I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).
Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
in one of the sites, the client has an exisiting 4402 controller which he moved to the DMZ in order to set it as an anchor & he purchased two new 5508 controllers to control the corporate APs. I configured all the parameters needed for the guest anchoring & then I tested the connection but there was an issue. (all the controllers are running the same firmware version)after testing the setup, the guest users could get an IP from the internal DHCP of the anchor controller (in DMZ), but then they cannot reach the internet or anything outside the anchor controller.Cisco confirmed that the 4400 is fully compatible with the 5500 to work in an anchor-foreign secnario as long as they are running the same firmware version. yet, when I temporarily used one of the 5500 controller in the DMZ as an anchor & I applied the exact same configurations on it as the 4400, it worked perfectly without any issues.
note: on the anchor controller (4400), the management & AP-manager interfaces reside on the same subnet & the wireless guest SSID is also mapped to the management interface. (may be this setup is causing the issue) but on the 5500 it is working just fine?
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
I am looking at deploying a Cisco Virtual Wireless LAN Controller (vWLC 7.3).Do I need Prime Infrastructure to manage the environment, or can I manage my AP's (1200 series) using the vWLC alone?
View 6 Replies View RelatedI read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.The command "config mobility group member hash" is totally missing. How to establish a mobility group between a 4400 controller and a virtual then ?
View 2 Replies View RelatedI read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.
But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.
The command "config mobility group member hash" is totally missing.
how to establish a mobility group between a 4400 controller and a virtual then?
We are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.
Region : Hongkong
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
When using the USB printer port share function, I found that some PCs, which had never physically connect to a USB printer before, will not have the virtual USB printer port in the port selection. In this way, TP-Link's USB printer controller will not be able to setup the connection. The PC will not be able to use the shared printer from my WDR3600.how can I create a virtual USB printer port in the remote PCs (without need to physically connect a printer to them) or other method to use the shared printer?
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies View RelatedDoes the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedToday, we have a server running SNA that connects to router via the following. Vitrual Server --> Nexus 1000v ---->Nexus 7010 ---->2800 series router.We are trying to move server to new environment where it is Virtual Server ----> Nexus 1000v ----- Fabric Interconnect-----Nexus 55xx-----Nexus 7010-----2800 router.
View 2 Replies View RelatedI've created the VLAN on the Database but it tells me that there are no VLANs configured when i issue the command. Both VLAN 110 and 111 status are down, down.. Below is my config:
Building configuration...
Current configuration : 15817 bytes!upgrade fpd autoversion 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice counters max age 10!hostname Router!!no aaa new-modelip subnet-zero!!!ipv6 mfib hardware-switching replication-mode ingressvtp domain Marinersvtp mode transparentmls ip multicast flow-stat-timer 9no mls flow ipno mls flow ipv6no mls acl tcam share-globalmls cef error action freezeno scripting tcl initno scripting tcl encdir!!! !!!!!!!redundancymode ssomain-cpu auto-sync running-configspanning-tree mode pvstno spanning-tree optimize bpdu transmissiondiagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!vlan internal allocation policy ascendingvlan access-log ratelimit 2000!vlan 110name Data!vlan 111name Voice!vlan 112name Video!------------Output
[code]....
We recently had a contractor deploy a 4500 catalyst switch with a WS-x45-SUP7-E. After installation and configurations, HP openview is detecting a "downed" interface on the 4500 chassis that is not in the configuration. I have attached an image with the interface circled. We assumed that it may be a configuration issue with openview, however after running diagnostics with a network analyzer, the same ip address for the down interface is still detected. Is this some sort of internal virtual interface on the SUP7?
View 4 Replies View RelatedDoes the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies View RelatedI am running the demo of the virtual WLC and have one 1142N AP connected to it. I have two WLAN's created and they are configured to broadcast their SSID's. However, when I look on my laptop or Android, I cannot see either of them. I checked the AP to see if it has the WLAN's on it and it does. I did this by going to Wireless -> Access Points -> Radios -> 802.11a/n AP Interfaces -> Details. Under Station Configuration Parameters -> Number of WLAN's, there are 2, which is correct. I had this demo running on VMware workstation and had some bridging issues with it and thought that was the issue. I now have it running on ESX5.1 and am still having this issue. I am at a loss as to what is causing this problem.
