I'm trying to configure a WAP321 so that I have the same SSID and WPA2 password on both the RV220W and the WAP321 so that i can reach all areas of my clients location.
View 1 RepliesI plan to extend the wireless signal for RV220W as a wireless access points now. Can we use lower end model instead of another RV220W?
View 2 Replies View RelatedHave a WAP321 connected to a Cisco SG200-08P then connected to a Cisco 2901. The main wireless on vLAN 1 works fine. However, the Guest on vLAN 4 (Choose vLAN 4 as per the included docs so guests will be unable to see the production network) will not give an IP to any wireless device. Looking for documentation on getting the Guest radio working. The included documention for these 3 devices do not address how to get the Guest radio to work.Does vLAN 4 need setup on the 2901? Have just 1 internal port on the 2901.
View 14 Replies View RelatedI'm able to to create my main network, but unable to create guest network. Already create CP and when connected to the guest SSID, the guest could still see my main network. How to create Guest network?
View 1 Replies View RelatedI'm setting up a wireless network for a small office with 25 people with approx. 15 on wireless at any time. The office is very long and skinny so I'm looking at a cluster of WAP321's. I'm hoping these will save a ton of money versus buying a controller and more expensive access points.
How do these work for roaming? I tried a search but I've found descriptions of them not roaming at all and descriptions of them roaming but you have to do some kind of pre-authorization right up to they roam with no user interaction, they just roam.
I need the users to be able to roam around the office with no interruption. I don't want to install these and have to rip them out later and put in new ones and a controller. How to find out if the WAP321's will work for roaming.
My b/g/n router is at one end of the house and on the second floor needs to be. I currently have a b/g/n wireless bridge hooked to a LAN port of an b/g/n router that I am using as an access point almost in the center of the house, about thirty feet away with one wall between them. I get good connection speed on an Internet TV that's about 7 feet below the access point with one floor/ceiling between. I get a reliable but slow connection to an Internet TV that is about 20 feet from the access point with two walls between. I get intermittent, slow connections with portable devices near the opposite end of the house on the first floor. Measured horizontally, they are within 15 feet of the upstairs TV that has a slow connection and about 9 feet below it.
The ceiling of my unfinished basement stairwell is a few feet below my router. I am thinking of putting a wireless bridge in the stairwell and connecting it with ethernet cable to an access point located in the crawl space, which is very dry, under the house directly below the upstairs Internet TV. It would be about 12 feet below the TV with a floor and a ceiling/floor between. That location would put it within 15 feet of the wireless devices on the far end of the house that now have a poor connection, with only a floor between. My primary goal is to get a better connection for them, but I'm hoping for a better one to the upstairs TV. My house is of frame construction with mostly plaster interior walls.
I want to use a POE access point under the house because I think it would be easier and safer than running a long extension cord. Looking at POE devices in catalogs, it is often not clear to me whether the device in question expects to be powered over ethernet or expects to power other devices over ethernet.
I have the following questions:
Does my plan sound feasible, and would it be expected to accomplish what I want?
How can I be sure that, when I order a POE access point, it expects to receive power over ethernet, not provide it?
Can POE devices be cascaded? If I do this and find that I did not get the coverage I hoped and, therefore, want to add another POE AP, can I add a POE hub or switch and run cable from it to the additional POE AP? If so, is there any particular monclature for devices that expect to both receive and provide POE? Can such devices receive and provide over any port, or do they have to receive power on a designated one and provide it to the others?
i have following requirement.Wired part of the network is already done.
CiSCO 2800 or 800 router connected to ethernet switch and pcs connected.i want another 5 pcs connect to this LAN through wireless connection distance between wired part and this new location is approximateley 200meters. how can i do this using access points and repeters or any other methods?
I'm trying to extend the range of my wireless network from my house to my workshop, which is about 600 feet away. There are no trees or other objects in between the two buildings. how I could boost my wireless signal to reach that far?
View 1 Replies View RelatedI have an 802.11n/g wireless network throughout my house. I also have several ethernet ports. I want to use the ethernet port to connect to the network and extended the existing wireless network (same SSID). I know AirPort devices from Apple can do this but I wanted to know if anything else could as well. It is too slow when I try to wirelessly extend it (not using ethernet at all).
View 4 Replies View Relatedset up the wireless network at a friend's house, which is a large solid-brick house that winds from one end to the other. The current location of where the cable comes into the house is unfortunately on the far-left end of the house, which means that the right end of the house receives no signal from their DIR-825 wireless N router.
