have used a number of times is a expanded version of the C3KX-NM-1G device module. To include 2 or maybe 4 more SFP ports. From the layout behind the faceplate there is plenty of space which additional circuit boards could be placed, (which is used in the 2 port 10GB version). I don't need the 12 port fiber switch that Cisco has, because I need a few RJ45 connection at that location, which I would then have to buy additional Fiber to coper Gbics for a few connections where the switch is at. The reason I need something like this is I have a few locations which I get a main feed from the City fiber, then it gets sent out to a number of local buildings on my fiber. Maybe another option is to take the 12port switch, and have an option for 6 rj45 and 6 sfp connections.
View 8 Replies View RelatedI was trying to get a visio stencil for C3KX-NM-1G module but it doesn't seem to exist. It indeed does not exists or I just can't find it.
View 2 Replies View RelatedI am having trouble updating the epld image on the 10gb Module of Nexus 7k. we have two nexus and two 10gb module. Tried the other one and it worked fine. its jsut the first one that has problems with the epld image. i have tried on both the nexus on two different slots and still the same error.
I get the following error:
Chain connectivity is broken while upgrading the FPGA. (Error Number : 36)
We got a requirement for 2 number of X2-10GB-SR line card WS-X45-SUP6-E in WS-C4506-E.Customer want to connect with Fujitsu primary server . they have 10 gig module so i guess it will support with that.Also a doubt this X2-10GB-SR we can directly connect the firber sc multimode cable write no additional sfp required write .And for my knowledge if i use CVR-X2-SFP. I think to multimode sfp we have to insert write so do we get to 10 gig ports in one slot or how is it .
View 1 Replies View RelatedI am trying to connect tow 3560X using a fiber cable (MM)I have C3KX-NM-10G in both switches (4 ports module)I have GLC-SX-MM in both switches (connected to G1/1)both switches are able to see & recognize the NM as well as the SFP.
Fiber Cable is tested Fiber Patch Cord also tested both ports configured as a trunks but also the switches are not able to see each other (even when I removed the trunks configuration from both of them)CDP neibour is showing nothing no links & no LED blink in any switch both switches are running c3560e-universalk9-mz.122-55.SE3 IOS?
There is no any other configuration in both switches.
In my Cisco 3750 get rebooted and now the SFP module is not working.
It showing the following error message.
05:13:22: %PHY-4-CHECK_SUM_FAILED: SFP EEPROM data check sum failed for SFP inte
rface Gi1/0/26
05:13:22: %GBIC_SECURITY_CRYPT-4-ID_MISMATCH: Identification check failed for GB
IC in port Gi1/0/26
What is the error message indicating and what is the solution for this.
I am going to install new Nexus 7K. Installed SUP and one 32-Port 10Gb module. When I open the box to install this 10Gb module, I saw that there is a carbon paper is tighted with ***** on the top of the module. confirm either it will insert in Switch with carbon paper or have to remove this carbon paper?
View 1 Replies View RelatedI have a 3750-x switch with module C3KX-NM-10G. In slots 1 and 3 I have GLC-T inserted, no problem. When I try to insert GLC-T into slots 2 or 4, I receive the log messages that are listed below. I can swap/mix and match different GLC-T's in slots 1,2,3, and 4, the SFP's are recognized every time in slots 1 and 3, and are never recognized in slots 2 or 4.
Slots 2 and 4 also double as the Ten Gig interfaces, which we are not using right now.Is there some trick to getting the switch to recognize SFPs in slots 2 and 4? [code]
I have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
show interfaces g1/1/3 capabilities
GigabitEthernet1/1/3
Model: WS-C3750X-48P
Type: 10/100/1000BaseTX SFP
Speed: 10,100,1000,10000,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
[code]....
Is the C3KX-PWR-1100WAC= compatible with the WS-C3750X-24P-S?
View 1 Replies View RelatedI have a Catalyst WS-C3750X-24T-S with two power supply C3KX-PWR-440WDC, each of these power supply have two input to deliver 440 W, my question is: Can I use only one Input in each power supply to power up the switch?, I know that I dont going to get the total power of 440W, but the power delivers by the supply with one input circuit is enough to power up the switch condidering that the switch are not PoE and only have 24 ports?.
View 3 Replies View RelatedWe have WS-C3750-24FS switches stacked supporting users on our LAN. I want take advantage of the netflow capabilities of the WS-C3750X using the C3KX-SM-10G card.
Would I be to see netflow data coming from the WS-C3750's if I stacked it with the WS-C3750X?
Also I read that the C3KX-SM-10G card would support a 1G SFP is that correct?
our network is spread over 15 floors and each floor we have 5-6 switches. we are planning to purchase cat3750-x 24 ps poe with C3KX-NM-10G network modules. Each floor has two up links to the core switch with single mode fiber and other being the multimode.Suppose if we are purchasing 75 switches do we have to purchase 75 C3KX-NM-10 G modules.? or can we limit our purchase with 15 C3KX-NM-10G sothat two uplinks from each floor can be made? since network modules are optional cost factor is invovled. Or any issue with stacking ? the SFPs will be LR and LRM MODULES.looking for an answer ? whether the new usb type console cable comes bundled with cat350x or shall we have to order separately?
View 7 Replies View RelatedI need to connect one sw3750E with two 3750X , with Uplinks at 10 GBps. My doubt is the next:
Switch 3750E has two TwinGig Adapter Converting 10 Gigabit Ethernet X2, phisically each twinGig adapter has 2 slots for SFP modules. Can I install sfp+ If I want to use copper for Uplink at 10 Gbps, I just need to install one SFP-H10GB-CU5M transceiver ???? the other SFP slot is disabled automatically?
in the other side 3750X in order to support copper at 10 Gbps a C3KX-NM-10G network module is considered, this will be connected to SW3750E by means of SFP-H10GB-CU5M.
