Cisco Switching/Routing :: SFP-H10GB-CU5M Cable To Connect SUP7L-E To C3KX-NM-10G On 3750X
Oct 23, 2012know if it is supported connecting the SUP7L-E 10GE ports to a C3KX-NM-10G, using a SFP-H10GB-CU5M (or shorter).
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: SFP-H10GB-CU5M Versus SFP-H10GB-ACU7M
Jun 28, 2012What is the difference between passive an active Twinax cables? Specifically Cisco SFP-H10GB-CUxM and Cisco SFP-H10GB-ACUxM .
View 3 Replies View RelatedCisco Switching/Routing :: 3750X - Connect C3KX-NM-10G To X2 10G Port On Sup2t In 6500E?
Mar 17, 2013Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 3750x 24 PS POE With C3KX-NM-10G Uplink Modules?
Sep 5, 2012our network is spread over 15 floors and each floor we have 5-6 switches. we are planning to purchase cat3750-x 24 ps poe with C3KX-NM-10G network modules. Each floor has two up links to the core switch with single mode fiber and other being the multimode.Suppose if we are purchasing 75 switches do we have to purchase 75 C3KX-NM-10 G modules.? or can we limit our purchase with 15 C3KX-NM-10G sothat two uplinks from each floor can be made? since network modules are optional cost factor is invovled. Or any issue with stacking ? the SFPs will be LR and LRM MODULES.looking for an answer ? whether the new usb type console cable comes bundled with cat350x or shall we have to order separately?
View 7 Replies View RelatedCisco Switching/Routing :: 10 Gigabit Ethernet Uplinks 3750E To C3KX-NM-10G With 3750X
Jan 5, 2012I need to connect one sw3750E with two 3750X , with Uplinks at 10 GBps. My doubt is the next:
Switch 3750E has two TwinGig Adapter Converting 10 Gigabit Ethernet X2, phisically each twinGig adapter has 2 slots for SFP modules. Can I install sfp+ If I want to use copper for Uplink at 10 Gbps, I just need to install one SFP-H10GB-CU5M transceiver ???? the other SFP slot is disabled automatically?
in the other side 3750X in order to support copper at 10 Gbps a C3KX-NM-10G network module is considered, this will be connected to SW3750E by means of SFP-H10GB-CU5M.
The second 3750X will be connected to second twinGig Adapter of 3750E using another SFP-H10GB-CU5M transceiver.
Cisco Switching/Routing :: SFP-H10GB-CU3M Not Working In 2960S
Feb 15, 2013We have a 2960S using a single SFP-10GBase-SR to our Core switch. We are planning connecting the 2960S to a pair of Nexus 5k switches using Copper SFPs. We are already doing this on another 2960S so I didn't expect any surprises.
When I removed the unused SFP-10GBase-SR from te1/0/2, the interface was removed from the config and a gi1/0/50 was created in its place. Once I inserted the SFP-H10GB-CU3M, I expected that it would create a new te1/0/2 interface, but it didn't. I got the following errors: %GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port Gi1/0/50 has bad crc %PM-4-ERR_DISABLE: gbic-invalid error detected on Gi1/0/50, putting Gi1/0/50 in err-disable state
I didn't personally order the cables, but there is no Cisco label on them, so I'm assuming it is a 3rd party SFP. After looking at other posts related to unsupported SFPs, I ran the following commands: no errdisable detect cause gbic-invalid service unsupported-transceiver
After reconnecting the SFP, it didn't go into err-disable, but I still received the following error: %GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR: GBIC in port Gi1/0/50 has bad crc
My other working 2960S appears to be using 3rd party SFP as well, but I can't see the brand. Is there anything else worth trying or should I just suck it up and order Cisco SFPs?
Cisco Switching/Routing :: 3750x Replacing 2nd Stack Wise Cable?
Nov 20, 2011I have two 3750G switches stacked together however it's not in a full ring configuration:
Stack Ring Speed : 16G
Stack Ring Configuration: Half
Stack Ring Protocol : StackWise
And as shown below it's obvious which cable is not working:
show switch neighbors
Switch # Port 1 Port 2
-------- ------ ------
1 2 None
2 None 1
It's not flapping - it's like the cable isn't there at all. I'm going to try reseating the cable in there and perhaps an all out replacement if necessary. My question - is there any threat of a reboot of the switch stack or of partitioning of the switch stack by trying to get the 2nd cable working?
Cisco Switching/Routing :: Datasheet Of WS-X45-SUP7L-E
Sep 5, 2011Any information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies View RelatedCisco Switching/Routing :: Correct Way To Lic VSS On 4500 SUP7L-E
May 13, 2013What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies View RelatedCisco Switching/Routing :: Sup7L-E - How To Select 1-Gigabit Operation
Aug 23, 2012Documentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 Replies View RelatedCisco Switches :: SFP-H10GB-CU1M SFP+ Copper Cable Module Speed Shows As Unknown
Jul 17, 2012I have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module. Since the port shows as a 10G port, I would expect the speed to show as 10G as well. However, it shows as "Unknown". This doesn't leave me with confidence that it is being recognized properly. The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not. Shouldn't it show 10G as the link speed?