What I've been looking into is the best way to wirelessly extend the wireless signal to the other end of the house. It seems straightforward enough to use an ethernet cable and access point to extend a wireless network, but that is not really a good option for this house. After reading many forum posts (and not being an expert myself) it seems like it may be possible to wirelessly extend the wireless network with another router, although it appeared that this is much less common (if at all possible) with wireless N routers.
what device I need to accomplish what I've described above? Another router, or some kind of access point/bridge? I saw at least one rather expensive wireless N repeater online (a Hawking brand, I believe) but was hoping to avoid that option initially, but if that is the only way to go then so be it :-)
what i am after is, a way to extend my internet in a room that cant connect wireless. i want to be able to connect my ipod touch/ nokia phone / ipad on my home network. i have wireless in the house, But, because of the insulation in the walls and ceiling in this room(kingspan, with the silver foil on it) i cannot get a signal, i am wanting to know if it is possible to some how use the wired connection from my pc in the room and add a wireless dongle(usb) and some how get it to share the connection?
View 5 Replies View RelatedI have a wireless router (TP-Link) which I want to use to extend my wired dorm room cable connection.The "blue" network cable currently goes straight into my laptop and I have no control over its configuration.Is it possible to plug the blue cable into the WAN port of my router and then wire the computer back into a LAN port?BUT that's not really the major problem. Mainly I would like to know how the router must be configured to allow me to use other wireless devices in my room (phone printer etc).Someone told me that I "just" need to use the "bridge" setting but that turned out to be complicated by warnings and messages about other SSIDs.Is "bridge" really the right mode? It seems it's for connecting two wireless networks together.
View 4 Replies View RelatedI have two Aironet 1242AG access points. Currently, one of those access points is in use with an SSID of ABCWIFI.
I want to extend the wireless network to an area that can't be reached by copper or fiber. So, I've purchased another 1242AG. What I'm not sure of is how to configure it. Should I use it as a repeater or in a root-bridge/non-root bridge configuration?
What I'm most confused about is, what do I do with the second radio? Do I use the 5Ghz as the "backhaul" with a completely separate SSID and then broadcast the normal SSID over the 2.4Ghz? Or, do I even use the second radio at all? The key is that the same SSID is used in all locations because the devices in use need to move seemlessly between access points
i have intermittent connectivity on the 2nd router that was installed on the network in order to extend range. 2nd router is connected to the original wireless router by an ethernet cable.
View 5 Replies View RelatedI have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies View RelatedHow do you have the WAP610N and WRT610N using the same SSID? I would prefer to have my WAP610N simply just extend my network instead of broadcasting another.
View 1 Replies View RelatedI want to extend wireless from one building to another. I want the second building's AP to also provide access to wireless clients in that building (small).
Can Engenius or Ubiquiti extend an existing wireless network? It looks like the Engenius ENS200EXT I have would work if I had another one in building 1. It doesn't seem like it's meant to work with other brands.
I have a Ubiquiti Picostation that I could use for this as well if it supports it. The existing wireless router in building 1 is a Linksys model.
I would like to know what to buy to extend the range of my wireless network , which will not reach throughout my house.
Also, I would like to know what the button is for on the front of of the router, since it is not a WPS button, according to ATT.
I've recently upgraded my internet provider to BT and received a BT Home Hub 3 as the new wireless router.Previous to this I was using a wireless Belkin G + MIMO ADSL router (model number F5D9630-4).There are places in the house where the wireless signal is very poor. Connecting to the internet using either of these routers is difficult in these spots. However, since the Belkin is now spare, I've been thinking about trying to use it as a low cost repeater (i.e. free) to extend the wireless range in the house.There are several good articles that I've found on this site which address the connection of two routers together (e.g. John Will's article on connecting two SOHO routers is a good example), but they rely on an ethernet connection between the two routers. Any way to establish a wireless link between the two routers to extend the range of the current wireless network.
View 9 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View RelatedI've a WLC 2106 and it is running IOS version 7.0.240. I am trying to setup a wireless mesh and used the Ethernet bridge port on the MAP to extend the network. The wireless mesh works fine but I can not get the switch to work that is connected to the ethernet port on the MAP.I'm using two different Access points. I'm using a Air Cap 3502i as the RAP and a Air Lap1142N as the MAP.The switch port that is connected to the RAP and MAP is configured as the following:
switchport mode trunk
switchport trunk native vlan 2
switchport trunk allowed vlan 10,20,30,40
[code]....
The wireless mesh between the RAP and MAP works fine. I can connect a device to the MAP wirelessly and access the network with no problem but I can not get anything to work that connects to the switch that is connected to the MAP ethernet port.
