Cisco Wireless :: Aironet 1040 Dual Band Disconnects Mac OS X

Dec 26, 2012

we have several AP1040 in the office, but the latter is a Dual Band 2.4 GHz and 5 GHz. And we have problems with all workstations MAC OS X gets a lot of disconnections during the day, the strangest thing is that the OS X community is aware of the problem, and their only recommendation is to buy the external Aironport has better hardware.

View 3 Replies


ADVERTISEMENT

Cisco WAN :: Wireless Cannot See The 1040 Aironet

Jan 8, 2013

everyone can connect to the 1040 ap except my laptop and another one. for some reason it stopped showing , it was working fine and out of the blue nothing.

View 2 Replies View Related

Cisco Wireless :: Slow Connection With Aironet 1040?

Nov 15, 2012

I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread ([URL]) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
 
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
 
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.

View 9 Replies View Related

Cisco Wireless :: Configuring Aironet 1040 With WPA2-PSK?

May 24, 2012

I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
 
This is what I have so far:
 
Current configuration : 1684 bytes
!
version 12.4
no service pad

[Code].....

View 1 Replies View Related

Cisco Wireless :: How Many Clients Can Be Connected To Aironet 1040 AP

Jan 1, 2013

i have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?

View 3 Replies View Related

Cisco Wireless :: Aironet 1040 IP And Splash Page Redirecting

Mar 11, 2013

I am trying to create a welcome screen for people who join the guest network on my aironet 1040.Webpage pass-through is really what I want but I know that doesn't work on a 1040.What does: IP redirect, Conditional Web redirect or Splashpage redirect?

View 1 Replies View Related

Cisco Wireless :: Aironet 1040 Access Point Managing

May 22, 2012

We are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.

View 5 Replies View Related

Cisco Wireless :: Aironet 1040 How To Configure Access Points

May 21, 2012

I have a Cisco aironet 1040.
 
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?

View 16 Replies View Related

Cisco Wireless :: Setting Up Aironet 1040 Access Point

Mar 13, 2013

I'm working on setting up an Aironet 1040 Wireless Access Point for my company.  It's my first time setting up something like this, and I've run into a bit of trouble.
 
I created my first SSID easily enough, following the manual and guides online.  I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great.  However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
 
I created VLAN 2, and then another SSID which I linked here.  I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager.  I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'.  I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.

View 4 Replies View Related

Linksys Wireless Router :: No Connection To 5GHz Band On E3000 Dual Band?

Apr 14, 2010

I have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.

View 9 Replies View Related

TP-Link Dual-Band Wireless :: DHCP Not Working For 6 GHz Band?

Apr 2, 2013

Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink

I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.

View 1 Replies View Related

Cisco :: Aironet 1040 And Radius Auth Failure?

Sep 24, 2011

I have setup a Cisco Aironet 1040 to connect to our Radius server which I have also configured.
 
I can successfully connect up any Iphone or Ipad but I cannot get any laptop to connect.
 
I have attached the logs showing the Iphone Successfully logging in and the Laptop Failing. Every single failure in the Event log for NPS comes up with
 
Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information.
 
User:
Security ID:            NULL SID
Account Name:            scottd
Account Domain:            AMSLAN

[Code].....

View 12 Replies View Related

Cisco :: Configure Aironet 1040 Access Point?

Oct 27, 2011

I am trying to configure Aironet 1040 access point. After systems get connect they immediately get disconnected. The error observed on the device is as below

%DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 000e.83c8.c88a Reason: Disassociated because sending station is leaving (or has left) BSS
 
and the ssid is not getting broadcasted. kindly let me what could be the cause.
 
[code]....

View 3 Replies View Related

Home Network :: Set Up Access Point Aironet 1040 Cisco?

Nov 23, 2012

how i can set up access point aironet 1040 cisco?

View 2 Replies View Related

Cisco :: Samsung Android Phones Cannot Connect To Aironet 1040 Network

Dec 26, 2012

Every device I've tried to connect to my WiFi network have no issues connecting at all, except for, as far as I can tell, Samsung Android phones. My sample set is very small, but both a Samsung Galaxy S3 (both before and after custom ROM install) and a stock Samsung Galaxy Nexus.
 
I've tried setting a vlan up with no encryption and open authentication, and the phones just halt on "connecting". This issue is both on the 2.4Ghz and 5Ghz Radios.
 
What is working is various computers with both intel and broadcom adapters, a Brother printer, and a Motorola Droid 3 and Motorola Photon Q. I'm starting to think that it's an issue with the radio in the Samsung phones, but the S3 is 5ghz compatible and the Nexus is only 2.4, so they must have different radios. I'm also pretty sure that it's not software on the phones since the S3 had the same problem with stock ROM and CM 10, and the Nexus is Vanilla Google ROM.
 
I'm waiting to get a chance to upgrade to the new FW for my aironet 1040, and I'm going to fire up an old 1130AG as well as test with an iphone or ipod when I get the chance; I'd just really like to find out what the heck is going on with these samsung phones.
 
