Cisco Wireless :: Cannot Get Access To New Aironet 1142n
Apr 16, 2013
I just purchased an Aironet 1142n and need to configure/set it on one subnet in our WAN and ship it to another subnet on the WAN.
I have not been able to access the unit using a network cable from a pc direct connected to the Aironet. The pc's ip address is set to 10.0.0.2 I can not get to the access point thru the web interface using 10.0.0.1.
When I attempted to access it using a Hyper terminal connected to serial port and console port it loaded a list of software and updates and then reported that it shut down and I could not do any thing with it.
What must I do to be able to configuer a static IP and assign it an SSID and Security settings? How can I access the web interface? I have reset it by uplugging the power cord and holding down the Mode button while I plugged back in the power cord and holding it until the light turned amber/orange. Currently the light is solid green with the ethernet port direct connected to the nic card on a desktop.
View 4 Replies
ADVERTISEMENT
Apr 3, 2013
A Cisco RV220W router/firewall connects the local LAN to the internet. The router is connected to a new Cisco SG300-28P switch configured in Layer 2 mode. There are two new AIR-1142N wireless access points running in autonomous mode connected to 2 ports on the SG300 powered through PoE. The AIR-1142N access points are running the latest firmware version 15.2(2)JB. There are two VLANs defined: VLAN1 is the native on all devices, and VLAN2 is for wireless guest traffic to provide access to the internet only.Internal/staff traffic is on 192.168.100.x, and the wireless SSID is MYNetS.Guest traffic is on 192.168.200.x and the wireless SSID is MyNetG.IP addresses are being assigned by the RV220W.
All works well with one exception. Wireless clients on the internal SSID are able to ping/access the switch, router, and other clients on wired ports on the switch. The router, switch, and wired clients can ping wireless clients. However, wireless clients, on the same SSID and the same 1142N cannot ping/access one another. They are being isolated from each other. We absolutely need to have this capability.The SG300 does not have port security enabled on any port. none of the workstations/laptops have a firewall enabled. These laptops are all Macs btw. I have checked that neither of the 1142N access points have Public Secure Packet Forwarding enabled on either of the VLANs.I am at a loss as to why the wireless clients are being isolated.
View 5 Replies
View Related
Oct 8, 2012
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies
View Related
Aug 9, 2012
I've just recently purchased the Aironet 1142n and am hoping to set it up as a repeater. I've followed the documentation here: [UEL] but am still having problems.
What I'm trying to achieve is: I have an adsl router (TP-link W8960N) at the front of the house but the wireless signal does not reach all the way to the end of the house. I am trying to set up the aironet 1142n to act as a repeater and place it in the middle of the house and hopefully that will extend the wireless signal to the end of the house and remove the dead spots. I would like to do this without having ethernet cables running all over the place and have been trying to configure the aironet 1142n to no avail. Every time I set the aironet 1142n to "repeater" it automatically coverts back to "access point" under role of radio network.
I guess my main question first of all is, can I set the aironet 1142n as a wireless repeater? And if so, where am I going wrong in my configuration?
I've just read that " Repeater access points running Cisco IOS software cannot associate to parent access points that that do not run Cisco IOS software."
Does this mean the aironet 1142n set up as a repeater will not work if the original access point (in this case, the TP Link adsl wireless router) isn't a cisco brand?
View 3 Replies
View Related
Jan 17, 2013
I have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
View 2 Replies
View Related
Jan 8, 2013
I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
View 19 Replies
View Related
Dec 5, 2012
I just Bought 1142N AP, I am unable to connect to it or open its Web interface, the Default IPs i am using are 10.0.0.1 for Router and 10.0.0.2 for my PC, whats its Default IP, What IP address should I put on PC, plus Do i need the IOS for the AP?
View 3 Replies
View Related
Sep 6, 2012
We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
View 7 Replies
View Related
Oct 21, 2011
I am trying to configure an Aironet 1142 WAP model#AIR-AP1142n-A-K9. My setup is very basic, I have a router that acts as the DHCP server, the 1142n, and a PC. I am using the 1142n in Standalone AP mode no authentication, and have it working according to the [URL]. And it is working perfectly. My questions are as follows.
1. I have isolated the wireless users from seeing each other by using ap isolation, Can I prevent the wireless users from accessing the lan pc, router and WAP configuration pages? Is there any way to do that while still maintaining internet access? Basically I just want to provide my users wireless internet access without authentication but don't want them able to see each other or anything on the lan.
View 2 Replies
View Related
Jun 19, 2011
Does Cisco 1142n Aironet Access Point support WPA-PSK with AES encryption ?
View 1 Replies
View Related
Jun 13, 2013
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies
View Related
Feb 27, 2012
configuring DHCP on access point, i have cisco 1142N access point, in my network.. working in autonomous mode, i have assigned a static ip to access point with default gateway.. from AP i'm able to reach internet and user connecting to access point are not able to get ip.. i have DHCP server in my network. how to make access point to fetch ip from my dhcp server and assign the saem to client.
View 10 Replies
View Related
Apr 29, 2013
I've got a Cisco Aironet LAP1310AG-A-K9 that I can't access through Internet Explorer or Firefox (multiple versions). I set a static IP in DHCP, I can ping the unit, but I can't browse to the GUI.
View 1 Replies
View Related
Dec 29, 2012
I can no longer open a http or https connection to the AP. I do have ssh access and I can log in with full privileges.
I was using the Web interface a few days ago and it did something strange during an update. The display of the web page became corrupted and no longer responded to my input.
I restarted it from an ssh session and I have also power cycled it via the power injector. Neither method has worked.
What should I do next or what additional info can I provide from an ssh shell?
Physical access is very difficult. It requires a 30' ladder after 10 p.m. So, I would like to avoid that if possible.
View 7 Replies
View Related
Mar 19, 2011
I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.
The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?
View 2 Replies
View Related
Oct 13, 2010
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies
View Related
May 22, 2012
We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
View 5 Replies
View Related
Nov 21, 2011
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
View 3 Replies
View Related
May 21, 2012
I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
View 16 Replies
View Related
Sep 13, 2012
I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
View 1 Replies
View Related
Mar 13, 2013
I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
View 4 Replies
View Related
Apr 9, 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
View 2 Replies
View Related
Feb 12, 2011
I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
View 7 Replies
View Related
Jan 3, 2013
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
View 2 Replies
View Related
Dec 22, 2009
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
View 2 Replies
View Related
Sep 25, 2012
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
View 2 Replies
View Related
Dec 1, 2010
I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies
View Related
Mar 16, 2013
I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.
View 5 Replies
View Related
Mar 19, 2013
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies
View Related
Dec 30, 2012
we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.
View 17 Replies
View Related
Feb 12, 2013
In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
View 3 Replies
View Related
Jul 19, 2012
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
View 9 Replies
View Related
Jul 15, 2012
We are in need to perform a site survey with the Aironet 1041N Access Point.
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?
View 2 Replies
View Related