View 12 Replies View RelatedCisco Switching/Routing :: SUP7L-E Support For Shared Backplane Mode
Feb 6, 2012Are there any plans to support a "shared backplane mode" like on SUP6-E that enables the use of four 10G oversubscripted uplink ports in redundant mode? now there is support for up to two active 10G links in redundant mode.
View 2 Replies View RelatedCisco Switching/Routing :: 4500E SUP7L-E Shows Error In Log After Upgrading
May 14, 2012I upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
Cisco Switching/Routing :: Core 4506 / Difference Between Sup7 And Sup7L?
Aug 17, 2012I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedCisco Switching/Routing :: 4507 SSO Mode Sup7L-E 10GbE Interfaces
Dec 9, 2012What is the case with redundant Sup engine 10GbE interfaces. We can only get one in active state, the other interface stays inactive? Can we have all four interfaces active sharing the backplane?
Mod Ports Card Type Model
---+-----+--------------------------------------+------------------+-----------
3 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
4 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot
Cisco Switching/Routing :: 3750-x With C3KX-NM-10G Not Recognizing SFP
Jul 29, 2012I have a 3750-x switch with module C3KX-NM-10G. In slots 1 and 3 I have GLC-T inserted, no problem. When I try to insert GLC-T into slots 2 or 4, I receive the log messages that are listed below. I can swap/mix and match different GLC-T's in slots 1,2,3, and 4, the SFP's are recognized every time in slots 1 and 3, and are never recognized in slots 2 or 4.
Slots 2 and 4 also double as the Ten Gig interfaces, which we are not using right now.Is there some trick to getting the switch to recognize SFPs in slots 2 and 4? [code]
Cisco Switching/Routing :: Install A C3KX-NM-10G Module
Feb 20, 2012confirm the C3KX-NM-10G module is hot-swappable.i have checked the cisco's website and it says " Although network modules are hot-swappable, we recommend installing a network module before powering the switch"
What steps i need to follow to install the module?
Cisco Switching/Routing :: Interface Numbering Plan On CAT4500E With SUP7-E Or SUP7L-E
Feb 1, 2013We are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies View RelatedCisco Switching/Routing :: GLC-T In C3KX-NM-10G - Full Duplex Does Not Work
Jun 4, 2013I have C3750X with C3KX-NM-10G, and have-T SFP in slot 3 ( means it is not in SFP+ slot ).I need to set speed&duplex hard to 100/Full, but if I do the link goes down. I have the same settings on the other side, only IOS version is different.I tried other speeds - 10 and 1000, but no one works with Full. When I change duplex to Auto it works fine.The reason why I am doing this on C3KX-NM-10G is because I need to use NetFlow and cannot use the chassis' copper port. At the moment the ports are connected through a copper patch cord, but in full production there will be a radio link in between that requires 100M/Full to be set hard.I am trying to search for any document that would describe this limitation, but cannot find any. Also port capabilities do not indicate duplex could not be set to full:
show interfaces g1/1/3 capabilities
GigabitEthernet1/1/3
Model: WS-C3750X-48P
Type: 10/100/1000BaseTX SFP
Speed: 10,100,1000,10000,auto
Duplex: half,full,auto
Trunk encap. type: 802.1Q,ISL
[code]....
Cisco Switching/Routing :: C3KX-PWR-1100WAC / WS-C3750X-24P-S - Compatibility
Mar 5, 2012Is the C3KX-PWR-1100WAC= compatible with the WS-C3750X-24P-S?
View 1 Replies View RelatedCisco Switching/Routing :: RJ45 - Getting Expanded C3KX-NM-1G Module?
Dec 29, 2011A product I could have used a number of times is a expanded version of the C3KX-NM-1G device module. To include 2 or maybe 4 more SFP ports. From the layout behind the faceplate there is plenty of space which additional circuit boards could be placed, (which is used in the 2 port 10GB version). I don't need the 12 port fiber switch that Cisco has, because I need a few RJ45 connection at that location, which I would then have to buy additional Fiber to coper Gbics for a few connections where the switch is at. The reason I need something like this is I have a few locations which I get a main feed from the City fiber, then it gets sent out to a number of local buildings on my fiber. Maybe another option is to take the 12port switch, and have an option for 6 rj45 and 6 sfp connections.
View 8 Replies View RelatedCisco Switching/Routing :: Get Visio Stencil For C3KX-NM-1G Module
Dec 19, 2012I was trying to get a visio stencil for C3KX-NM-1G module but it doesn't seem to exist. It indeed does not exists or I just can't find it.
View 2 Replies View RelatedCisco Switching/Routing :: 3560X C3KX-NM-10G (SFP Link Is Not Working)?
May 12, 2012I am trying to connect tow 3560X using a fiber cable (MM)I have C3KX-NM-10G in both switches (4 ports module)I have GLC-SX-MM in both switches (connected to G1/1)both switches are able to see & recognize the NM as well as the SFP.
