Does the AP is able to configure 2 public ip address of the DMZ-WLCs?
like ip 1.1.1.1 in my US data center, whereas a second ip 2.2.2.2 in my EU data center?
Possible to assign reslient WLCs to an OEAP 600?
The web GUI of the OEAP itself only has a single field to enter the address of a single controller.
But, I wonder if once the OEAP is talking to your WLC across the Internet, you can allocate HA settings to the OEAP so that it can fall back to a secondary WLC if your main WLC fails.
This is sort of hinted at in the docs I have read, but I have not been able to find it explicitly stated anywhere.
It would be nice to have 2 DMZ-based WLCs at two different data centres to allow remote users to have a fail-over solution, but I need to be sure that this is supported before implementing.
I have found that there are only few configuration to the Cisco Aironet 600 OEAP. The settings are just for basic configuration for a wireless network when it is in autonomous mode.
A need for a Wireless LAN Controller to perform advance settings.
Also, there are no firmware available in Cisco. No upgrade/downgrade firmware avalaible for download.
i received a public ip from my ISP and need to configure to enable access my server remotely
View 1 Replies View RelatedI have an aironet 1242, It must be connect to an DSL using a static Public IP, and this AP must provide dhcp services, how to configure this access point in order to be connected to Internet using Public IP and provide dhcp service.
View 4 Replies View RelatedI have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
I have a newly purchased Aironet 3502i that I would like to configure on my network. I am new to Cisco networking in general, and would like to know how to configure the device to operate without a WLAN Controller.
View 4 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedI just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
How do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies View RelatedCan I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View Relatedi got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?
View 4 Replies View RelatedI have noticed that after the new Firmware Update, the EA4500 will not change to a new public address. I have check my logs and my IP Address is the same going back to a 03/25/2012. I changed my router back to my old E4200V1 and it changes to a new addresses when the old one expires.
View 3 Replies View Relatedwe have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies View RelatedWe have cisco 5508 office extend in dmz running code 7.3.112. 1132 AP seems to register and authenticate fine but OEAP 600 series dont seem to authenticate. they seem to join the controller and download the SSID but just wont authenticate ? not even registering on the AAA server
View 9 Replies View Relatedhave concern regarding the faiolver of 2 WLCs.
1. One Active_WLC(2504) have a full licence of 15 Access points.
2. 2nd Seconday_WLCs(2504) have a normal licenece (Without any AP licenece-Zero AP Count License).
Now my questions are:
1. If first WLCs goes down due to any kind of problem then can secondary WLCs comes up and takover of all APs.
2. if Yes, then How may days or hours...These APs will connect to the WLC.
3.If first WLCs comes up after some days, then can this WLC automaticall tak over the situation??
Here's the list of equipments:
Pool of oeap 600 aps
1x 2504WLC as OEAP WLC (@DMZ)
1x ASA 5515
Scenario:
My OEAP WLC located at ASA - DMZ is NATted to a public ip (primary internet ISP), then my pool of OEAP-600 were configured to communicate with this OEAP WLC.
My question is:
I want to automate the failover of OEAP-600 (I don't know if this is possible) to the secondary internet ISP whenever the primary internet ISP fails. The secondary ISP is terminated on the same ASA 5515-X doing PBR and IP SLA stuff.
I know that OEAP 600 can only be pointed to one WLC ip address I know that the WLC can only be NATted to one public IP address.
What would be the best solution to perform the OEAP backup connectivity? Or just buy another set of WLC/ASA then just manually configure the OEAP-600 APs to point to the secondary ISP.
I'm using two 5500 WLCs with the version 7.2.110.0 When some AP with the part number AIR-CAP1552E-N-K9 associate with them, the 802.11g stays up and the 802.11a stays down.I saw the AP interfaces in Wireless --> All APs and the 802.11a is down and the regulatory domain show me not supported but the 802.11g is working normally.I follow this document from Cisco [URL] and i just have BR - Brazil to support this part number.
View 5 Replies View RelatedI've just been tasked with setting up 19 AIR-CT2504 WLCs with AIR-CAP3502E APs. The primary objective is to maximize throughput from clients uploading LARGE files over the air.
I need to make sure I config HT 802.11n properly with no support for legacy clients in the 5Ghz band.
How to Configure VPN SERVER with Public IP. Is there any free and secure tool so that we can create multiple vpn client and access the vpn network, Requirement Only one public Ip.
View 3 Replies View RelatedI have a customer looking to deploy OEAP & wants to know if it possible to disable the local ports 1-3? Reason being, they don't want the home user connecting devices & causing more support tickets to troubleshoot an Xbox or Google TV just b/c it's connected to a company provide AP/Switch. I have read all the docs & it makes no mention of this.... I can see in 7.2 the ability to disable the local SSID but no mention of the ability to shutdown ports 1-3..Also see support in 7.2 for Dual RLAN... but that still leaves 2 local ports.
View 5 Replies View RelatedI have some trouble with the setup of an oeap 600 ap. The ap has joined the controller as it should and the remote-lan connection to my corporate network works well, but i can't connect to the corporate wlan.
When i check the event log on the ap it says:
"
*Oct 02 07:36:56.662: (Re)Assoc-Req from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:36:56.665: received assoc-rsp for wireless client, status=0011
*Oct 02 07:37:11.712: DisAssoc-Req/DeAUTH from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:37:11.713: WTP Event: Delete Mobile sent to wlc00:1a:73:d2:82:8c"
and a debug on the controller gives me:
apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Adding mobile
on LWAPP AP ec:c8:82:c2:3a:20(0)
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Association received from mobile on AP ec:c8:82:c2:3a:20
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Sending Assoc Response to station on BSSID ec:c8:82:c2:3a:20 (s
tatus 17) ApVapId 1 Slot 0
[code]....
I'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .
View 9 Replies View RelatedI just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
I have a set of public ip(/29) using adsl2+, is it possible to config cisco 857 as a public gateway so i can assign public ips to my computers?? before i upgrade to adsl2+ i was using cisco 678, it can be config as a public gateway without problem, but now i have ot use adsl2+, can't use cisco 678 anymore..
View 8 Replies View RelatedI have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
Only fifteen users are allowed to connect on the WLAN Controller WLANs provided on the 600 series at any one time. A sixteenth user cannot authenticate until one of the first clients de-authenticates or a timeout occurred on the controller. Note: This number is cumulative across the controller WLANs on the 600 series. For example, if two controller WLANs are configured and there are fifteen users on one of the WLANs, no users will be able to join the other WLAN on the 600 series at that time. This limit does not apply to the local private WLANs that the end user configures on the 600 series designed for personal use and clients connected on these private WLANs or on the wired ports do not affect these limits. This is from the Configuration Guide for teh 600 series Office Extend AP. Is this count per AP or total per WLC? If I have 10 APs deployed to our remote users, can each AP support two simultaneous users? Would I need to use separate WLANs for each OEAP?
View 8 Replies View RelatedI've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable.
View 18 Replies View RelatedI need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View Related
