Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 RepliesIt`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies View RelatedI just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies View RelatedI have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies View RelatedWe have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View Relatedhow to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.
View 4 Replies View RelatedI must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies View RelatedHow do I convert my wireless router to a wireless AP (Access Point)?While connected to the main router go Start then Run in XP - (Windows key plus R in Vista and Windows 7), then type in the following, including all the spaces:- cmd /k ipconfig /all -- then press Enter and from the black form that shows up, take a note of the numeric code beside the word "gateway" -- usually something like 192.168.0.1. Type exit to close the black form.Now connect the router to be converted only to a computer via network cable and log in Setup the wireless security Disable the DHCP and change the LAN IP to match the gateway IP but ending in something like .253 Finally connect one of the four LAN ports of the AP to the main router, do NOT use the WAN port.
View 4 Replies View RelatedI mis-ordered some 3502i’s . They came with Mesh image by accident.
Can I just setup DHCP Option 43 TLV to point to my WLC, plug the AP in and have it change from Mesh to LWAP?
How do I switch from Mesh to LWAP without touching console?
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies View RelatedAIR-SAP1602I is a Standalone AP (Fat-AP), can we convert it to Ctrlr-based AP(Thin-AP) via install another IOS ?!In contrast, can we convert AIR-CAP1602I to be a Standalone AP ?!
View 5 Replies View RelatedThe WES610N bridge seems to work fine, but I cannot get into the web-based setup. I have tried using it directly through my laptop, as the instructions show, then through an Asus RT-53N as a router. I did have the 610 connected to my laptop's ethernet socket, where it provided internet through the Asus RT-53N wireless router just fine, but when I tried to access the setup, again, it would not work. Next, I tried it through a desktop and Linksys RVS4000, again nothing. I would like to check the firmware and see what else is in the menu.
View 6 Replies View RelatedI am running my home network and WAP(WPA2) behind a d-link gaming router (DHCP) with no inbound or outbound restrictions; however, I am unable to access the internet using my ipad unless I put the WAP in the DMZ. Also, if I configure security using the setup program, I can not log on to the web based utility. I have to disable security with the set up program and then log into the utility. BTW..the UID must be left blank to log into the utility( PW only) to configure the WAP, even though the manual says otherwise.
Now after all this, the WAP will be up and running for days even a few weeks. Then for no reason it will no longer be accessible and I will power it down and back up and it works fine. But this will work only a few times and I have to hit the reset button and reconfigure it all over again.
The firmware has been updated and nothing else has issues on the network. This has been happening since i bought it 3yrs ago, using an iPad, iPhone, Laptops, and PCs( XP and Windows 7) but in the past year it has been more frequent.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
Can I connect a WGA54G (v2.1) to a standalone desktop PC running XP Pro SP3 in order to access a wireless router. I'm trying to eleminate wires and I have a spare WGA54G so I hated to buy a wireless card for the PC if I don't need to
View 3 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
The field engineer has a stand alone 24 port 2900 series switch that he has different equipment connected to and are segmented using VLANs. So for example, he's got ports 1-4 assigned to VLAN 10, 5-12 assigned to VLAN 20, 13-19 assigned to VLAN 30 and 20-24 assigned to VLAN 40. He would like all the gear on VLAN 30 to have the ablity to talk to all of the other VLANS, but VLAN 40 should not be allowed to talk with any other VLAN. Trunking would do no good here since the switch isn't connected to anything and you can only assign one VLAN per port.
Is there a way to do this within the stand alone switch? The only possible way I could think of would be to ensure that each VLAN has an assigned IP number (subnet) and doing this through access lists.
Does the access point 1600 and 2600 support flexconnect mode?
View 5 Replies View Relatedhow to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies View RelatedWe setup some new CAPWAP AP 3602E in the network and configure the DHCP server option 43 , but the WLCs still cannot detect the APs , Do you know if there any new way to troubleshooting?
WLC: 5508 version: 7.2.103.0
SW:3750E
AP: AIR-CAP3602E-C-K9
I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 15 Replies View Related