I have the WRT610N, and I was wondering if there is a way to repeat the 5GHz network to extend the range.I am trying to stream content from a Blu-Ray player, and while the 2.4GHz network reaches, the signal is very weak. The 5GHz network doesn't reach, but I would prefer to stream content through that network than the 2.4GHz.
View 7 Replies View RelatedI have a E4200v2 i also have a Airport Extreme I want to use this to extend my wireless range in my house? I've played around a little tring to configure the Airport extreme but can't seem to get it to connect to my E4200v2? Can you mod the Airprt Extreme with dd-wrt or something that might unlock some of the features?I can't stand the interface. The E4200v2 is brand new.
View 1 Replies View RelatedI am trying to extend my home network into my basement with both wired and wireless connections. I have a WRT120N upstairs, which is connected to my cable modem. I have an E1200 in the basement, which I have connected with a LAN port. DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet. They are getting an IP address from the upstairs router, but can't get past the gateway.
View 1 Replies View RelatedIs it possible to configure the apple airport express to extend a linksys wrt120N wireless network? if so how?
View 2 Replies View RelatedI just got a cisco RV220W and I try to connect it on my wireless network as client, but it doesn't work.
View 1 Replies View RelatedI am using the RV220W with the latest firmware, I disabled all the four APs and also disabled the Radio, but the "Wireless" green light on the front panel still ON, why? How can I completely turn off the wireless?
Quoted from manual: WIRELESS—The Wireless light is green when the wireless module is enabled. The light is off when the wireless module is disabled.
Moreover I tried to disable the "Radio" while enabled one AP, I found that I can still connect to that AP, so what is the Radio's Enable/Disable used for?
I provide support for a small business network. ISP: Silo Wireless (wireless point to point with ISP) Router: Cisco RV220W Wireless-N Network Security Firewall
The router is configured with two wireless access points with SSIDs: "abracadabra" and "abracadabra-guest". The only difference between these two wireless networks is their passcode. Up until now I have had no problem connecting devices to either wireless network.
My problem lies with an HP Pavilion laptop running Windows Vista Home Premium 32-bit that I'm trying to connect to the "abracadabra" wireless network.
Network and Sharing Center shows "Identifying" for a while and then shows "Unidentified network" with no local or internet access. Wireless network connection status says that Media State is Enabled, Speed is 54Mbps and Signal Quality is Excellent. Network Connection Details shows that DHCP is Enabled but it's getting an Autoconfiguration IPv4 address of 169.254.107.138...
The laptop is running ESET Nod 32 Antivirus 5 and Windows Firewall and I've disabled Windows Firewall on the Wireless Network Connection. I've also tried re-installing the wireless nic driver, it's running the latest from Windows Updates.
what really gets me is that the laptop can connect to "abracadabra-guest" fine and access the internet
I have a e4200 Linksys upstairs and the range in parts of house is weak weak. I need more access points. Can I add another router downstairs on another cat5 and make it act as access point? What other options?
View 4 Replies View RelatedI have a new Siemens router and have set up my old LinkSys router as a switch (set DNS outside the IP range of the primary router, disabled DHCP server, connect LAN to LAN port).The SSIDs are still different. As a result each device now sees 2 networks and although internet GW is available from either connection, not al resources are shared across the network. There is one driveshare (with wired connection to the secondary switch) which cannot be seen by some of the wireless resources on the same secondary network.Questions:1. How can I set up the NW config such that it is seen and behaves like one physical network, anbd roaming devices pick up the signal from the strongest access point?
View 3 Replies View RelatedHow can i use a router to extend the ip addresses of a separate network? I have been given a subnet mask of 255.255.255.248 which has given me 6 ip addresses to access the internet. How can i use a router to allocate extra ip addresses and route them to the internet ?
View 1 Replies View RelatedI have a network of one router which servers both LAN and wifi, my laptop can only use wifi to connect but the range of the router doesn't reach the third floor. I need a way to either extend or create a second hot spot but I'm not sure whether to use a repeater, a hub or a switch? this is my first time dealing with a network
View 3 Replies View RelatedI am having an issue where I can't get to external network sources via my sub interface which is attached to a 192.168.10.X VLAN I created to for Guest wireless traffic. The internal interface is a 10.5.X.X network. I can get out the external interface, but anything that we have A records for such as our mobile iron server that we can hit from the outside via https and an external IP can't be hit from the subinterface at all. Would this be a DNS rewrite issue or inspection problem?
View 3 Replies View Related