Cisco Wireless :: VWLC And Aironet 1252 - All Client Devices Such As IPhone / Laptop Can't Find SSID

Sep 6, 2012

I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.

1. WPA2 Auth 802.1X
2. Web-Auth
 
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.

View 3 Replies


ADVERTISEMENT

Cisco Wireless :: VWLC - 1142N AP Not Broadcasting SSID?

Apr 7, 2013

I am running the demo of the virtual WLC and have one 1142N AP connected to it.  I have two WLAN's created and they are configured to broadcast their SSID's.  However, when I look on my laptop or Android, I cannot see either of them.  I checked the AP to see if it has the WLAN's on it and it does.  I did this by going to Wireless -> Access Points -> Radios -> 802.11a/n AP Interfaces -> Details.  Under Station Configuration Parameters -> Number of WLAN's, there are 2, which is correct.  I had this demo running on VMware workstation and had some bridging issues with it and thought that was the issue.  I now have it running on ESX5.1 and am still having this issue.  I am at a loss as to what is causing this problem.

View 2 Replies View Related

Aironet 1121 - Client Isolation On 1 SSID In Cisco Access Point

Feb 2, 2011

i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.

Quote:

Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.

[Code].....

View 3 Replies View Related

Cisco Wireless :: Aironet 1252 Bridge And 802.11n?

Dec 5, 2012

I have two Cisco Aironet 1252  that I want to configure as a point-2-point bridge. Now I want to know if this configuration supports the 802.11n protocol.

View 2 Replies View Related

Cisco Wireless :: Aironet 1252 Boot Error

Jun 11, 2012

an Aironet 1252 which is failing on boot. When power on the access-point shows the error below.
 
WARNING: A memory error occurred during the system start-up self-test.  The device must be serviced if the error persists.
 
The following commands can, optionally, be used to initialize the flash file system and the TFTP file transfer system:
 
But when this happen, I can start the IOS manually doing flash_init and boot in ROMMON. After do this commands, the access-point starts and works normally.
 
How can I check and correct the memory and solve this issue?

View 3 Replies View Related

Cisco Wireless :: Antenna Alignment On Aironet 1252

Oct 27, 2012

I am using two Cisco Aironet 1252 (cisco AIR-AP1252AG-A-K9) to setup a point to point link (one is configured as root bridge and is as a non-root bridge). Both Aironets are running software version Version 12.4(25d)JA.
 
Is there a way that I can that I can perform an antenna alignment test on the Aironet that is configured as a non-root bridge?executing the following command dot11 dot11radio 0 ? does not show the antenna-alignemnet option.

View 11 Replies View Related

Cisco Wireless :: Aironet 1252 / Actual Wireless Link Speed Low

Nov 8, 2012

I have 2 cisco Aironet 1252 setup as a point to point link using an external antenna (one radio is setup as the root bridge the other is setup as the non-root bridge). Now I see that the connection between the radios is established at a speed of 54 Mbps. However when I perform a speedtest on the link I see that the my actual download speed does not exceed the 2,5 Mbps. what can cause my actual speed to be far lower than the 54 Mbps? And what can I do to improve it?

View 16 Replies View Related

Cisco Aironet 1252 Configuration?

Mar 7, 2013

Okay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.

View 14 Replies View Related

How To Configure Cisco Aironet 1252

Mar 7, 2013

I'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .

View 9 Replies View Related

Cisco :: Aironet 1252 AES Encryption?

Dec 5, 2012

I have two cisco airenet 1252 autonamous access point that are configured as  point to point bridge. Now I want to confiure AES encryption or WPA2 using a pre-shared key however I do not see the option to do this . The only option I see under ciphers are:
 
wep 128
wep 40
TKIP

[Code].....
 
Is it possible to use either AES or WPA2 using a pre-shared key  on the 1252 autonamous access point? preferably using the web interface.

View 3 Replies View Related

Cisco :: SNMP OID For Monitoring CPU On Aironet 1252

Jan 27, 2013

I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.

View 1 Replies View Related

Cisco Wireless :: 5508 - SSID For IPad / IPhone

Jul 27, 2012

on a 5508 WLC can we create new SSID for I PAD / IPHONE Users without having ISE, only I phone / I PAD are allowed to be authenticated rest all should be denied.  IS this possible?

View 8 Replies View Related

Cisco Wireless :: Aironet 1100 Weak Signal With Ipad2 Iphone And Blackberry

Apr 11, 2012

in my company we have 40 cisco aironet 1100 without controller, the signal is good with laptops but is too weak with the iphone's ipads and blackberry.

View 12 Replies View Related

Cisco Wireless :: How To Connect Laptop To LAP 1252 With WLC 7.0

Feb 17, 2013

How can i connect my laptop (11n supported) to LAP 1252 with WLC 7.0.116.0?Status: 11a enabled on wlcDCA channel list in 11a on wlc is showing only 149 153 157 161 channels.

View 6 Replies View Related

Cisco Wireless :: Multiple SSID In Aironet 1140?