Current configuration : 13969 bytes
!
! Last configuration change at 10:18:26 MST Sun Dec 23 2012
! NVRAM config last updated at 10:18:26 MST Sun Dec 23 2012

[Code].....

View 15 Replies View Related

Cisco Switching/Routing :: Access Point Aironet 1040 Configuration - Not Getting 802.11n To Work?

Jun 25, 2012

I can't figure out how to get the config right for the 802.11n channel to work.

View 4 Replies View Related

Cisco :: Dual SSID (with Dual VLAN) On AiroNet 1130?

Dec 17, 2012

how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
 
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
 
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
 
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
 
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.

View 2 Replies View Related

Cisco Wireless :: 2602E Run As Non-Dual Band?

May 27, 2013

We had been purchasing the Aironet 1242AG's but found they are discontinued and we should purchase the 2602E Standalone device. I have noticed that all the antennas are dual band and support MIMO. In the past we would just buy a splitter box and connect it to one of the antenna ports on the AP, and then run cables to antennas and connect those to the splitter box. The antennas were just standard 2.4Ghz 3-5 dBi. We would set that one radio on the AP to transmit and receive. Now I am wondering if this whole setup will change on a 2602E because of the MIMO?I have seen there are MIMO antennas and I am trying to figure out what is compatible and what is not. Is my old way of doing this still going to work but we'll only see G speed? And to get N speed do we need the MIMO antennas in place?

View 5 Replies View Related

Cisco Wireless :: Dual Band On AP541

Jul 24, 2011

I just got 3 AP541, the reason for getting this was the dual band , but how to get this AP to actually give both 2.4 and 5 GHZ at the same time?
 
I have in my other office a Asus RT56, it costs about 1/3 of the Cisco and this supports both 5 and 2.4 GHZ and i get a 450 mbit connection, can only get 130 on the Cisco.

View 1 Replies View Related

Cisco Wireless :: WLC 7.4 Dual-Band Radio Section

Apr 9, 2013

Not sure if it's new in WLC 7.4 code, but I now see "Dual-band radio" section everywhere in addition to "802.11a/n" and "802.11b/g/n". My dual band APs (for example 2600's) show up under both 802.11a/n and 802.11b/g/n as in the past. So what is this new category "dual-band radio" for then?

View 3 Replies View Related

Reconnect Netgear DGND3300 Dual Band Wireless - N?

Jan 29, 2011

I purchased the Netgear a couple of years ago and it worked great. Since I've upgraded to a faster bandwith from Verizon, I can't get the Netgear to work. What am I not doing?

View 1 Replies View Related

Using Old Linksys Wireless N Dual Band Router E2500 As AP?

Jul 31, 2011

I just bought a linksys wireless n dual band router e2500 and i want to make my old wrt54g router as an access point. how do i do this and where to start?

View 11 Replies View Related

Linksys Wireless Router :: EA 3500 Dual Band But Only 1 Available

May 17, 2012

I had the store set up my EA3500 which is a dual band...home 1 and home 2. I can only see home 2 which is the smaller band width.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 2.4 Ghz Is Not Working

Dec 31, 2012

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast

I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.

View 14 Replies View Related

TP-Link Dual-Band Wireless :: NFS Is Very Slow With WDR3600?

Feb 18, 2013

Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :

I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?

View 2 Replies View Related

TP-Link Dual-Band Wireless :: WDR7500 No Internet On 5 GHz

Mar 29, 2013

Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast

The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: Does WNR4300 Support With DD-WRT

Nov 15, 2012

Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Newroz Telecom

Can I replace firmawre TP-Link WDR4300 to DD-WRT to use it?, either my TP-link already has VPN,NAT,QOS,..etc like as DD-WRT so does need to replace firmware for better?

Does TP-Link WDR4300 support with DD-wrt? Is it working clearly without any problem?

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 Get GMT Not Working

Jan 6, 2013

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : latest
ISP : Clear

Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.

View 1 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - 2.4 GHz Signal

Mar 28, 2013

Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :

I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?

View 2 Replies View Related

Cisco Wireless :: Access Point 2602e Antennas Dual Band

Apr 9, 2013

I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:

• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
 
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?

View 9 Replies View Related

Cisco Wireless :: WAP321 / Dual Band Concurrent AP With Captive Portal?

Sep 6, 2012

Was looking at purchasing WAP321 however after looking at the spec's I see it has not got concurrent dual band (2.45Ghz/5Ghz) is there any simular access points with dual band and captive portal?

View 2 Replies View Related

TP-Link Dual-Band Wireless :: TL-WR2543ND / USB External HDD Not Recognized

Mar 30, 2013

Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :

ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:

1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.

2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.

3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.

What I can conclude from those tests is that:

1) My External HDD is working normally;

2) The router's USB port is working properly;

3) So, if both are working, it can only be a matter of compatibility between them.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - How To Get Full 450Mbps

Jan 14, 2013

Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet

How do I get the full 450 Mbps out of my router on the status it saying 300Mbps

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved