I have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
View 1 RepliesI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.
View 5 Replies View RelatedI bought two E4200s with the intent of using the second as a wireless access point to maximize coverage throughout my house. I just learned the hard way that the E4200 doesn't support that feature, and will only act as an access point if physically connected to the primary router that is connected to the internet.
Before I spend even more money on equipment, I was wondering if any of the experts here can tell me whether I can use a Linksys Bridge, like the WET610N or WES610N, to operate the second router in bridge mode and turn it into a wireless access point?
I have never setup an wireless access point before and am having some issues. I have a Linksys WAP54G ver 3.1. A friend gave it to me and he said it was working when he pulled it out of his office.I defaulted the device and using the wizard have the following setup:
Setup:
Network:
Device Name - Linksys WAP54G
Configuration Type - Static IP
IP Address: 10.0.0.239
Subnet Mask: 255.255.255.0
[code]....
When I try to connect to it via my laptop I get the error: "Windows was unable to connect to XXXXX"
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I have 2 story house and trying t extend wireless coverage in the house. I have have 2 routers. One is just wrt54g while the second dual mode EA-4500. Cable modem is located in the basement so i would like to have one of the routers connected to it and use another router as bridge. So which router would be best to use a bridge. If i use ea4500 as a bridge then i would lose dual band features of it.
View 9 Replies View RelatedHaving some problems connecting up my "new" AP My current set-up consists of a Netgear "Virgin Superhub" cable modem/wireless router, a ZyXEL WRE2205 (repeater) in the hall on the first floor, and Ethernet connections through to a number of rooms, including the loft. I can't get wireless access in the loft, and I want to put the AP up there, connected through Ethernet. I want to use the same SSID and security for the AP as on the router and repeater so I can roam around(!) That's possible isn't it?What I've done so far (which hasn't worked) is connected via laptop to AP, set AP into AP mode(!), set the AP to dynamic IP, set the SSID / security the same as the router/repeater, plugged the AP into the Ethernet and tried to connect.
View 7 Replies View RelatedI'm trying to share my existing wireless connection over a WAP54G with the latest firmware, on Windows 7 on a laptop. Basically, the laptop is getting a wireless connection from my Sprint Card, but I need to share a wi-fi connection with an iPod I'll be using to validate tickets. Unfortunately, there is no option to share the wireless connection when I click on the Properties for the connection. When I put in my WiFi settings, the iPod is able to login to the AP, but it cannot obtain an IP. It keeps doing this. Same thing happens with my Samsung Epic which runs Android. I can access the AP manager, and can configure it. Have tried using no security, but still no dice. Even turned off the firewall.
I can surf the internet on the laptop, but I simply can't share the connection with the AP. This is really important as I'm trying to get it setup by next weekend!
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies View RelatedWhat is the maximum number concurrent wireless connections that a WAP54g v3 can have?
View 9 Replies View RelatedI have scoured your website and the web.I do not have the CD rom that came with my WAP54G wireless access point (misplaced) and now need to configure the WAP54G, but for the life of me, i cannot find the link to download client software to configure it anywhere.Could the network admin please post the link on your website to download it, or could they send me a private email with a link, so that i can download, then install it, so that i can use the wireless access Point?
View 6 Replies View RelatedI work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
View 2 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View Relatedhow do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
At one of our offices, we have a Cisco ASA5505 firewall that has dhcp enabled. I have a WRT54G router plugged into that firewall with DHCP enabled. The scope of our inside network is 192.168.51.***, however when connected to the WRT54G, it gives you the scope of 192.168.1.***We have an antenna amplifier screwed into one of the antenna ports on the router. This whole setup works fine.
The problem is we need to install an access point WAP54G in a building across the property (picks up router wireless signal fine) to repeat the wireless signal to the back of the property where the router will not reach. I have read that all you need to do is type in the wireless mac address of the routher into the access point and select "Wireless Repeater". I have the channels set to 6 on both devices as well as the same security configuration. When I try to connect to the wireless network on the access point, It never gives me an ip in the 192.168.1.*** scope, which the WRT54G is configured to give out. Also, in this setup does the WRT54G need to be set to router or gateway mode? I do not need it to distribute ip addresses. [code]
how to set up a WAP54G v3.1 Access Point if you've misplaced the CD?
View 5 Replies View RelatedMy Linksys Range Extender died. So I bought a WAP54G thinking that I could use it as a repeater to extent the range of the signal from my router to the other wireless PCs in the house.
1st floor:
PC1 connected to a WRT54G v.5 router
PC2 connected to PC1 router via USB network adapter
Laptop connected to PC1 royter via internal wireless
2nd floor
PC3 connected to PC1 router via USB network adapter
PC4 connected to PC1 router via USB network adapter
The main goal is to set up the WAP54G in between PC1 and the other PCs to extent the range of the signal particularly to the 2nd floor PCs.The instructions for configuring the WAP54G are fairly straightforward, but the first issue I run into is not being able to connect to the WAP54G web setup. I am using the following instructions:
[url]...
once I configure or setup the WAP54G through another PC as a repeater, will I be able to disconnect it from the PC and use it as a standalone (e.g., plugging only the power in and leaving it in my kitchen or a hallway) to extend the range of the signal? Or does it have to stay connected to PC1 and does PC1 always have to be on for this WAP54G to act as a repeater?
My WAP54G no longer has power -- the power light does not come on. I've unplugged the unit and moved it to a variety of different outlets that I know work.
View 5 Replies View RelatedI have an old WAP54G v3.1 and I want to access the menu but cannot, the IP must have been changed and even resetting does not let me in. What can I do?
View 4 Replies View RelatedI have a WAP54G as my access point, currently it is connected with my BEFSR81 router. I am thinking of changing the access point to a WAP610N for the house. I know that this would work but I was wondering if the WAP54G could be used as a repeater for the outside (I know a lower speed). I know they are two different channels but I wanted a larger range for my wireless. I am on Windows XP, SP2, using Firefox. Can this be done?
View 4 Replies View Relatedi have been using a couple of wap54g units for years now (awesome units!) but its now time to upgrade to "N".is there a newer unit that has "N" ?is there a unit that has a PoE option? also, i really like the ability to switch to larger antennas like the wap54g unit does. i would think that all wireless access units should have removeable antennas and a PoE option!
View 6 Replies View RelatedMy mac has been overwritten on 2 of my APs, they are now totaly different than before and identical ? they now both show 00:90:4C:91:00:01
View 9 Replies View RelatedMy network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies View RelatedI just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedAccording to the information on the bottom of the WAP54G setup screen it can connect to the WRT54G without another WAP54G. What I want to do is use the WAP54G as a bridge to connect my DVD player with an Ethernet connection to the internet via the WRT54G. Both units have the latest firmware updates. When I set it up as I believe it should be the WAP54G has all the lights on but the DVD player cannot connect to the internet.
View 5 Replies View RelatedHow do I connect three or more WAP54G's in bridge.
View 3 Replies View RelatedI have a wrt54gx2 with srx 200 technology recently purchased. I havetwo cabled computers attached. One at one end of the house attached tothe router by ehternet cable, the other attached about 100 ft by ethernet cable.The wireless does not reach to the other end of the house, most likley because that part of the house is an addition with masonary walls and a large masonary firplace. I bought a wap54g access point at the recommendation from someone at linksys to attach to the end of the ethernet run. Since my set up is macintosh, I can't use the wizard disk that came with the wap54g. Linksys support was not support( not expected), I need to know what to do to get this up and running. I am new to this stuff and Linksys get the wireless router with ethernet installed and up and running with my dsl. I thought the same for the wap54g.
View 2 Replies View Related