I have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
I just purchased an Aironet 1142n and need to configure/set it on one subnet in our WAN and ship it to another subnet on the WAN.
I have not been able to access the unit using a network cable from a pc direct connected to the Aironet. The pc's ip address is set to 10.0.0.2 I can not get to the access point thru the web interface using 10.0.0.1.
When I attempted to access it using a Hyper terminal connected to serial port and console port it loaded a list of software and updates and then reported that it shut down and I could not do any thing with it.
What must I do to be able to configuer a static IP and assign it an SSID and Security settings? How can I access the web interface? I have reset it by uplugging the power cord and holding down the Mode button while I plugged back in the power cord and holding it until the light turned amber/orange. Currently the light is solid green with the ethernet port direct connected to the nic card on a desktop.
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies View RelatedI've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
I just Bought 1142N AP, I am unable to connect to it or open its Web interface, the Default IPs i am using are 10.0.0.1 for Router and 10.0.0.2 for my PC, whats its Default IP, What IP address should I put on PC, plus Do i need the IOS for the AP?
View 3 Replies View RelatedWe have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
A Cisco RV220W router/firewall connects the local LAN to the internet. The router is connected to a new Cisco SG300-28P switch configured in Layer 2 mode. There are two new AIR-1142N wireless access points running in autonomous mode connected to 2 ports on the SG300 powered through PoE. The AIR-1142N access points are running the latest firmware version 15.2(2)JB. There are two VLANs defined: VLAN1 is the native on all devices, and VLAN2 is for wireless guest traffic to provide access to the internet only.Internal/staff traffic is on 192.168.100.x, and the wireless SSID is MYNetS.Guest traffic is on 192.168.200.x and the wireless SSID is MyNetG.IP addresses are being assigned by the RV220W.
All works well with one exception. Wireless clients on the internal SSID are able to ping/access the switch, router, and other clients on wired ports on the switch. The router, switch, and wired clients can ping wireless clients. However, wireless clients, on the same SSID and the same 1142N cannot ping/access one another. They are being isolated from each other. We absolutely need to have this capability.The SG300 does not have port security enabled on any port. none of the workstations/laptops have a firewall enabled. These laptops are all Macs btw. I have checked that neither of the 1142N access points have Public Secure Packet Forwarding enabled on either of the VLANs.I am at a loss as to why the wireless clients are being isolated.
I am trying to configure an Aironet 1142 WAP model#AIR-AP1142n-A-K9. My setup is very basic, I have a router that acts as the DHCP server, the 1142n, and a PC. I am using the 1142n in Standalone AP mode no authentication, and have it working according to the [URL]. And it is working perfectly. My questions are as follows.
1. I have isolated the wireless users from seeing each other by using ap isolation, Can I prevent the wireless users from accessing the lan pc, router and WAP configuration pages? Is there any way to do that while still maintaining internet access? Basically I just want to provide my users wireless internet access without authentication but don't want them able to see each other or anything on the lan.
Does Cisco 1142n Aironet Access Point support WPA-PSK with AES encryption ?
View 1 Replies View RelatedI have 14 unit of Air-AP1142n. No controller. All unit were in a warehouse, each of the AP distance each other around 40mI would like to use only 4 SSID instead of 14 SSID.
View 5 Replies View RelatedI have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
I'm trying to configure an 1142N AP + 2960-S + ASA5505 with wireless, vlans and trunking with no success. DHCP is provided from my DHCP-server on the inside.
View 4 Replies View RelatedWe have 4x AP1142 standalone APs in WDS mode with roaming and RADIUS from Windows AD for auth.Everything works as expected apart from two APs that frequently reset Dot11Radio0 interface. The other two are fine.
The config on all APs is identical, version of IOS is the same accross all APs (12.4(23c)JA3). The only way to get reset inteface back up is to "reload". [code]
I have very little practical knowledge of routers, switches and AP's. I recently got a very old Cisco Aironet 1100 series AP which was working fine in one network. I reset it and tried configuring it in new network (uses DHCP to assign public IP) for school use. But not able to access internet.
View 3 Replies View RelatedI have a newly purchased Aironet 3502i that I would like to configure on my network. I am new to Cisco networking in general, and would like to know how to configure the device to operate without a WLAN Controller.
View 4 Replies View RelatedHow can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies View RelatedI have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
Our office has 4 Cisco Aironet 1140 access points mounted on the ceiling. They are all powered via PoE. Every few days 3 of the 4 access points hang and have to be rebooted. When they hang I am not able to connect to their web interface to check the logs. The fourth, for some reason, always seems to stay alive.
I checked the configuration for all AP's and "Hot Standby" is disabled They are all using static IP addresses. I've tried 2 different banks of static IP addresses and 3 of 4 still hange so I don't think this is an IP conflict. I have saved the configurations and compared them and they are all identical, where possible.
They all have software version: 12.4(21a)JA1
They all have bootloader version: 12.4(23c)JA1
I have tried to download the latest software/firmware, but unfortunately I do not have a valid service contract in place with Cisco and therefore can't download the latest version. All of our CISCO hardware was purchased from Amazon resellers but no luck. I have also tried to contact Cisco and they can't seem to assist either. How I can get a valid service contract that information would also be very useful!!!
why 3 of our 4 access points would hang? When they hang, I can't login to the web interface and the logs seem to reset when I reset each access point. I have also set up an rsyslog server and I don't see a log entry that would indicate a problem.
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedI just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
Does the AP is able to configure 2 public ip address of the DMZ-WLCs?
like ip 1.1.1.1 in my US data center, whereas a second ip 2.2.2.2 in my EU data center?
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View RelatedI'm trying to configure my Cisco Aironet 1252's in my office to utilize their 5GHz antenna's but I've never worked with these routers before .
View 9 Replies View RelatedI just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View Relatedif i can configure the cisco aironet 3500i without WLC controller.
View 1 Replies View RelatedOn an AIRONET 600 AP (officeExtend) with the remote LAN interface is configured to use 802.1x authentication:If a Cisco IP Phone is connected, 801.x authentication challenges for credentials. The AP does not seem to have a way to detect that this is an IP Phone and to skip the challenge (as Cisco switches/routers would do) Is there any way around this? Can the remote LAN interface be configured to skip authentication for IP Phone and only authenticate PCs etc..?
View 5 Replies View RelatedI am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below
%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
and the ssid is not getting broadcasted. kindly let me what could be the cause.
[code]....
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
Is there a way to configure the GIG 0 interface on the 1552E Access Points to 10 Meg Full Duplex? Currently they will only work in Auto/Auto
View 3 Replies View RelatedI have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?