How To Configure Cisco Aironet 1252
Mar 7, 2013I'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .
View 9 Replies
ADVERTISEMENT
Cisco Aironet 1252 Configuration?
Mar 7, 2013Okay, I'm working on a project and the company I work for wants to add 5 Ghz antenna's to their Aironet 1252's. Okay not a problem, except I've never worked with these routers before and I can't get the configuration set (). Once I get 'em on one I can get them all done.
View 14 Replies View RelatedCisco :: Aironet 1252 AES Encryption?
Dec 5, 2012I have two cisco airenet 1252 autonamous access point that are configured as point to point bridge. Now I want to confiure AES encryption or WPA2 using a pre-shared key however I do not see the option to do this . The only option I see under ciphers are:
wep 128
wep 40
TKIP
[Code].....
Is it possible to use either AES or WPA2 using a pre-shared key on the 1252 autonamous access point? preferably using the web interface.
Cisco Wireless :: Aironet 1252 Bridge And 802.11n?
Dec 5, 2012I have two Cisco Aironet 1252 that I want to configure as a point-2-point bridge. Now I want to know if this configuration supports the 802.11n protocol.
View 2 Replies View RelatedCisco :: SNMP OID For Monitoring CPU On Aironet 1252
Jan 27, 2013I am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View RelatedCisco Wireless :: Aironet 1252 Boot Error
Jun 11, 2012an Aironet 1252 which is failing on boot. When power on the access-point shows the error below.
WARNING: A memory error occurred during the system start-up self-test. The device must be serviced if the error persists.
The following commands can, optionally, be used to initialize the flash file system and the TFTP file transfer system:
But when this happen, I can start the IOS manually doing flash_init and boot in ROMMON. After do this commands, the access-point starts and works normally.
How can I check and correct the memory and solve this issue?
Cisco Wireless :: Antenna Alignment On Aironet 1252
Oct 27, 2012I am using two Cisco Aironet 1252 (cisco AIR-AP1252AG-A-K9) to setup a point to point link (one is configured as root bridge and is as a non-root bridge). Both Aironets are running software version Version 12.4(25d)JA.
Is there a way that I can that I can perform an antenna alignment test on the Aironet that is configured as a non-root bridge?executing the following command dot11 dot11radio 0 ? does not show the antenna-alignemnet option.
Cisco Wireless :: VWLC And Aironet 1252 - All Client Devices Such As IPhone / Laptop Can't Find SSID
Sep 6, 2012I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
Cisco Wireless :: Aironet 1252 / Actual Wireless Link Speed Low
Nov 8, 2012I have 2 cisco Aironet 1252 setup as a point to point link using an external antenna (one radio is setup as the root bridge the other is setup as the non-root bridge). Now I see that the connection between the radios is established at a speed of 54 Mbps. However when I perform a speedtest on the link I see that the my actual download speed does not exceed the 2,5 Mbps. what can cause my actual speed to be far lower than the 54 Mbps? And what can I do to improve it?
View 16 Replies View RelatedCisco Wireless :: 1252 LAP - Configure Additional Antenna
Aug 20, 2012I would like to add an additional antenna to a 1252 LAP but I'm unsure of a few things...
I know this LAP currently has at least a yogi directional antenna (AIR-ANT2410Y-R) and also a ( AIR-ANT2485P-R) connected to it. The access point is in a ceiling so I cannot view the connections but according to this data sheet, { URL } each of the antennas I've specified require 3 per AP. I am only aware of 1 of each being used so not sure why 3 would be required?
Also on my 1252 1 side has 3, 2.4Ghz connections for antennas, TX, TX&RX, and RX. If I want to only use 1 AIR-ANT2410Y-R, would this be connected to the TX&RX port? Do all antennas support transmit and receive or are there some that only support TX and others that only support RX or is this based only how you configure the antennas? On the other side of the access point there are 3, 5Ghz antenna connections.
Cisco Wireless :: Configure Different SSIDs For Both Bands On 1252 And WLC?
Sep 9, 2012I found a few older forum posts and documents online discussing how to create multiple SSIDs on 1 1252 AP using the WLC and they state that VLANs are needed for the interface and then I've read that multiple SSIDs on 1 interface are also possible. I'm not sure on how to actually configure this. I would like my 2.4Ghz radio on the 1252 to be associated with the current SSID in production and the 5Ghz band associated with another SSID that's in production. I couldn't find an option in the WLC or anything stated in the documents I've read about how to associate the radio band with the SSID.
View 5 Replies View RelatedCisco :: Aironet 600 - Can't Configure OfficeExtend
Aug 7, 2012I just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
Cisco :: Configure SNMP On Aironet 1130?
Jul 21, 2011I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View RelatedCisco :: Configure Aironet 3500i Without WLC Controller?
Nov 30, 2011if i can configure the cisco aironet 3500i without WLC controller.
View 1 Replies View RelatedCisco Wireless :: Configure Aironet 1100 Series AP?
Apr 1, 2013I have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedCisco Wireless :: Can't Configure Aironet 1142N With Web Interface
Jan 17, 2013I have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
Cisco :: Configure Aironet 1040 Access Point?
Oct 27, 2011I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below
%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
and the ssid is not getting broadcasted. kindly let me what could be the cause.
[code]....
Cisco Wireless :: Aironet 3502I - How To Configure Device
May 14, 2012I have a newly purchased Aironet 3502i that I would like to configure on my network. I am new to Cisco networking in general, and would like to know how to configure the device to operate without a WLAN Controller.
