Cisco Wireless :: Extend Signal For RV220W As Access Point?
Mar 25, 2012I plan to extend the wireless signal for RV220W as a wireless access points now. Can we use lower end model instead of another RV220W?
View 2 Replies
ADVERTISEMENT
Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?
Aug 17, 2011how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
Using Repeater To Extend Signal Of Access Point Both TP-Link TL-WA901ND?
Jan 9, 2012Im in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?
View 1 Replies View RelatedPossible To Extend Wireless Signal Without Making New Access Points
Jan 18, 2012At the moment i have 3 routers across the house, each acting as a wifi access point.My problem comes to when i use my phone or laptop, it connect to a random access point doesn't matter of the signal.Is it possible to combine 3 routers as one access point. So that i would connect to one access instead of 1of 3 access points, that would be a strong wifi signal no matter when i am in the house. Something similar to what bit malls or stores have.I have looked at wi-fi repeaters, but they just repeat the wifi and make new access point.
View 2 Replies View RelatedLinksys Access Point :: Using Wireless G WAP54G To Extend Coverage?
Jan 29, 2012I have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
View 1 Replies View RelatedLinksys Wireless Router :: Using WRT310N As Access Point To Extend Network
Sep 5, 2011I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View RelatedCisco Wireless :: Setup RV220W As Access Point?
Nov 10, 2011May I know that can a CISCO RV220W setup as a Access Point in company network? We already have a router for IP management. is it possible to setup as Acces point?
Also can we separate the guest and internal user for using wireless by difference SSID and VLAN. It seem it cannot setup if i need to setup limited network access right by SSID and VLAN.
Cisco Wireless :: Using WAP321 To Extend RV220W Wi-Fi Network?
Feb 27, 2013I'm trying to configure a WAP321 so that I have the same SSID and WPA2 password on both the RV220W and the WAP321 so that i can reach all areas of my clients location.
View 1 Replies View RelatedLinksys Access Point :: Extend Cable On Outside Antenna On Wap54g?
Jan 30, 2012I have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedCisco Wireless :: 1142 Access Point Signal Pulsing
Aug 1, 2012I've recently set up a guest wireless in my office, using a WLC 2504 controlling 4 1142 APs. They have been working great for about a month, but as of yesterday, the Wifi signal from 2 of the APs began to pulse - 5 seconds on, 1 second off - which makes it unusable. [code]
All APs are receiving PoE from their last 3750 (at default levels). I've cycled the individual APs, as well as the WLC, but the issue remains.Except for the initial 3750 directly connected, all other 3750's are different.
Linksys Access Point :: WAP610N Wireless-N Repeating Signal
Sep 14, 2011Is it possible to use WAP610N Wireless-N Access Point repeating signal with another WAP610N Wireless-N Access Point?what the range of signal when using a single WAP610N Wireless-N Access Point ?How many devices can connect to WAP610N in the same time?
View 1 Replies View RelatedTL-WR740N How To Extend Wireless Signal
Jan 21, 2013Ground floor: My ISP's wireless router and an 8-port switch. For wireless communication I use the ISP's Wifi and the 8-port switch is used for wired rj45 sockets around the house.
1st Floor: I have a TP-LINK TL-WR740N Wireless Lite N Router 150 MBps which I connected to a socket and have a PC connect with wire on it and also used for Wifi. The Wifi network I setup on the 1st floor is different than the one on the ground floor (2 routers).
At the first floor I have the problem that in other bedrooms far from the router the Wifi signal (either gets lost) or it's very low. So I bought a TP-LINK TL-WA701ND Wireless N Access Point 150MBps which I configured as universal repeater.
The access point supports only WEP encryption when used as repeater/universal repeater so I changed the wifi of the router to WEP with ASCII with 128bit character length and established the connection.The most important now is that even though the Wifi signal in the bedroom with the AP is full, when I switch off the wifi of the iPad and back on, it is not connecting to the internet. Yesterday I noticed that it was giving me the ethernet card IP (169.…). I went close to the router with the iPhone, got connected and when came back to the room with the AP it was working but the iPad is not working.
Access Point Or Wifi Signal Booster / D-link Wireless N Gigabit Router
Jan 2, 2013Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies View RelatedExtend Wireless Signal / Range Of Internet?
Dec 7, 2012how do i extend wireless range and increase signal to granny flat for internet? from the modem to the granny flat about 15m+, i tested it with my laptop get 3 green signal and on inSSID get around 74+ RSSI but with Asus-n13 and mini Tp Link wireless USB adapter get above 79-80 RSSI. don't know why but i get signal for surfing internet on laptop but randomly get drop out. household gave me $200 to improve the signal....
View 4 Replies View RelatedLinksys Wireless Router :: Connecting Two WRT54G2 To Extend Signal
Jan 27, 2013I have available two Linksys Wireless-G Broadband routers (WRT54G2) which were given to me by a family member. We have been using one of the routers by itself for quite some time, but do not have adequate signal throughout our home. I decided it would be easier to design the floor plan of the house for you to see its location in relation to the rest of the house regarding walls and what not. We have HughesNet Satellite internet which is located on the roof just about the location of the modem and router in the bottom right of image.
What do you think would be the best location of the main router? I have read it would be best centrally located since the signal travels horizontally and vertically. I just purchased a 100' Ethernet cable since the only one we had was what the HughesNet installer provided us with which is about 4'. I was originally thinking I would route the cable from the main router to the basement where the second router would be placed since the signal down there is about 1 out of 3 bars on my iPhone. The signal upstairs in the main room (room in top middle of image) ranges from 3-5 out of 5 bars on my laptop.
