Cisco Wireless :: Aironet 2602e Configuration As Standalone Access Point

Mar 19, 2013

I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: AIR-LAP521-G-E-K9 Access Point Configuration In Standalone Mode

Aug 3, 2011

how to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.

View 4 Replies View Related

Cisco Wireless :: AIR-SAP-1602i-k9 Aironet Standalone Configuration?

Jun 11, 2013

I have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
 
I tried seeing if it would pull a DHCP address on my network but it didnt.

View 1 Replies View Related

Cisco Wireless :: Access Point 2602e Antennas Dual Band

Apr 9, 2013

I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:

• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
 
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?

View 9 Replies View Related

Cisco Wireless :: Aironet 1041N Standalone Access Points Setup Information

Jul 19, 2012

I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.

The reason why I'm writing is because I have a few questions to clarify.  
 
1) What is the best position for better signal, top side wall or corner ceiling?
 
2) How many client mac address filtering  can i do per access point?
 
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.

4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)

5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?

6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?

7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.

8) Can CCp software be used in these access points?

View 9 Replies View Related

Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?

Jun 25, 2012

I can't figure out how to get the config right for the 802.11n channel to work.

View 4 Replies View Related

Cisco Wireless :: AIR-AP1231G-A-K9 Standalone Access Point- Disconnection

Jun 9, 2013

We have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.

View 2 Replies View Related

Cisco Wireless :: Convert Standalone 1600 Access Point To CAPWAP Based AP

Mar 20, 2013

Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs

View 1 Replies View Related

Cisco :: Standalone Aironet 1140 - VPN Not Working Over Wireless

Dec 19, 2010

I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior.  I'm having one issue that I can't figure out though.  None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless.  If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
 
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
 
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
 
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC   authentication open    authentication key-management wpa   guest-mode   mbssid guest-mode   wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed  basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed  basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]

View 9 Replies View Related

Cisco Wireless :: Aironet 1600 - Standalone Or Autonomous

Mar 18, 2013

It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?        

View 3 Replies View Related

Cisco Wireless :: Aironet 2600 In Standalone Mode

Feb 18, 2013

I have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL

I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.

View 22 Replies View Related

Cisco Wireless :: Aironet 1140 Standalone AP To Have Radio Management

Dec 28, 2011

For some time now I have been looking for a good business class wireless AP. I've narrowed it down to the Cisco Aironet 1140 standalone (no controller). I'm no stranger to Cisco products. I've worked with their routers, switches and Pix/ASA firewalls. However, I've not had the opportunity to work with their wireless AP's. Anyone using these AP's (more specifically the 1140 standalone), can provide information on the reliability and security of these devices. Some of the features I would like to have like Radio Mgmt. and Rogue AP Detection I see are only available on the controller based units. Does not having these features on the standalone unit reduce its reliability and security? This is for a small business and the budget does not allow to drop for a controller at this time.

View 7 Replies View Related

Cisco Wireless :: How To Setup A Standalone Aironet AP 1260 Series

Sep 13, 2011

I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?

View 3 Replies View Related

Cisco Wireless :: Aironet 1600 Standalone WAP / How To Get Clients Connected

May 15, 2013

I just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
 
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
 
No one can connect to the 5 Ghz radio.
 
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
 
I am on the latest version of the firmware.

View 1 Replies View Related

Cisco Wireless :: Aironet 1142 Standalone AP And Apple Bonjour Service

Aug 7, 2012

I am using an Aironet 1142 standalone AP and want to use Apples Bonjour Service between iOS devices e.g. iPad and Apple TV.I have found here some posts that suggest to disable igmp snopping but this didn't worked for me.All devices are in the same vlan/subnet. Do I need to configure something special?

View 3 Replies View Related

Aironet AIR-AP1252G-A-K9 - Wireless Access Point

Mar 19, 2011

I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.

The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?

View 2 Replies View Related

Cisco Wireless :: Aironet 1130AG - Login To Wi-Fi Access Point?