View 4 Replies View RelatedCisco Wireless :: Aironet 1310 Bridge - Cannot Access GUI To Configure
Nov 21, 2011I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
Cisco Wireless :: Aironet 1040 How To Configure Access Points
May 21, 2012I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
Cisco Wireless :: Configure ASA 5505 And Aironet 1140 Multiple SSIDs?
Jan 10, 2012I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedCisco Wireless :: Aironet 1130 AG - Unable To Enter Configure Mode
Sep 14, 2011I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
Cisco Wireless :: Aironet 600 OEAP / AP Is Able To Configure 2 Public IP Address Of DMZ-WLCs?
Dec 9, 2012Does the AP is able to configure 2 public ip address of the DMZ-WLCs?
like ip 1.1.1.1 in my US data center, whereas a second ip 2.2.2.2 in my EU data center?
Cisco Wireless :: Configure Multiple SSID On Aironet 3600i AP Via 2504 Controller
Apr 3, 2012Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedCisco :: 1252 LAP Won't Join WLC
Jul 18, 2009I'm having an issue with a 1252 LAP that is connected to the WLC over a WAN link.Basically, it won't associate. The following is taken from a console into the LAP:
*Mar 1 00:00:07.799: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:08.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.851: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.003: Logging LWAPP message to 255.255.255.255.
[code].....
The ap-manager interface is configured correctly and there isn't a duplicate IP address. The LAP was initially stand alone and was converted to LWAPP.The MTU over the WAN link is 1500 bytes.All I'm getting from the WLC debugs is:
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Received LWAPP DISCOVERY REQUEST from AP 00:22:xx:xx:xx:xx to 00:19:xx:xx:xx:xx on port '29'
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx LWAPP Discovery Request AP Software Version: 0x3003300
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Successful transmission of LWAPP Discovery Response to AP 00:22:xx:xx:xx:xx on port 29
So basically the join messages don't seem to reach the WLC. In fact they don't even seem to reach the local router on the remote subnet. The discovery packets are seen on the local router but the joins don't seem to appear at all.I'm not sure if it's a latency issue. Average latency over the WAN link is under 70ms.I'm assuming the certificate on the WAP is MIC and the MAC details have been entered into the WLC AP Security policies for authentication. I'm not seeing any debugging messages relating to bad authentication at all.I can't debug from the LAP as it's LWAPP, obviously.We're running WLC version 4.2.130.0.
Cisco WAN :: 1252 On SGE2000P Via PoE?
Mar 15, 2011it is possible to wide the range of powerconsumtion on this switch from 15.4W up to 20W? We will rollout some accesspoints with 2 radiomodules on CISCO AP1252, but the Powerconsumtion of this AP then ist 18.5W. The max allowed from firmware is 15.4W like 802.11n-standard.
View 1 Replies View RelatedCisco Wireless :: DHCP Not Assigning IP To 1252 AP?
Dec 16, 2010I am replacing an older AP with a new 1252 unit. I attached everything and powered it up, but my DHCP server does not appear to be finding it and assigning an IP address. The status light stays green and the ethernet light blinks randomly green. Seems to be connected fine, but without an IP I cannot configure it to use it.
View 2 Replies View RelatedCisco :: User Connects To Weaker 1252 AP?
Mar 25, 2013I have Cisco 1252 APs in my network and also a WLC with software 7.0.98.0 and a WCS system. In certain areas I have an SSID with 2 or more APs configured as part of the group. Some users are connecting to the SSID on the weaker AP when there is a much stronger signal available from a different AP.I have looked into this issue before and have been told it's a porblem with the client's Wireless NIC or the drivers. The issue is I'm using the most updates drivers on some users and it makes no difference. Although it may be a problem with my clients I need to fix this on Cisco's AP side. What are my options? I believe MAC filtering is only per SSID so that would defeat the purpose, can I filter by specific AP and still allow the user to connect to the SSID? Or should I seperate the APs from the 1 SSID and create multiple SSIDs so the user can select the stronger network?
View 4 Replies View RelatedCisco Wireless :: How To Connect Laptop To LAP 1252 With WLC 7.0
Feb 17, 2013How can i connect my laptop (11n supported) to LAP 1252 with WLC 7.0.116.0?Status: 11a enabled on wlcDCA channel list in 11a on wlc is showing only 149 153 157 161 channels.
View 6 Replies View RelatedCisco Wireless :: AP 1252 Boots Into ROMmon
Jul 17, 2012I have a lightweight AP that boots into RoMmon, if i hold the reset button in for 10 seconds or so it will boot into the IOS and download the config from the controller but never registers. then once i reboot it it goes back to Romon unless i hold in the button again.
View 5 Replies View RelatedCisco :: 1252 Wireless AP Resetting To Factory Default
Jan 5, 2012I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedCisco Wireless :: Change IOS Of 1252 LWAP AP To Autonomous AP?
Jun 20, 2011Is it possible to Change IOS of 1252 LWAP AP to Autonomous AP? I have seen some documents for changing Autonomous AP to LWAP and change back procedures.
View 4 Replies View RelatedCisco Wireless :: 1252 - Automated Racking System
Jul 1, 2012we want to have full wireless coverage in a big warehouse (120mx90m) and 15 meter Height that will be having big racks (14 meters height) and 2 meter between the racks and the rack itself is 1.5 meter (2 rack back to back), now we will be having scanners and we need to make sure the wireless is covering everywhere.Where is the best place to put the AP, Ceiling? How Many APs per row ? each row will be around 60 meters length.
Is AP 1252 a good choice? The scanners are a/b/g.What i'm thinking of is to put 1 AP per row mounted on the ceiling and antennas facing down because it is hard to mount the APs between the rack because of the automated racking system.