Cisco Switching/Routing :: 4500 Internal Virtual Interface On SUP7
Jul 22, 2012
We recently had a contractor deploy a 4500 catalyst switch with a WS-x45-SUP7-E. After installation and configurations, HP openview is detecting a "downed" interface on the 4500 chassis that is not in the configuration. I have attached an image with the interface circled. We assumed that it may be a configuration issue with openview, however after running diagnostics with a network analyzer, the same ip address for the down interface is still detected. Is this some sort of internal virtual interface on the SUP7?
View 4 Replies
ADVERTISEMENT
Apr 22, 2013
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
View 2 Replies
View Related
Apr 26, 2013
I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies
View Related
Nov 7, 2011
I see there are two different part numbers for Sup7-E. One has /2 at the end. So what's the difference between them?
View 2 Replies
View Related
Feb 1, 2013
We are planning for the first installation of 4500 switches containing these supervisor modules. I'm trying to determine the interface numbering convention for ports on the supervisors. Our existing 4500E all have SUP6 modules with twin-gig converters - so I am familiar with the numbering conventions used on those supervisors. How does this change with the software based selection command "hw-module uplink select" used in SUP7?
View 2 Replies
View Related
Dec 3, 2011
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
View 9 Replies
View Related
Mar 25, 2012
I was contacted by a customer today who is trying to configure QoS on a 4500E with Sup7-E. They are running:
cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin
And the 4500 is licensed for enterprise Services. I don't have access to the switch and am looking for configuration documentation and I am not finding the necessary configuration guides.
View 3 Replies
View Related
Mar 21, 2011
I´m looking for the VISIO icon for WS-X45-SUP7-E and 4507R+E.
View 13 Replies
View Related
Dec 7, 2011
How do I enable ports 3 and 4 on this supervisor module? I can only get ports 1 and 2 to work by default. I have a standby Supervisor in SSO mode. I'm running IOS 15.0.2SG
View 2 Replies
View Related
Aug 17, 2012
I will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies
View Related
Dec 17, 2011
I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....
View 2 Replies
View Related
May 21, 2013
In testlab we use pim-sm with bootstrap router on sup7 with IOS-XE 03.04.00.SG. Any possibility to prevent non authorized rp from connecting to the candidate bootstrap routers? We found several security recommendations concerning limiting registering of sources at the rp, rate-limits etc, but no possibility to control rp connecting to the bsr.
View 4 Replies
View Related
Oct 15, 2012
I'm trying to configure LLDP-MED between a Cat45010+E Sup7 (IOS 15.1) and Polycom CX600 Lync phones. I have created and applied the correct network policy for the interfaces.
From these sites, I need to send all the correct TLVs or the phones won't respond: {URL}.
When a scour the config of the switch, I can't find any related configuration commands relating to the specific LLDP-MED TLV components which are enabled/disabled. Where are they hiding? I would like to confirm which TLVs are being sent by my switch and if they are matched to the phone. I can always use the DHCP method, put this is not preferred.
View 3 Replies
View Related
Apr 5, 2011
I have five 877 routers connected to ADSL circuits provided by Vodafone. Each has a VPN tunnel back to a PIX.
Occasionally one of the sites will lose it's connection to the PIX.
When we check the log, we find entries like these:-
Apr 5 01:31:54.085 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to downApr 5 01:33:19.344 UTC: %CRYPTO-
[Code].....
As you can see, the physical interface (ATM0) is not being reported as changing state to down, neither is the Dialer interface.
When the router is in this state we have to SSL to the public IP address of it and manually restart the ISAKMP SA.
When the router sees the ATM interface go down and subsequently come back up, the VPN connection to the PIX also recovers.
So - in a long winded way I think I'm asking....why does the Virtual interface go down and is there anything I can do to stop it happening?
View 3 Replies
View Related
Jun 15, 2012
We have an ANM Virtual Appliance, version 5.2, were we login and can go no further. This was working for fine for approximately two and half weeks. We created a backup and re-loaded the system via CLI with the same result. We logged in again via SSH and we have noted the following:
cscoanmsa/admin# sh disk
temp. space 4% used (141244 of 4951688)
disk: 7% used (353916 of 5935604)
Internal filesystems:
warning - /var is 100% used (89219000 of 89258112)
cscoanmsa/admin# sh application status ANM
[code]....