View 2 Replies View RelatedBelow are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies View RelatedDo the cisco 4503 switches support virtual clustering feature ? I have a requirement where switch ports on two different 4503 switches need to combined in the same Link aggregation group . This is needed because the firewall notes say that the aggregated interfaces need to be conected to a single switch and combined in the same LAG . So according to the diagram below , the interfaces marked RED need to be in the same LAG in the switches , same for the interfaces marked BLUE . I have done the same setup using Juniper switches where it uses VIRTUAL CLUSTERING to group the different switch ports in the same LAG.
View 2 Replies View RelatedIt is possible to add interface from different line cards reference ( for example N7K-148GT-11L and N7K-F132XP-15 ) to a vPC ? I ask you because I try it and I have the following error :
command failed: port not compatible [Capabilities FabricPath]
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies View RelatedI'm looking at deploying a single WLC 5580 into a data centre and I'm trying to decide if to use flexconnect or to tunnel traffic back to the controller. There will be 2 offices each with 40 access points. The wireless will need to support roaming voice traffic. Will I have any issues with flexconnect and 30 access points? I'm aware that you can only have 25 aps per flexconnect group but I dont know if this has any limitations such as dirty roaming? Also is tunneling traffic back to the WLC ok for voice and video traffic as the traffic will have to travel back from the data centreto the local offices ?
View 5 Replies View RelatedIm using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies View RelatedI have a Cisco Wireless LAN Controller WCL2112 model. It's currently plugged into an HP Procurve switch on a trunk port. That HP switch is plugged into my Cisco stack on a trunk port. I can reach the WCL just fine through the LAN. But when I plug the WCL directly into the Cisco stack on a trunk port, I can't reach the WCL at all, unless I connect to it over wireless. The interface shows it's conneccted and up/up. But no communications are sent across the line. I did a wireshark and can see only ARP request from the WCL. The trunk port on the stack is set to:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport mode trunk
The WCL has 3 VLAN's on it and the SSID of VLAN 1 is our office wireless. If that matters. .The Cisco Stack is 4 switches. cisco WS-C3750X-48P
we need to be required to import MAC filter databse from Cisco Wireless LAN Controller (4400) to Cisco ACS Server (v4.2).
View 2 Replies View RelatedI'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
Is it necessary to understand web development to deploy a web server
View 5 Replies View RelatedI tried to deploy configuration templates with Cisco LMS Template Center, due to the 10 Cool LMS Tricks to better manage your network i am able to do it now.Just i don't know why, after deploying these templates the configuration is not save to the startup-config.another problem i have with the snmp-server location configuration. It seems my template does not support spaces in the textbox. Any way to put spaces in the snmp location?
<parameter name="snmp-location">
<description>SNMP Server Location</description>
We are deploying devices with IOS XR and wondered if deploying them with TACACS authenticating to the Cisco ACS 5.x platform.
View 1 Replies View RelatedHaving an issue with my WLC 5500 and client connectivity. This just started today. Clients will connect for a short period of time and then drop off. WLC appears fine with the exception of a bunch of trap errors. I've rebooted the WLC but this did not clear the issue.
View 3 Replies View RelatedI have two workstations running 7 Pro, each has a quad port intel card (PCIe) which I have created teams for on both sides using link aggregation. On my switch, a Cisco SG500X-24, I set up two LAG's with 4-ports each and have both servers connected as necessary. I turned on Jumbo frames and disabled energy saving. The teams were set up without LACP turned on, however I tried it with LACP and I also ran into the same problem. Both workstations have a 26TB arrays running in RAID 6 (so plenty of read/write speed), however, with this setup, I can only get about 100MB/s (single port speed) and multiple data streams cause the speed to divide. Only single ports blink on the cards as well.
Questions 1 is probably a no-brainer, but it's my first time setting this up, but once this is working properly, would it allow a single file to transfer at ~400MB/s or would I need to start multiple datastreams to take advantage of link aggregation.
Question 2 is what do I need to change to make the link aggregation work?
I do have a little linksys router plugged into a non aggregated port to do DHCP but that wouldn't mess anything up, would it? Considering I can unplug it once everything is talking, all the transfer should take place at the switch level, correct?
Is it possible to upgrade the software images on ACE 20 modules and/or ACE 4710 Appliances?
View 0 Replies View RelatedI have a Nexus 7000 Core Switch , and i need to allow the domain controller ip 10.x.x.x for DHCP relay on switch.
View 2 Replies View RelatedBased on what i am reading on the Catalyst 3850 datasheet, the controller functionality comes by default if i have a IP Base of IP Services license on the switch. Is this correct or do i need additional license to enable the controller functionality?What capabilities does below license provide ?
LIC-CT3850-UPG (Primary upgrade license SKU for Cisco 3850 wireless controller)