The second 3750X will be connected to second twinGig Adapter of 3750E using another SFP-H10GB-CU5M transceiver.
Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.
View 2 Replies View Relatedknow if it is supported connecting the SUP7L-E 10GE ports to a C3KX-NM-10G, using a SFP-H10GB-CU5M (or shorter).
View 3 Replies View Relatedone side Catalyst 6500 module with X2-10GB-SR= otherside WS-C2960S-48FPD-L.
is both end compatible with each other.
i will be buying 2 x 3750-E and will connect our server with 10G to the x2 port of 3750. is X2-10gb-SR compatible with this? do i need any converter module?
View 1 Replies View Relatedi have question about router 2811, for now, all HWIC in 2811 is full,
Slot 0 : VIC2-2E/M
Slot 1 : VIC2-2E/M
Slot 2 : WIC-1T=
Slot 3 : HWIC-1FE
But we need add more 2 module VIC3-2E/M. can we use Network Module ? example : add one NM-HD-2V + two VIC3-2E/M ?
Can we do that? and whether it is the same as we use the VIC2-2E / M on HWIC slots
Is it possible to mix 1 and 10 Gigabit links on a 1/10Giga Network Module of the Cat3750X? I mean porte GE1/1/1 and GE1/1/2 used with SFP and port TE1/1/2 used with SFP+; that makes TE1/1/1 not available as GE1/1/3 and 1/1/4
View 7 Replies View RelatedI'm looking at provisioning a Catalyst 4500 with a WS-X4712-SFP+E module to allow for future 10Gb connectivity via 10Gb SFP+ interfaces. These cards are backwards compatible with standard 1Gb SFP interfaces but I'm wondering about the other way around; ie. can you populate these blades with 10Gb SFP+ interfaces when they connect to Catalysts with only 1Gb SFP interfaces at the other end?
The data sheets don't really explain this. It seems pointless getting 10Gb SFP+ interfaces for the 4500 when it's only 1Gb at the access layer end, but these access switches will be replaced in the near future (~12 months) and if the 10Gb SFP+ interfaces support connections at 1Gb speeds upfront, it would mean I could retain these interfaces when the access switches upgrade to 10Gb connectivity capabilities down the track. Does the 10Gb SFP+ interfaces are compatible with 1Gb SFP's or only other 10Gb SFP+ interfaces?
Created two 6509s as VSS with just one 10gb connection?I know it is recommended to use both the 10gb connections on the sup-720 from below configuration guide
"
Information about VSL Topology
#
A VSS contains two chassis that communicate using the VSL, which is a special port group. Configure both of the 10-Gigabit Ethernet ports on the supervisor engines as VSL ports.
"
But will the VSS come up if I use just the one?
I have 4900M with X2-10G-LX4I need to have a link from it to 3560X GLC-SX-MM using MM Fiber Patch Cord.any configuration required in 4900M to change the speed of X2-10GB-LX4 to 1GB ?
View 2 Replies View RelatedDoes the X2-10GB-T copper transceiver is supported on the WS-X45-SUP6L supervisor?
View 1 Replies View RelatedI have two 3750 stacks that are currently connected using two1GB fiber connections in an etherchannel. I now added new switches to each stack with 10GB modules in them. We would like to bring up the 10GB connection, but still have one of the 1GB lines as a backup, or even the whole etherchannel. Is there a way for us to make the 10GB the main and the 1GB the standby?
View 3 Replies View Related For a simple 4x sites design for backup consolidation (3x sites connected to one central site), does the design in the attached JPEG make sense and is the configuration achievable using the specified parts?
Brief Explanation:
- Each site is to have servers with 2x 10Gb/s Ethernet (both teamed/bonded/etc) and one NIC on each of the 2x switches in the site (if possible). Each site will also have 2x Cisco Nexus 5596UP Switch (though the P version may be used instead of the UP).
- Two of the sites are within 10KM of the central site
- The last site is about 35KM from the central site
- It is required to have a minimum bandwidth of 10Gb/s between any site and the central site
- I have specified 10Gb/s LW SFP+ and 10Gb/s LW SFP+ (for the 2x 10KM and 1x 35KM sites)
- are there any special licenses needed?
- as asked before, can such a "simple" design work as-is?
- what sort of single-mode fiber would fit the bill (especially for the 40KM link) - 9nm?
We are having troubles getting a 10Gig interface to come up with a carrier... it shows down down.We are using X2-10GB-LR on a 6500 and SM fiber, distance to carrier hand off is about 90 feet.
According to: [URL]
The receiver power on a X2-10GB-LRis
Max
0.5
Min
-14.4
Our carrier is sending at +5db. Currently the interface is down.
My question is; would the interface even come up if it is receiving a powerful signal?
Here is DOM output for our interface.
show interfaces transceiver detail
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
[Code]....
how we can select a network module for 2811 router?gigabit or ethernet Hwic?
View 1 Replies View Relatedcan i use any downlink port of the C4500-X switch as uplink without the need of the network module?i need to connect that switch to C6500E backbone without getting the network module, is that OK or i must get the network module?
View 1 Replies View RelatedI need to know if is possible to do a LACP using 2 x 10GB between 3750X and 2960S (WS-C2960S-48LPD-L) switches.
View 1 Replies View Related