Linksys Wireless Router :: Using WRT310N As Access Point To Extend Network

Sep 5, 2011

I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: Can't Set Default Gateway On WRT310N In Access Point

Jul 28, 2011

I am using a WRT310N.  I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N.  So I just plug the LAN port on the WRT310N directly to my LAN switch.  I just need the WRT310N to have an IP address for management.  So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN.  You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.

View 1 Replies View Related

Linksys Wrt310n - Setting Up Second Router As Access Point

May 26, 2011

My internet provider is telus and they gave me a modem/router combo model VA-G3810bn/tl and another router a linksys wrt310n and i want to by pass the router built into the modem so my linksys will put out a signal instead as it is faster connection any im using windows seven and mozilla firefox if that matters

View 1 Replies View Related

Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?

Aug 17, 2011

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
 
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?

View 1 Replies View Related

Linksys Wireless Router :: Use WRT54G Router With The Newer WRT310N To Extend Signal?

Aug 27, 2008

Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?

View 7 Replies View Related

Using A Linksys WRT310N As An Access Point?

Sep 5, 2011

I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 by an ethernet cable if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible

View 5 Replies View Related

Linksys Access Point :: Using Wireless G WAP54G To Extend Coverage?

Jan 29, 2012

I have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?

View 1 Replies View Related

Linksys Access Point :: How To Setup AP To WRT310N

Aug 31, 2009

I have an EnGenius AP (EOC-2610) I want to connect to my primary router (WRT310N) to extend my network. how I must setup the WRT310N (and maybe the EnGenius) to make it all work together ?
 
Is the AP's IP should be static ? ie 192.168.1.2 (next to main router's IP)or should it be static in the the primary's DHCP range ? ie 192.168.1.101 or should it be dynamic the IP given by the primary router ?

View 3 Replies View Related

Linksys Access Point :: Extend Cable On Outside Antenna On Wap54g?

Jan 30, 2012

I have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?

View 1 Replies View Related

Cisco Wireless :: Extend Signal For RV220W As Access Point?

Mar 25, 2012

I plan to extend the wireless signal for RV220W as a wireless access points now. Can we use lower end model instead of another RV220W?

View 2 Replies View Related

Linksys Wireless Router :: Unable To Access WRT310N Through Browser

Feb 9, 2009

I am unable to access my router through the ip address (192.168.1.1) even though I have verified that is the address. To be sure, I did an ipconfig release/renew, but no results. I want to limit a user's network access by MAC address and I don't think I can do that without accessing the router thru the ip address. 

View 2 Replies View Related

Linksys Wireless Router :: WRT310N Stopped Permitting Internet Access To Device

Aug 19, 2011

My WRT310N linksys wireless router has recently stopped permitting internet access to devices connected to it, both wired and wirelessly. I have connected my broadband modem directly to a single computer (which is how I am posting this) and evidently there is nothing wrong with my internet service. I have tried restarting my modem, the router, and the computers I am trying to access the internet with, and it has not worked. Note that local communications work fine, I was able to ping another device connected to the router, and even establish a TCP connection.It is possible that the settings on the router have been changed without my knowledge, if so, however, I do not know which setting could be causing this.

View 1 Replies View Related

Linksys Wireless Router :: Wrt310n Takes Very Long To Connect To Network?

Sep 28, 2012

When I boot my system lately I have to fiddle with task manager to get things stable enough to connect to my network. This is getting very tiresome. I always find OdHost.exe taking almost all the CPU and have to kill it to get things running. This can't be normal and has not been until recently. I don't know of anything that has been installed in the last several months that is network related.

View 1 Replies View Related

Linksys Wireless Router :: E2500 As Access Point In Office Network?

May 2, 2012

I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?

View 8 Replies View Related

Linksys Wireless Router :: WRT400N - Adding Access Point To Existing Network

Oct 26, 2010

I have an existing wireless network using a Cisco/Linksys WRT400N wireless router (which in turn is connected to a cable internet provider). I need to extend my wireless coverage and so purchased a Cisco/Linksys E1000 to act as an additional access point.  Purchased from BB, the local 'geek squad' rep instructed me to follow the users guide for the set up. After login into the admin service on my E1000, I followed the 'Advanced Routing' instructions and disabled the 'NAT' option and subsequently enabled the 'Dynamic Routing (RIP)' option.  Everything worked like a charm to this point, but now I'm stuck. What steps do I need to follow to allow clients to log onto my wirelss network via the E1000 (secondary access point)? I've established WEP security keys on the WRT400N (primary access point) and want to use the same network security parameters on the E1000.

View 9 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Linksys Wireless Router :: E2500 - Extend Network SSID?

Jan 25, 2012

I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet

View 1 Replies View Related

Linksys Wireless Router :: WAP610N To Extend Network Instead Of Broadcasting Another

Jun 30, 2011

How do you have the WAP610N and WRT610N using the same SSID? I would prefer to have my WAP610N simply just extend my network instead of broadcasting another.

View 1 Replies View Related

Using Repeater To Extend Signal Of Access Point Both TP-Link TL-WA901ND?

Jan 9, 2012

Im in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?

View 1 Replies View Related

Linksys Wireless Router :: WRT610N Way To Repeat 5GHz Network To Extend Range

Dec 27, 2010

I have the WRT610N, and I was wondering if there is a way to repeat the 5GHz network to extend the range.I am trying to stream content from a Blu-Ray player, and while the 2.4GHz network reaches, the signal is very weak.  The 5GHz network doesn't reach, but I would prefer to stream content through that network than the 2.4GHz.