I just wanted to place a post sooner rather than later to see what your opinions were on the location of the main router and what I have in order to increase the signal.
Linksys Wireless Router :: WRT120N - Extend Signal Through Ethernet Cable?
Nov 11, 2012I have a Linksys WRT120N plugged directly into my cable modem upstairs, an 8 port switch plugged into it, an ethernet cable from it run downstairs in my house to another 8 port switch and a Linksys E4200 plugged into it. I want both routers to allow me to connect to the internet wirelessly if possible. I cannot even access the E4200 from a browser, because the IP adress 192.168.1.1 goes directly to the WRT120N.
View 4 Replies View RelatedD-Link DIR-825 :: Getting Access Point And Signal Strength?
Nov 21, 2011I have connected my DIR-825 to my cable modem through the network ports and completed the configuration. Everything works fine, I am able to connect through wireless to the DIR-825 and access the internet. I had to do this as my cable modem is also wireless and does not allow another router to be connected through the internet connection, but I want to get a better signal stength than the cable modem.When I am not wireless connected, I can see the two bands at full strength in the view available wireless networks screen. As soon as I connect to either the 2.4 channel or the 5 channel, the signal strenth of the channel I'm connected to drops to horrible, while the non-connected one still shows at full strength.i tried disabling one of the channels, but as soon as I connect to the other, that channels signal strength still drops to horrible.
View 1 Replies View RelatedLinksys Access Point :: Best Way To Expand Signal WAP610N
Aug 22, 2011I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal.
View 3 Replies View RelatedLinksys Access Point :: WET610N Range And Signal Strength?
Nov 9, 2011I'm trying to use the WET610N as a sort of access point/range extender for a single device, a remote monitoring system installed in a barn. It records temperature, power use, etc, and reports it to the internet. The barn is about 250 feet from the house where the wireless router is installed. There will be very little data flowing over the link.Setup on the WET610N went fine, and it saw the remote router at 10% strength and connected to it fine. However, when I attempt to get Status, the screen shows the headings on the left and no data on the right. Attempting to access the internet through the link on my MacBook Pro failed.
View 6 Replies View RelatedLinksys Access Point :: Amplifying WRT160N Signal With Secondary AP
Mar 13, 2012My Linksys Wireless-N router/access point (WRT160NV2) is connected to the internet in my primary residence, delivering 35mbps. I purchased a commercial Engenius product (EAP9550) to amplify the wifi signal over to a secondary house (about 180 ft away, traveling through 3 walls). Configured as an access point, the EAP9550 received and showed signal, but there was zero connectivity. The tech support at Engenius has advised me to configure the EAP9550 as an access point. My linksys router continues to deliver wireless signal for its range, but is only showing (not giving) full connectivity to the secondary access point.
View 1 Replies View RelatedLinksys Access Point :: Increase Signal Strength And Range Of WAP54G?
Jan 19, 2009I have a WAP54G and the signal strength and range is not that great; unit manufactured in 04/2007. I have firmware version 3.04 dated Oct 31, 2005. Customer support is suggesting I upgrade the firmware to 3.04.03 but I am sure it will really do anything to the signal strength and range. Also, they suggested I download new drivers for my desktop wireless card.
View 9 Replies View RelatedHow To Extend Wifi Signal From Neighbor
Aug 9, 2011My friend has an internet connection and Wifi, it reaches my room but with poor signal, is there any way I can strengthen up the signal?
View 1 Replies View RelatedBest Solution To Extend Signal Of Tplink TL-WR10
Feb 14, 2013which will can extend the signal strength? changing antennas, put a wireless amplifier or buy ASUS 66U??change TPLink TL-WR1043ND to ASUS 66U ??? ASUS 66U is best to TPLink TL-WR1043ND and can extend the signal strength by up to twice the distance?
View 1 Replies View RelatedWirelessly Use Second Router To Extend Home Signal Range
Jul 23, 2012I have a BT home hub 2.0A (BT is our ISP) it covers most of our house except for my bedroom. I have two spare routers i'm not using, one is a Speedtouch ST585 v6 and the other is a Belkin F5D7632-4 and was wondering if I could use these to extend the range of the home hub wirelessly. As far as I can tell I cannot install dd-wrt on any of these 3.
View 2 Replies View RelatedHow To Extend Signal Strength - Network Printer Setup
Jul 31, 2012I just got a new-to-me multifunction printer that's "network ready" (ie, has an ethernet cable port.) I also got myself an asus wl-520gu router. For now the router has the factory installed firmware on it, but i could put tomato or ddwrt on it. also in my house I have a linksys router already set up with a WEP encrypted wireless SSID which me and my 5 roommates share. I guess for the purpose of this post we can call that network "Kermit" and pretend it has password "ilovepiggy" This router sits on the second floor landing in our three story house. My printer and this asus is going to be in my room, which is on the first floor. I'd like to
a) get better signal strength/speed in my room
b) network my printer so that I and others can print to it / scan from it wirelessly over the network. Can I do both things? and what would that setup be like? Would it mean making the ASUS a wireless repeater? at what point in the process and how do I add the printer?
Linksys Wireless Router :: Use WRT54G Router With The Newer WRT310N To Extend Signal?
Aug 27, 2008Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies View RelatedCisco Routers :: Setting Up WAP4410N As Repeater To Extend Signal Of E2500?
Apr 18, 2012Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedBelkin Routers :: Cannot Extend Signal With N300 Dual Ban Wifi Range Extender
Feb 10, 2013I am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.