Oct 13, 2010

I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.

View 3 Replies View Related

Cisco Wireless :: Aironet 1040 Access Point Managing

May 22, 2012

We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.

View 5 Replies View Related

Cisco Wireless :: Aironet 1310 - Outdoor Access Point

Sep 13, 2012

I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
 
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it.  I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS.  I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?

View 1 Replies View Related

Cisco Wireless :: Setting Up Aironet 1040 Access Point

Mar 13, 2013

I'm working on setting up an Aironet 1040 Wireless Access Point for my company.  It's my first time setting up something like this, and I've run into a bit of trouble.
 
I created my first SSID easily enough, following the manual and guides online.  I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great.  However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
 
I created VLAN 2, and then another SSID which I linked here.  I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager.  I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'.  I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.

View 4 Replies View Related

Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?

Apr 9, 2012

I want to connect two buildings. Let's call them Building A (main) and Building B.
 
 „A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
  
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
 
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
 
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
  
My Questions:
 
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?

2. How Do I tell AP03 that it should use AP02 as a gateway to building A?

View 2 Replies View Related

Cisco Wireless :: 1242AG / Maximum Associations In Aironet Access Point?

Feb 12, 2011

I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.

Questions :

1.    What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?

2.       If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point

3.       I there a simulator tool that can be used to simulate multiple wireless connections to an AP

4.       Have anyone tested so many users connected to 1 Access point ?

View 7 Replies View Related

Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??

Dec 1, 2010

I would like to buy Cisco  Aironet 1260 Access Points, i just want to use them independantly so   i want to know do they work without the Wireless LAN Controller? or i  have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.

View 9 Replies View Related

Cisco Wireless :: Change IP Address Of Aironet 1200 Series Access Point

Dec 30, 2012

we have 6 access points in production and we want to chnage the IP addresses of them. So what would be the procedure for that.

View 17 Replies View Related

Cisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point

Feb 12, 2013

In our office, we have 3 Cisco Aironet 1140s and they are configured as follows: 

* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
 
how to have the Repeater connect to Access Point A only?

View 3 Replies View Related

Cisco Wireless :: Perform Site Survey With Aironet 1041N Access Point?

Jul 15, 2012

We are in need to perform a site survey with the Aironet 1041N Access Point.
 
Upon reviewing the site survey software, it seems you need to use an Aironet adapter. However from what i can tell, all the Aironet adapters are PCMICA cards, which most modern laptops do not have, and the PCMICA cards that do exist don't have drivers for windows 7.
 
Are there USB adapters w/ Windows 7 drivers that can be used to perform a site survey?

View 2 Replies View Related

Cisco Wireless :: Aironet 1310 - Infrastructure Access Point Unreachable For Management

Sep 16, 2010

We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings.  One went south on us & we placed it.  Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP.  Now, we can't connect or even ping either AP.  And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them.  I'm attaching the configuration.  Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?

View 3 Replies View Related

Cisco Wireless :: Aironet AP-1041N Setting To Have Access Point Broadcast Multiple SSIDs

Jan 17, 2013

I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?

View 1 Replies View Related

Cisco :: Airplay Support Aironet AP 1140 Standalone

Oct 12, 2012

We have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.

Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
 
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.

View 3 Replies View Related

Cisco Wireless :: Aironet 1310G - Point To Point Bridge

Oct 14, 2012

Is any one can configure basic Point-toPoint wireless bridge. I need to connect two simple LAN with Cisco Aironet1310 AP. I required basic configuration with basic authentication between these two devices which is on IOS "123-8.JEA3".

View 16 Replies View Related

Cisco :: Configuring Aironet 1100 Access Point?

Dec 22, 2011

I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?

View 8 Replies View Related

Cisco :: Configure Aironet 1040 Access Point?

Oct 27, 2011

I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below

%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
 
and the ssid is not getting broadcasted. kindly let me what could be the cause.
 
[code]....

View 3 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved