Using Repeater To Extend Signal Of Access Point Both TP-Link TL-WA901ND?
Jan 9, 2012
Im in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1 Processor Count: 1 RAM: 479 Mb Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB; Motherboard: , KM266-8235 Antivirus: None
Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
I am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
I have connected my DIR-825 to my cable modem through the network ports and completed the configuration. Everything works fine, I am able to connect through wireless to the DIR-825 and access the internet. I had to do this as my cable modem is also wireless and does not allow another router to be connected through the internet connection, but I want to get a better signal stength than the cable modem.When I am not wireless connected, I can see the two bands at full strength in the view available wireless networks screen. As soon as I connect to either the 2.4 channel or the 5 channel, the signal strenth of the channel I'm connected to drops to horrible, while the non-connected one still shows at full strength.i tried disabling one of the channels, but as soon as I connect to the other, that channels signal strength still drops to horrible.
Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
At the moment i have 3 routers across the house, each acting as a wifi access point.My problem comes to when i use my phone or laptop, it connect to a random access point doesn't matter of the signal.Is it possible to combine 3 routers as one access point. So that i would connect to one access instead of 1of 3 access points, that would be a strong wifi signal no matter when i am in the house. Something similar to what bit malls or stores have.I have looked at wi-fi repeaters, but they just repeat the wifi and make new access point.
I have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
I have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
I currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
Region : UnitedStates Model : TL-WR702N Hardware Version : V1 Firmware Version : 4.18.107 Build 121123 Rel.31456n ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
I have a fairly large home (>5000 sq ft) with multiple levels and some "dead spots" in the extreme areas. I would like to have a fantastic wi-fi signal through the home for access to my home network for my family and internet for guests. I have Fios with a 50/20 mpm with a "g" router. I also have purchased 2 repeaters (ampedwireless.com) and installed 1. Recognizing that it appears to have created a different network, so this isn't what I want to do. Then I went back and purchased 2 access points. I need to have an "hardware solution" in my theater (basement) as well as in my bedroom (3rd floor).
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2 Firmware Build: 3.12.16 Build 120224 Rel.61005n Wireless Mode: Access point Channel: Auto Mode: 11bgn mixed Channel Width: 20/40MHz Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
I have a WAP54G as my access point, currently it is connected with my BEFSR81 router. I am thinking of changing the access point to a WAP610N for the house. I know that this would work but I was wondering if the WAP54G could be used as a repeater for the outside (I know a lower speed). I know they are two different channels but I wanted a larger range for my wireless. I am on Windows XP, SP2, using Firefox. Can this be done?
I want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?
I need to extend the wireless range over what I have using an E2000. Can I use a WAP610N in repeater mode? If not can I use a WAP54G knowing that there will be a performance loss? Is there another option to add additional coverage to the existing wireless network?
Region : Germany Model : TD-W8961ND Hardware Version : V2 Firmware Version : ISP :
I need to set up an Internal and Guest WLAN. Out of security reason I'd like to separate both networks with VLAN's. Therefore I bought this Router TD-W8961ND and this Access Point TL-WA901ND.
SSID1 = AP1 -> VID 1 (Internal network) SSID2 = AP2 -> VID 2 (Guest network)
How do i need to set up the router that both networks can use the Internet, but only AP1 can see the other internal computers?
We just got a new replacement router at our home. We had a 2wire 2701 HG-S (we got this for free when we signed up for our DSL service) and now replaced it with a Netgear N300 Work and Play model. I want to know if we can set up the 2wire router as another access point to improve our wireless signal range. Right now we have a good signal upstairs (where the Netgear router is located), but not the best signal downstairs. I am able to run an Ethernet cord from the Netgear router downstairs to the 2wire if necessary, if it will improve our WiFi signal. Both of these routers are router/modem combos that include the DSL modem, in addition to wireless access point btw. Is this even possible to do? Would it require me to install a custom firmware onto the 2wire router?
I have a Sitecom WLR 4000 wireless router. I also have a Linksys Wireless G Accespoint. Can I use that AP as a extender/repeater for the Sitecom router? If yes, how to configure one and other?
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
We have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
I have a WAP54g set up as a repeater. It even shows in the WRT54g device list (Tomato firmware) as a WDS interface but nothing can connect to it. I have the repeater's MAC address in the AP and it's set to "Access Point + WDS" mode. I don't know what I could be doing wrong. Is it a conflict of DHCP on the AP vs static on the repeater?
I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
im just want to ask a favor if you can guide me to set up or configure a router repeater to extend my wifi at my home. i dont have a specific brand of repeater yet.. im planning to buy but i have no idea how to set up a repeater by myself.
I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
