Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?
Jun 25, 2012I can't figure out how to get the config right for the 802.11n channel to work.
View 4 Replies
ADVERTISEMENT
Cisco :: Configure Aironet 1040 Access Point?
Oct 27, 2011I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below
%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
and the ssid is not getting broadcasted. kindly let me what could be the cause.
[code]....
Home Network :: Set Up Access Point Aironet 1040 Cisco?
Nov 23, 2012how i can set up access point aironet 1040 cisco?
View 2 Replies View RelatedCisco Wireless :: Aironet 1040 Access Point Managing
May 22, 2012We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
View 5 Replies View RelatedCisco Wireless :: Setting Up Aironet 1040 Access Point
Mar 13, 2013I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
Cisco Wireless :: Aironet 1260 Access Point Work Without Controller??
Dec 1, 2010I would like to buy Cisco Aironet 1260 Access Points, i just want to use them independantly so i want to know do they work without the Wireless LAN Controller? or i have to have the controller for them to work? they will be in different locations so i cant have a controller per each location.
View 9 Replies View RelatedCisco Wireless :: Aironet 1040 How To Configure Access Points
May 21, 2012I have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
Cisco Wireless :: Aironet 2602e Configuration As Standalone Access Point
Mar 19, 2013I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies View RelatedCisco WAN :: Wireless Cannot See The 1040 Aironet
Jan 8, 2013everyone can connect to the 1040 ap except my laptop and another one. for some reason it stopped showing , it was working fine and out of the blue nothing.
View 2 Replies View RelatedCisco Wireless :: Slow Connection With Aironet 1040?
Nov 15, 2012I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread ([URL]) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
Cisco :: Aironet 1040 And Radius Auth Failure?
Sep 24, 2011I have setup a Cisco Aironet 1040 to connect to our Radius server which I have also configured.
I can successfully connect up any Iphone or Ipad but I cannot get any laptop to connect.
I have attached the logs showing the Iphone Successfully logging in and the Laptop Failing. Every single failure in the Event log for NPS comes up with
Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information.
User:
Security ID: NULL SID
Account Name: scottd
Account Domain: AMSLAN
[Code].....
Cisco Wireless :: Configuring Aironet 1040 With WPA2-PSK?
May 24, 2012I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes
!
version 12.4
no service pad
[Code].....
Cisco Wireless :: How Many Clients Can Be Connected To Aironet 1040 AP
Jan 1, 2013i have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?
View 3 Replies View RelatedCisco Wireless :: Aironet 1040 IP And Splash Page Redirecting
Mar 11, 2013I am trying to create a welcome screen for people who join the guest network on my aironet 1040.Webpage pass-through is really what I want but I know that doesn't work on a 1040.What does: IP redirect, Conditional Web redirect or Splashpage redirect?
View 1 Replies View RelatedCisco Wireless :: Aironet 1040 Dual Band Disconnects Mac OS X
Dec 26, 2012we have several AP1040 in the office, but the latter is a Dual Band 2.4 GHz and 5 GHz. And we have problems with all workstations MAC OS X gets a lot of disconnections during the day, the strangest thing is that the OS X community is aware of the problem, and their only recommendation is to buy the external Aironport has better hardware.
View 3 Replies View RelatedCisco :: Samsung Android Phones Cannot Connect To Aironet 1040 Network
Dec 26, 2012Every device I've tried to connect to my WiFi network have no issues connecting at all, except for, as far as I can tell, Samsung Android phones. My sample set is very small, but both a Samsung Galaxy S3 (both before and after custom ROM install) and a stock Samsung Galaxy Nexus.
I've tried setting a vlan up with no encryption and open authentication, and the phones just halt on "connecting". This issue is both on the 2.4Ghz and 5Ghz Radios.
What is working is various computers with both intel and broadcom adapters, a Brother printer, and a Motorola Droid 3 and Motorola Photon Q. I'm starting to think that it's an issue with the radio in the Samsung phones, but the S3 is 5ghz compatible and the Nexus is only 2.4, so they must have different radios. I'm also pretty sure that it's not software on the phones since the S3 had the same problem with stock ROM and CM 10, and the Nexus is Vanilla Google ROM.
I'm waiting to get a chance to upgrade to the new FW for my aironet 1040, and I'm going to fire up an old 1130AG as well as test with an iphone or ipod when I get the chance; I'd just really like to find out what the heck is going on with these samsung phones.
Current configuration : 13969 bytes
!
! Last configuration change at 10:18:26 MST Sun Dec 23 2012
! NVRAM config last updated at 10:18:26 MST Sun Dec 23 2012
[Code].....
Cisco Wireless :: 1040 APs Work With WCS
Oct 18, 2011Does aps work with Wcs ?? .
View 4 Replies View RelatedLinksys Access Point :: To Work The Wireless Repeater Mode Work With WPA2-AES
Sep 6, 2011Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedCisco Switching/Routing :: 2960S QoS Configuration Not Work
Dec 20, 2012Recently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies View RelatedCisco Switching/Routing :: 2960S QoS Configuration Doesn't Work
Apr 22, 2013my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
Aironet AIR-AP1252G-A-K9 - Wireless Access Point
Mar 19, 2011I just picked up a Cisco Aironet AIR-AP1252G-A-K9 Wireless Access Point to mess around with at home and learn IOS.
The unit didn't come with a power adapter or any accessories. Just the bare AP. Does this AP need a controller to work? Can I use it as a standalone AP?
Cisco :: Configuring Aironet 1100 Access Point?
Dec 22, 2011I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP. I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network. It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't. What IOS command would enable ICMP echo on my access points in this case?
View 8 Replies View RelatedLinksys Access Point :: E3000 Configuration As Access Point?
Apr 6, 2011I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedCisco Wireless :: Aironet 1130AG - Login To Wi-Fi Access Point?
Oct 13, 2010I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies View RelatedCisco :: 1130 - Aironet Access Point Not Able To Connect By User
Jun 12, 2011I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
Cisco Wireless :: Aironet 1310 - Outdoor Access Point
Sep 13, 2012I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
Cisco :: Setting Up Aironet 3500 Series Access Point
Nov 21, 2012links with information / guidelines for the initial setup for this Access Point?
View 7 Replies View RelatedCisco :: Change WPA2 Key On Aironet 1231g Access Point?
Mar 22, 2012I am trying to change wpa2 key on an Aironet 1231g access point. Once I change they key, clients cannot authenticate to the access point unless they either change the password or forget and re add the network on the client device. Is there any way to make the client ask for a new key if the key doesn't match when authenticating?
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 7009 - Syslog Configuration Doesn't Seem To Work For NX-OS
Sep 10, 2012we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
Cisco Wireless :: Aironet 1262N - Access Point Behind Non-Root Bridge?
Apr 9, 2012I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
Cisco Wireless :: 1242AG / Maximum Associations In Aironet Access Point?
Feb 12, 2011I have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
Aironet 1121 - Client Isolation On 1 SSID In Cisco Access Point
Feb 2, 2011i've been looking for a way to isolate clients on a Cisco Aironet 1121 on a certain SSID, and i cant find anything, tried pretty much everything i coudl remember, but since im no expert on Cisco wireless.
Quote:
Cisco IOS Software, C1100 Software (C1100-K9W7-M), Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
[Code].....
Cisco Switching/Routing :: 65535-BGP Distribute List Blocking Routers / Configuration Does Not Work?
Jan 17, 2013Why the below configuration does not work? BGP exchanges routes without a problem all the time the distribute list is removed from the config. When I apply the distribute list it blocks all routes, not just those intended in the prefix list.
[CODE]....