Linksys Access Point :: WES610N Cannot Get Into Web-based Setup
Aug 9, 2012
The WES610N bridge seems to work fine, but I cannot get into the web-based setup. I have tried using it directly through my laptop, as the instructions show, then through an Asus RT-53N as a router. I did have the 610 connected to my laptop's ethernet socket, where it provided internet through the Asus RT-53N wireless router just fine, but when I tried to access the setup, again, it would not work. Next, I tried it through a desktop and Linksys RVS4000, again nothing. I would like to check the firmware and see what else is in the menu.
I have a WES610N in my office connected to a E4200 @ the cable modem in the family room. ~30'.The connection is fine and works well when working.Connected to the WES610N I have:
-Polycom VOIP phone -HP Mediasmart Windows Home Server -Desktop -Multi-Function Laser Printer
I have two issues.
1) The Polycom does a random reboot that I have traced down to it loosing it's IP 2) The Windows Home Server looses it's IP requireing a hard reset.
I have enabled QOS for the polycom and that just worked with managing data. However both devices seem to loose their IP regularly. The desktop might also be having the issue but because it is Vista I suspect Vista is better equipped to deal with IP issues.
I am running my home network and WAP(WPA2) behind a d-link gaming router (DHCP) with no inbound or outbound restrictions; however, I am unable to access the internet using my ipad unless I put the WAP in the DMZ. Also, if I configure security using the setup program, I can not log on to the web based utility. I have to disable security with the set up program and then log into the utility. BTW..the UID must be left blank to log into the utility( PW only) to configure the WAP, even though the manual says otherwise.
Now after all this, the WAP will be up and running for days even a few weeks. Then for no reason it will no longer be accessible and I will power it down and back up and it works fine. But this will work only a few times and I have to hit the reset button and reconfigure it all over again.
The firmware has been updated and nothing else has issues on the network. This has been happening since i bought it 3yrs ago, using an iPad, iPhone, Laptops, and PCs( XP and Windows 7) but in the past year it has been more frequent.
I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
I have a Linksys E1000 wireless router, and I seem to have either written down the password incorrectly or am using the wrong one. Regardless, I can not access the web-based setup for the router. Is there anyway to reset the username and password for it?
I have an EnGenius AP (EOC-2610) I want to connect to my primary router (WRT310N) to extend my network. how I must setup the WRT310N (and maybe the EnGenius) to make it all work together ?
Is the AP's IP should be static ? ie 192.168.1.2 (next to main router's IP)or should it be static in the the primary's DHCP range ? ie 192.168.1.101 or should it be dynamic the IP given by the primary router ?
I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
How do i setup my Linksys E1500 router as an access point? I have a main router upstairs but the signal is weak in the basement. How do i configure this router as an access point for internet?
I've got a WAP610N access point and 4 WET610N to connect to it - however, no matter what I do when trying to install the WAP610N the setup tells me it cannot find the device.I've got the WAP610N connected to a homegateway (SAGEM) and my computer connected wired to the HGW. The HGW is setup as a DHCP server, everything beside the WAP610N works. It gets an IP address, and I can login to the web interface of the access point - but is still unable to use the setup and unable to connect any of the WET610N.
i'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
Can I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
I want to setup Wireless Clients MAC+Active Directory based acess on AP 1242 standalone Wireless series.Steps i have configured :
1) SSID manger under Open authentication : Selected with EAP. 2) under advacned Radius.MAC Address AuthenticationMAC Addresses Authenticated by: Authentication Server Only 3) Server Manger : Current server list added the radius ip address 10.1.200.x
I need a router that can receive the signal from my Verizon 4G Jetpack so that I can send signal to items that require cat5 cable.Can the WES610N do that or is there one that can?
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
I am trying to set up my 3Com wireless Access Point that was given to me. I have searched for software to set it up but can't find any.I have read somehwre that the software doesn't even work on Windows 7 anyway.know the default ip adress of this router or how to get into the config pages to set it up.
I need to setup my laptop for two different wireless configurations,at home i have a wireless network that work fine, however, at work i need to configure TCP/IPv4 by feeding in the required IP, Subnet Mask, Gateway etc. But i have to repeat this everyday in office and at home by removing and feeding in the parameters. Is there anyway that i can have both configurations and the system just automatically finds the right wireless network without changing the parameters. I am using windows 7.
I bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