Is there any way to access and clean out the /var directory from the CLI. is this achieved simply via the "delete" command with the full path ?
View 5 Replies
View Related
Jun 3, 2012
I have an ASA5510 running version 8.2(5) I am having an issue with routing/natting from an internal network to the outside interface IP on port 443 which has a nat back in to another internal address. i works externally in from a public address. i also see log messages to do with IP Spoofing
View 1 Replies
View Related
Sep 10, 2012
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies
View Related
Apr 9, 2010
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies
View Related
Mar 4, 2013
Today, we have a server running SNA that connects to router via the following. Vitrual Server --> Nexus 1000v ---->Nexus 7010 ---->2800 series router.We are trying to move server to new environment where it is Virtual Server ----> Nexus 1000v ----- Fabric Interconnect-----Nexus 55xx-----Nexus 7010-----2800 router.
View 2 Replies
View Related
Feb 14, 2012
I've created the VLAN on the Database but it tells me that there are no VLANs configured when i issue the command. Both VLAN 110 and 111 status are down, down.. Below is my config:
Building configuration...
Current configuration : 15817 bytes!upgrade fpd autoversion 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice counters max age 10!hostname Router!!no aaa new-modelip subnet-zero!!!ipv6 mfib hardware-switching replication-mode ingressvtp domain Marinersvtp mode transparentmls ip multicast flow-stat-timer 9no mls flow ipno mls flow ipv6no mls acl tcam share-globalmls cef error action freezeno scripting tcl initno scripting tcl encdir!!! !!!!!!!redundancymode ssomain-cpu auto-sync running-configspanning-tree mode pvstno spanning-tree optimize bpdu transmissiondiagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!vlan internal allocation policy ascendingvlan access-log ratelimit 2000!vlan 110name Data!vlan 111name Voice!vlan 112name Video!------------Output
[code]....
View 4 Replies
View Related
Dec 22, 2010
I have a problem in my Cisco 1841 in Virtual-Access Interface all interfaces is UP Except Virtual Access is Down . [code]
when i want recover the virtual access to up ,should i do shut & no shut to the ATM interface.What is the cause of the problem, and how I can solve this issue?
View 2 Replies
View Related
Mar 13, 2013
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).
Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 1 Replies
View Related
Mar 6, 2013
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies
View Related
Feb 28, 2012
Does the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies
View Related
Apr 3, 2013
question on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
View 1 Replies
View Related
Nov 16, 2009
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
View 2 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Feb 11, 2012
We have a 3745 LNS router, currently there are less number of users connected.when a user dials request authenticated and one virtual-access interface is formed in LNS router.Now the user is disconnected the vpn and connected to VPN again in this case, whether the user is connected to the same virtual-access interface which was assigned before disconnecting or different virtual-access interface is created.
View 0 Replies
View Related
May 1, 2012
I have got new cisco ASA 5580 running 7.2(4) on it when i am trying to configured Virtual interface on vlan 400 in Gi0/0.400 to LBASE.now the problem is from my MZ zone 10.242.107.17 to Lbase virtual interface 10.242.103.1 iam not able to ping.
View 2 Replies
View Related
May 13, 2013
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies
View Related
Dec 14, 2011
Why Cisco 4500 R switch PBR tracking Command not working , I found just route-map next-hop ?
View 3 Replies
View Related
Sep 7, 2012
My 4500 core always in 60 % cpu utility , and when i run #sh proc cpu sorted i find that
55 29725041543795572214 0 39.43% 41.40% 41.39% 0 Cat4k Mgmt LoPri
Which mean that this process is the top one , and when i run #sh platform health i found that Stub-JobEventSchedul
10.00 15.98 10 64 100 500 20 17 12 29269:55 K2 CpuMan Review
30.00 35.60 30 48 100 500 49 46 32 52390:52
Those two process are the top and they already exceed their maximum rang and when i run #sh platform cpu packet statistics i can find that Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Esmp 5053121950 475 462 340 326
L2/L3Control 244395185 17 8 5 11
Host Learning 67315739 0 0 0 0
L3 Fwd Low 346689615 73 23 14 13
L2 Fwd Low 5336180603 1180 1129 831 804
L3 Rx Low 2287913 0 0 0 0
RPF Failure 7510829 1 0 0 0
View 2 Replies
View Related
May 23, 2012
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies
View Related