Fiber Cable is tested Fiber Patch Cord also tested both ports configured as a trunks but also the switches are not able to see each other (even when I removed the trunks configuration from both of them)CDP neibour is showing nothing no links & no LED blink in any switch both switches are running c3560e-universalk9-mz.122-55.SE3 IOS?
There is no any other configuration in both switches.
Cisco Switching/Routing :: C3KX-PWR-440WDC On Catalyst WS-C3750X-24T-S
Oct 2, 2012I have a Catalyst WS-C3750X-24T-S with two power supply C3KX-PWR-440WDC, each of these power supply have two input to deliver 440 W, my question is: Can I use only one Input in each power supply to power up the switch?, I know that I dont going to get the total power of 440W, but the power delivers by the supply with one input circuit is enough to power up the switch condidering that the switch are not PoE and only have 24 ports?.
View 3 Replies View RelatedCisco Switching/Routing :: Upgrade Cat4506 With Sup7L-E Engine To Latest Ip Services Software
May 28, 2012i need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies View RelatedCisco Switching/Routing :: Stack WS-C3750-24FS With WS-C3750X To Use C3KX-SM-10G
Aug 9, 2012We have WS-C3750-24FS switches stacked supporting users on our LAN. I want take advantage of the netflow capabilities of the WS-C3750X using the C3KX-SM-10G card.
Would I be to see netflow data coming from the WS-C3750's if I stacked it with the WS-C3750X?
Also I read that the C3KX-SM-10G card would support a 1G SFP is that correct?
Cisco Switching/Routing :: 3750 C3kx-nm-1g - Network / Copper Module For It
Oct 18, 2012For the c3kx-nm-1g network module it looks like it will take the standard sfp's for fiber but I need copper rj45 connections, is there a copper sfp for this?
View 1 Replies View RelatedCisco Switching/Routing :: Can't Connect To Console On 3750X Stack Members
Oct 23, 2012I have a 3750X stack of 6 switches, I have a terminal server console server plugged into the console ports of all 6 switches. I am having a strange issue where I can connect to the master via the console, get a login prompt then I can log in, but when I try and connect to any of the members then I get a prompt "Press RETURN to get started" When I push return, it just loops back to the same prompt again:
switch-6 con0 is now available
Press RETURN to get started.
switch-6 con0 is now available
Press RETURN to get started.
I can connect to the stack via SSH fine etc. I am running 15.0(1)SE2. The stack is configured for TACACS+ auth via Cisco ACS.
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
*1 Master f0f7.55ba.2700 15 1 Ready
2 Member f0f7.5541.da00 14 1 Ready
3 Member a493.4c1e.4b80 13 1 Ready
4 Member f0f7.5585.cb80 12 1 Ready
5 Member a44c.1120.8e80 11 1 Ready
6 Member a493.4cc0.fa80 10 1 Ready
Cisco Switching/Routing :: C3KX-NM-10GT Network Module Working At 1Gb And 10Gb Simultaneously
Aug 14, 2012I know that the C3KX-NM-10GT network module has two (copper) ports that support speeds of 1Gps or 10Gps. Could this module work with one port at 1Gb and the second port at 10gb simultaneosly? It's possible to work each port of the module with different speed (one port working on 1Gb mode and the other working on 10Gb mode)?
View 1 Replies View RelatedCisco Switching/Routing :: 2801 Cannot Connect With Console Cable
Jun 12, 2013I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedCisco Switching/Routing :: 3750v2 What Kind Of Cable Should Be Used To Connect
Jan 18, 2012According to documentation Cisco RPS 675 should have support for Cisco 3750v2 switch(WS-C3750V2-48PS).What kind of cable should be used to connect them?Cisco RPS has 16 pins and 3750v2 has 22 pins.I could not find that type of cable,
View 2 Replies View RelatedCisco Switching/Routing :: Connect 3550 Cable Modem (dynamic Ip)
Oct 8, 2012I have a Home Virgin media cable connection at home. the only way to get this working with my Cisco gear is by putting the superhub on modem mode.On modem mode, it becomes just a dumb modem assigning and IP via DHCPI can get the switch to get an IP address from the modem with
no switchport
ip address dhcp
then I have created
0.0.0.0 0.0.0.0 fa0/48
to route traffic to the port connected to the mode,The switch gets the assigned Ip address from the modem but it does not route internet traffic.
From the different vlans and subnets on the switch, I can ping the modem.
From the switch I can ping 8.8.8.8
From the machines, i cannot ping 8.8.8.8
On my machines, what should be the gateway? the vlan SVI, the modem's IP address, The fa0/48 ip address? I have tried them all with no success.
Cisco Switching/Routing :: Catalyst 2960 - Can SFP+ Cable Be Used To Connect As Stack?
Apr 25, 2013I have two Cisco 48 port Catalyst 2960-S series SI. Instead of buying the pricy stack modules can I only use the SFP+cable to connect them as stack? which type of SFP+cable should I buy? do I need any license to use those SFP ports?
View 9 Replies View Related