View 7 Replies View Related

Linksys Wireless Router :: Booster For Cisco 3800HGV-B To Extend Network Range?

Aug 15, 2012

I would like to know what to buy to extend the range of my wireless network , which will not reach throughout my house.  
 
Also, I would like to know what the button is for on the front of of the router, since it is not a WPS button, according to ATT.  

View 4 Replies View Related

Linksys Wireless Router :: Extend E4200 V2 Wifi Network With Airport Extreme

Jan 25, 2012

I have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2? Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?I can't stand the interface. The E4200v2 is brand new.

View 1 Replies View Related

Linksys Wireless Router :: Configure Apple Airport Express To Extend Wrt120N Network

Aug 6, 2011

Is it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how? 

View 2 Replies View Related

Linksys Wireless Router :: WRT120N / E1200 - Extend Home Network With Both Wired And Wireless Connections

Jan 27, 2013

I am trying to extend my home network into my basement with both wired and wireless connections.  I have a WRT120N upstairs, which is connected to my cable modem.  I have an E1200 in the basement, which I have connected with a LAN port.  DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet.  They are getting an IP address from the upstairs router, but can't get past the gateway. 

View 1 Replies View Related

Home Network :: WRT310N Linksys Router - Exceptionally High Pings

Jul 14, 2011

Using a WRT310N Linksys Router and just today at 2PM I received the largest and longest lag spike ever, it is still going on as I write this (10:00PM). I am receiving pings of 500+ ping and my download speed spikes like crazy. Here are my speedtest.net results.Here are my results from Netalyzr URL

View 4 Replies View Related

Using LinkSys Router As Switch To Extend Network?

Oct 20, 2011

I have a new Siemens router and have set up my old LinkSys router as a switch (set DNS outside the IP range of the primary router, disabled DHCP server, connect LAN to LAN port).The SSIDs are still different. As a result each device now sees 2 networks and although internet GW is available from either connection, not al resources are shared across the network. There is one driveshare (with wired connection to the secondary switch) which cannot be seen by some of the wireless resources on the same secondary network.Questions:1. How can I set up the NW config such that it is seen and behaves like one physical network, anbd roaming devices pick up the signal from the strongest access point?

View 3 Replies View Related

Linksys WRT54G Setup As Access Point On Wireless Network?

Jun 28, 2011

I have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.

View 2 Replies View Related

Linksys Access Point :: EA4500 Need To Improve Home Wireless Network

Jun 6, 2012

I am trying to improve the coverage of my home network.I have Fios, and with the existing Wireless capabilities, there are several dead and low coverage areas in my house.  This is due to a combination of where my router is (Limited by input feed) and the confuration of the house.
 
I have CAT-5 running to most rooms, so adding wired devices is not an issue.  I went out and picked up an EA4500 router, and my plan was to convert my Fios Router to a bridge and use the EA4500 as the DHCP server.  However, even with this router, my coverage is not improved.  My preferred solution will be to get 1 or 2 additional access points that I can plug into my wired network, however, I would want to have a common SSID for the entire network.

View 8 Replies View Related

Linksys Access Point :: WAP54G - Can't See Wired Network Devices With Wireless Connection

Mar 3, 2011

I work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.

View 2 Replies View Related

Linksys Access Point :: Connecting To Network That Is TKIP Secured With WMP11 Wireless PC Card

Nov 8, 2006

,I was having problems connecting to a network that is TKIP secured with a WMP11 Wireless PC card. I'm wondering if this is possible.

View 9 Replies View Related

Linksys Wireless Router :: How To Configure WRT310N

Dec 6, 2012

How to connect my att dsl westell moden to my Linksys router.  I am changing service providers from comcast to att.  My router was working with my cable model but I'm unable to configure it to communicate with the dsl modem. 

View 9 Replies View Related

Wireless-N Gigabit Router (WRT310N) / Cannot Complete The Network Setup Wizard

Oct 2, 2011

I have two PCs connected to each other through a Wireless-N Gigabit Router (WRT310N). One PC is running Windws XP while the other is running Windows 7. At this point I do not have, or want, Internet connectivity. I would, however, like to call web pages on the Windows 7 PC from the Windows XP PC. The Windows 7 PC has php files that run C++ files to analyze files supplied by the Windows XP PC and I would like to send the results of the analysis back to the XP PC.The reason for this is that I am setting up a home based web site that allows users to run programs on my Windows 7 PC but I want to keep hackers from accessing files on my Windows 7 PC. So the XP will be connected directly to the Internet and the Windows 7 PC will only be connected to the XP PC.I can successfully ping both ways between the Windows 7 PC and XP PC. So I fire up FireFox (FF) on the XP PC and type the following in the FF URL box.

[code]....

The same happens when I replace the Windows 7 PC IP address with the Windows 7 PC name.I tried to set up a network between the two PCs with the MS network wizard on the XP box. It made a setup disk with a single file on it. I was supposed to run the setup file on the other PCs that are supposed to be on the network but, whe I did, I got the following message.Cannot complete the Network Setup Wizard,An error occurred during the configuration of the network on this computer.You can configure the network manually.

View 3 Replies View Related

Linksys Wireless Router :: WRT310N - Color Of Internet LED?

Feb 5, 2012

I am getting 22-30mbs down through my router wired and I'm only getting about half of that through wireless.  Is this normal?  I also have a question about the color of the internet led.  The online manual says that it should be blue, but mine is green.  All of the other LEDs are blue except the internet one.  Not sure if that is an issue or not.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved