Cisco Switching/Routing :: Interface Numbering Plan On CAT4500E With SUP7-E Or SUP7L-E
Feb 1, 2013
We are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies
ADVERTISEMENT
Aug 17, 2012
I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies
View Related
Oct 18, 2012
i want to activate flexible netflow on my WS-X45-SUP7-E with IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG. I've started with a simple configuration like this:
Configuring a Flow Monitor for IPv4/IPv6 Traffic Using the Flexible NetFlow
“NetFlow IPv4 Original Input” Predefined Record
SUMMARY STEPS
View 1 Replies
View Related
Jan 17, 2010
I was wondering if a interface numbering scheme is available for the 4900M. Configuration includes 1 x 8Port 10G and 1 x 20Port 1G modules. would like to understand How the slots are addressedInterface AddressingTwinGig interface addressing
View 10 Replies
View Related
Jul 22, 2012
We recently had a contractor deploy a 4500 catalyst switch with a WS-x45-SUP7-E. After installation and configurations, HP openview is detecting a "downed" interface on the 4500 chassis that is not in the configuration. I have attached an image with the interface circled. We assumed that it may be a configuration issue with openview, however after running diagnostics with a network analyzer, the same ip address for the down interface is still detected. Is this some sort of internal virtual interface on the SUP7?
View 4 Replies
View Related
Nov 7, 2011
I see there are two different part numbers for Sup7-E. One has /2 at the end. So what's the difference between them?
View 2 Replies
View Related
Jul 30, 2012
SSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
View 2 Replies
View Related
Jul 17, 2012
I have a Catalyst 4500 L3 Switch Software (cat4500e UNIVERSAL-M), Version 03.02.00.XO RELEASE SOFTWARE (fc2). So I just wanted to verify that the switch only does dot1q encapsulation because the switchport trunk encapsulation dot1q command does not work.
View 3 Replies
View Related
Sep 5, 2011
Any information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies
View Related
Jan 30, 2013
How the port numbering would be on Sup 7-E and Sup 7L-E? I mean, on Sup-6E and Sup-6LE, if I used a twin-gig converter, I used ports gi3/3,gi3/4,gi3/5 and Gi3/6 [If the sup is in 3rd Slot]. I know there are now 4 ports on the Sup 7 which can either be used as Gig ports or TenGig ports. So, how will the port numbering change ?
View 1 Replies
View Related
May 13, 2013
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies
View Related
Apr 2, 2013
blank configuration for WS-C4500X-16SFP+ (Catalyst 4500-X 16 TenGig Fixed ports switch).
I would like to know how the port numbering is done (i.e. TenGig1/0/X or TenGig1/X or just Eth1/0/X ? )
View 1 Replies
View Related
Aug 15, 2012
Concerning the WS-X4640-CSFP-E module, I was surprised to realize when I got it that the ports are numbered 1-80 rather than 1-40. Then I saw it is actually an 80 port blade when you use half-SFP's. But we have full SFP's, so how does it do the numbering? If I use all full-SFP modules, do the even-numbered ports just go unconfigured?
View 1 Replies
View Related
Sep 30, 2012
I was wondering if an interface numbering scheme is available for the 6509-E switch equipped with SUP-2T and includes 16Port X 10GE DFC4, 48 x 1GE SFP and RJ 45 line cards. Would like to understand:
How the slots are addressed
Interface Addressing
On board SUP-2T 10G and 1G port addressing
View 2 Replies
View Related
Mar 25, 2012
I was contacted by a customer today who is trying to configure QoS on a 4500E with Sup7-E. They are running:
cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin
And the 4500 is licensed for enterprise Services. I don't have access to the switch and am looking for configuration documentation and I am not finding the necessary configuration guides.
View 3 Replies
View Related
Apr 22, 2013
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
View 2 Replies
View Related
Jun 8, 2013
how ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
View 2 Replies
View Related
Aug 23, 2012
Documentation discusses "1-Gigabit Operation", where all 4 1-Gig SFP's on Sup7L-E are enabled. But it does not say __how__ to select either 10-G or 1-G operational modes.
View 3 Replies
View Related
Apr 10, 2012
Assume I had Catalyst 3560X/3750X with 24 ports. The partnumber is WS-C3560X-24P-LI would like to how is the numbering defined if the switches have a C3KX-NM-10G installed with 4 SFP-GE-L.
View 1 Replies
View Related
Feb 6, 2012
Are there any plans to support a "shared backplane mode" like on SUP6-E that enables the use of four 10G oversubscripted uplink ports in redundant mode? now there is support for up to two active 10G links in redundant mode.
View 2 Replies
View Related
May 14, 2012
I upgraded IOS-XE on 4500E (SUP7L-E) to cat4500e-universalk9.SPA.03.03.00.SG.151-1. I encounter the log when i try to issue write mem commad
% VRF table-id 0 not activeCompressed configuration from 8947 bytes to 2140 bytes[OK].
View 3 Replies
View Related
Dec 9, 2012
What is the case with redundant Sup engine 10GbE interfaces. We can only get one in active state, the other interface stays inactive? Can we have all four interfaces active sharing the backplane?
Mod Ports Card Type Model
---+-----+--------------------------------------+------------------+-----------
3 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
4 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot
View 1 Replies
View Related
Feb 16, 2012
When configuring QoS on 3750s/3560s, we're mapping packets to particular interface output queues with commands such as: [code] The command to see what's actually being enqueued, dropped, etc. is: [code]
Note that these queues are numbered 0 - 3, and not 1 - 4. We've been assuming that the first queue number in the "mls qos" (i.e., 1) command maps to the first queue (i.e., 0) in the "show mls qos" command.
View 1 Replies
View Related
Mar 21, 2011
I´m looking for the VISIO icon for WS-X45-SUP7-E and 4507R+E.
View 13 Replies
View Related
Jul 18, 2012
I have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?
View 4 Replies
View Related
Dec 7, 2011
How do I enable ports 3 and 4 on this supervisor module? I can only get ports 1 and 2 to work by default. I have a standby Supervisor in SSO mode. I'm running IOS 15.0.2SG
View 2 Replies
View Related
Dec 17, 2011
I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....
View 2 Replies
View Related
Oct 23, 2012
know if it is supported connecting the SUP7L-E 10GE ports to a C3KX-NM-10G, using a SFP-H10GB-CU5M (or shorter).
View 3 Replies
View Related
May 28, 2012
i need to upgrade my cat4506 with sup7L-E engine to latest ipservices software. link of suitable software and upgrade methode?
View 2 Replies
View Related
Apr 26, 2013
I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies
View Related
May 21, 2013
In testlab we use pim-sm with bootstrap router on sup7 with IOS-XE 03.04.00.SG. Any possibility to prevent non authorized rp from connecting to the candidate bootstrap routers? We found several security recommendations concerning limiting registering of sources at the rp, rate-limits etc, but no possibility to control rp connecting to the bsr.
View 4 Replies
View Related
Oct 15, 2012
I'm trying to configure LLDP-MED between a Cat45010+E Sup7 (IOS 15.1) and Polycom CX600 Lync phones. I have created and applied the correct network policy for the interfaces.
From these sites, I need to send all the correct TLVs or the phones won't respond: {URL}.
When a scour the config of the switch, I can't find any related configuration commands relating to the specific LLDP-MED TLV components which are enabled/disabled. Where are they hiding? I would like to confirm which TLVs are being sent by my switch and if they are matched to the phone. I can always use the DHCP method, put this is not preferred.
View 3 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