Nov 18, 2012

I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.

View 2 Replies View Related

Cisco Wireless :: Cannot Connect To Second SSID On Aironet 1231

Apr 22, 2013

I have configure my AP with to SSID (11 & 12), but I cannot connect to 12. It authenticates, and while trying to acquire IP address from 12, it fails and connects me to 11 (if I have already saved the SSID connection).
 
The following is my AP status:Product/Model Number:AIR-AP1231G-A-K9 System Software Filename:c1200-k9w7-tar.123-8.JEE System Software Version:12.3(8)JEE Bootloader Version:12.3(2)JA4  
 
The SSID 12 already have 4 clients connected, And I am tring to connect a 5th one (smart phone), but cannot connect to 12, instead coneected to 11. Also tried with a laptop, but cant get the IP address, and give Limited Connectivity error.

View 3 Replies View Related

Cisco Wireless :: Aironet 1142 Not Broadcasting SSID?

Sep 28, 2012

I configured the device manually, not even using Express Setup or Express Security setup so... it is possible I missed something.Anyway, here's the problem. Although the SSID is configured as "AP1", this SSID does not appear among available networks on the client laptop.
 
The connection, configured in Group Policy for the client, should actually happen automatically, based on the SSID, but since the SSID is not being broadcast, that connection is failing as well.
 
The Aironet does appear among the available networks as "Other Network" and if I click on "connect" I am prompted to enter the SSID -> AP1
 
Although, unexplicably, an error message displays (Windows cannot connect to the network, or something to that effect), the laptop *does* connect once I close that window. Network access is complete and functional - I can ping other hosts, etc..
 
I'd post screenshots but not knowing what setting is missing or incorrect, I'd have to print dozens. So here's the sh run output of the AP obtained via telnet (just below). This is a test network so all information is "real" (nothing changed for privacy):
 
Note: I even changed the hostname to "AP1" (it's still LAB1 below) but that did not resolve the problem (did not think it would).
 
LAB1#sh runBuilding configuration...
Current configuration : 2321 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname LAB1!logging rate-limit console 9enable secret 5 $1$9EWD$kxrbg8KxikRFypOieKiZh/!aaa new-model!!

[Code]....

View 5 Replies View Related

Cisco Wireless :: Change SSID Name On Aironet 1200 Currently Used By Network

Jan 25, 2012

I'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.

View 3 Replies View Related

Cisco Wireless :: Multiple Aironet 1131AG Access Points And Same SSID?

Dec 22, 2009

We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560)  who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11).  They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.

How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?

View 2 Replies View Related

Cisco Wireless :: Configure Multiple SSID On Aironet 3600i AP Via 2504 Controller

Apr 3, 2012

Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?

View 1 Replies View Related

D-Link DIR-655 :: Iphone (1st Generation) Can't Connect And Don't See SSID

Jul 9, 2011

I had a DI-524 for years and I had no problem. My girlfriend wanted more range /speed for her netbook, and bought a DIR-655.

Had no problem with the netbook (acer One) and the Wii. But the Iphone 1st gen (cracked, but working good up to now) won't see any Wifi.

What to say. I have to read the F*  manual, I know. But Geez. "The high end" said the guy at the store.

I should have search the web a bit more before buying because this subject (iphone connect problem) is a popular topic. [URL] won't change a thing. The Iphone don't see the wifi network.

Hardware Version: B1     Firmware Version: 2.00NA

View 5 Replies View Related

Cisco Wireless :: 5508 Best SSID Practices For Really Old Devices On WEP

Jul 26, 2012

setup a WEP SSID on my 5508 controllers.  THat being said, I have multiple sites with extremely old scan guns that only do 104bit wep.  I plan on locally switching this SSID and using static WEP 104bit key with MAC authentication, and then ACLing to limit my inherent security issues/exposure once someone compromises my WEP key.  [code]

View 4 Replies View Related

Cisco Wireless :: Some Devices Are Failing To Connect To Aironet 1262 AP

Jun 10, 2013

Some devices are failing to connect to my Cisco Aironet 1262 AP. So far I have noted the ipad 2, a windows 8 phone and a bang and olufson speaker. Is there something I need to tweak in my config. Other devices connect fine, that is my laptop, desktop and android phone.

View 2 Replies View Related

Cisco Wireless :: 4402 Wlc / Apple Devices Several Retries To Connect SSID?

Jun 11, 2012

In the company we have two SSIDs for corporate and guest networks respectively when I try to connect to any of the SSIDs it doesn't happen until 5 retries. The only log I get that seems to be related to it is the following:
 
*Jun 11 11:48:09.062: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:23:32:73:d7:15 due to switch of WLANs from 1(femsawl) to 2(visitas)
 
Here it shows a switch between SSIDs but if you just turned on an apple device and try to associate for the first time to any of the SSIDs the scenario is the same, several tries to connect.I am running a 4402 wlc with 6.0.202.0 software version.

