I have an EnGenius AP (EOC-2610) I want to connect to my primary router (WRT310N) to extend my network. how I must setup the WRT310N (and maybe the EnGenius) to make it all work together ?
Is the AP's IP should be static ? ie 192.168.1.2 (next to main router's IP)or should it be static in the the primary's DHCP range ? ie 192.168.1.101 or should it be dynamic the IP given by the primary router ?
I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 by an ethernet cable if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible
View 5 Replies View RelatedMy internet provider is telus and they gave me a modem/router combo model VA-G3810bn/tl and another router a linksys wrt310n and i want to by pass the router built into the modem so my linksys will put out a signal instead as it is faster connection any im using windows seven and mozilla firefox if that matters
View 1 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View RelatedI am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedCan I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?
View 1 Replies View RelatedThe WES610N bridge seems to work fine, but I cannot get into the web-based setup. I have tried using it directly through my laptop, as the instructions show, then through an Asus RT-53N as a router. I did have the 610 connected to my laptop's ethernet socket, where it provided internet through the Asus RT-53N wireless router just fine, but when I tried to access the setup, again, it would not work. Next, I tried it through a desktop and Linksys RVS4000, again nothing. I would like to check the firmware and see what else is in the menu.
View 6 Replies View RelatedI have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedHow to setup WRT54G in router mode
View 9 Replies View RelatedI have WRT54GL and want to setup wap54g as wireless repeater? I need to expand the signal using wap54g
View 1 Replies View Relatedwap54g setup wizard 3.0 download
View 1 Replies View RelatedHow do i setup my Linksys E1500 router as an access point? I have a main router upstairs but the signal is weak in the basement. How do i configure this router as an access point for internet?
View 2 Replies View RelatedI've got a WAP610N access point and 4 WET610N to connect to it - however, no matter what I do when trying to install the WAP610N the setup tells me it cannot find the device.I've got the WAP610N connected to a homegateway (SAGEM) and my computer connected wired to the HGW. The HGW is setup as a DHCP server, everything beside the WAP610N works. It gets an IP address, and I can login to the web interface of the access point - but is still unable to use the setup and unable to connect any of the WET610N.
View 2 Replies View Relatedi'm facing a big problem with my access point WAG54G ver 2.0 ,i just bought it from 2 days but i find alot of problems when i start using it ,i have read all the user guide and the quick install to see how to setup the access point and make it work with my adsl.i have configured all things right using PPPOE and putting my user name and password and then save settings then go to the status and press on connect , but it don't connect with me just i find connecting and adsl link : Down and still making connecting and nothing after that and my adsl led is off haven't any colors ,and when i get again to basic setup i found the password that i put it in the ppoe login is too long , not my password i tried to see what is this password and recover the hidden i found it " d6nw5vlx2pc7st9m ".i don't know what is the problem i tried alot of times to change setting and also the same problem.i think that it's a frim ware problem and i tried install a new updated frimware but everytime trying to install it get installing and suddenly stoped and white page appeard and all the access point is stopping and when restart it the ac power.
View 3 Replies View RelatedI have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies View Relatedhow do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address.
View 2 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
My WRT310N linksys wireless router has recently stopped permitting internet access to devices connected to it, both wired and wirelessly. I have connected my broadband modem directly to a single computer (which is how I am posting this) and evidently there is nothing wrong with my internet service. I have tried restarting my modem, the router, and the computers I am trying to access the internet with, and it has not worked. Note that local communications work fine, I was able to ping another device connected to the router, and even establish a TCP connection.It is possible that the settings on the router have been changed without my knowledge, if so, however, I do not know which setting could be causing this.
View 1 Replies View RelatedI have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I am trying to set up my 3Com wireless Access Point that was given to me. I have searched for software to set it up but can't find any.I have read somehwre that the software doesn't even work on Windows 7 anyway.know the default ip adress of this router or how to get into the config pages to set it up.
View 19 Replies View RelatedI need to setup my laptop for two different wireless configurations,at home i have a wireless network that work fine, however, at work i need to configure TCP/IPv4 by feeding in the required IP, Subnet Mask, Gateway etc. But i have to repeat this everyday in office and at home by removing and feeding in the parameters. Is there anyway that i can have both configurations and the system just automatically finds the right wireless network without changing the parameters. I am using windows 7.
View 4 Replies View RelatedI bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]
View 5 Replies View RelatedSetup Buffalo WHR-HP-G54 as wireless access point?
View 1 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View Related