View 4 Replies View Related

D-Link DIR-655 :: No Connectivity Between Wired And Wireless Devices (on Main SSID)

Feb 24, 2011

Ive had this 655 for about a year now and it has been rock solid. But, there has been one slight issue.

And and all wireless devices can see each other and all wired devices can see each other....but the wired cant see the wireless and vis versa.

The wireless devices (W7 and Vista laptops) can see the wired devices when they are plugged in. But my phone and Galaxy Tab can only see whatever wireless devices there are (cant be plugged in). Even my wired Samsung TV cant see the shares on the Tab or wireless laptops (and vis versa). So, its certainly not a firewall or OS config issue.

Now, I made sure they are all connecting via the main SSID and not the "isolated" Guest SSID....but its acting like the main SSID is isolated from the wired LAN somehow.

Firmware 1.34. IPs for the wired and wireless devices are all in the 1.2 - 1.50 range.

View 14 Replies View Related

Cisco :: Aironet 1240AG Is Not Broadcasting SSID For MAC

Jan 31, 2012

I have a "standart" settings of Cisco Aironet 1240AG with ENABLED broadcasting SSID, encryption is WPA2 (AES). I can see the wifi network (ssid) with windows system but with MAC OS 10.5 and MAC OS 10.7 also with iPhone the wifi is acting like hidden. But If I manually enter the wifi ssid and set the proper encryption the connection work normally. Also I have a separete windows partition on one MACbook and this windows 7 have no problem to see the SSID of my network. But If i Boot to the MAC OS the WIFI is "hidden" until the manually connection. (same problem on iphone, manuall connect with manually entered SSID is working well).

View 2 Replies View Related

Cisco :: SSID To Radius Without WLC (Aironet 1240)

Mar 4, 2013

I am working on setting up a new WLAN infrastructure. I have set up different SSIDs connected to different VLANs, in the AP. I also want to use Windows NPS for authenticating users on the different SSIDs, with different authentication methods based on which SSID the user/device is connecting to. To do that, NPS needs to get the SSID, but the Aironet 1240 only sends its MAC address in the Called-Station-Id. I have read a bit about this, and found out that if I have a WLC, it will add the SSID to to the Called-Station-Id. But since we do not have a WLC, I am trying to get this to work anyway. Is it possible to modify the Called-Station-Id to include the SSID on an Aironet 1240? If not, is it possible to send the SSID as a separate attribute that can be read by the NPS?

View 10 Replies View Related

Cisco Wireless :: Aironet 3602i Not Working With SAP (NetWeaver) Client

Jul 16, 2012

Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
 
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
 
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
 
Troubleshooting done:
 
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed

View 4 Replies View Related

Linksys Wireless Router :: Wrt54gs - Extend Wifi / Configure Devices For Ssid

Feb 16, 2012

I have two WRT54GS routers. I want to extend my WiFi from the router connected to my upstream in the office to a second router in the living room. I want devices configured for the SSID and passphrase of my current WiFi (which is find in the office) to work seamlessly in the living room. I understand I can do this by running a cable and configuring router 2 as a client of router 1 with router 2 exposing the same SSID and passthrase on a different channel.
 
But I really don't want to run a cable.There is a point where a client can see router 1 where an AP would cover the living room.
 
Can I put router 2 at that point, have it connect wirelessly as a client to router 1, and have it expose as an AP using the same SSID and passphrase? Can this be done without wiring the router?

View 1 Replies View Related

Linksys Wireless Router :: E4200 - Not Allow Connection To Devices When SSID Broadcast Is Turned Off

Jan 26, 2012

E4200 not letting my known wireless devices connect when SSID Broadcast is turned off.

View 1 Replies View Related

Cisco :: Rename An Existing Ssid On Aironet 1142

Sep 19, 2011

I wonder if there is a way to rename an existing SSID on aironet 1142 without destroying/recreating. I tried downloading configuration/ changing name/ re-uploading however that didn't have desired effect. There doesn't seem to be a way via web-GUI.

View 3 Replies View Related

Cisco :: Make SSID Hidden Aironet 1260?

Mar 28, 2013

We have three Access Points, two Cisco Aironet 1260 and one 1240AG. Originally, the SSID was hidden on all three AP's and users had to go to Other Networks and type in the SSID and password to access the WAN. About a few months ago, the network started broadcasting to the public. I am trying to make the SSID hidden again. I have tried going to the Security tab, choosing the  SSID Manager and setting single guest mode to none but it has not worked.

View 4 Replies View Related

Block Iphone / Devices From Getting IP Address From DHCP?

Feb 23, 2012

I've came across IP address that aren't enough for some users in the company. The IP addresses are more than enough to cater to the user's notebook or PC. However, some users does not know that there are actually limits to the IP we have, so quite a number of them actually uses their mobile / pads to tap the company's wireless.

I was wondering if i could restrict that particular user from tapping onto the network. I know it sounds a bit impossible because DHCP doesnt have that smart function to block whoever we sees deemed as a "nuisance".

View 29 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved