Cisco Wireless :: 1142 Access Point Signal Pulsing

Aug 1, 2012

I've recently set up a guest wireless in my office, using a WLC 2504 controlling 4 1142 APs. They have been working great for about a month, but as of yesterday, the Wifi signal from 2 of the APs began to pulse - 5 seconds on, 1 second off - which makes it unusable. [code]
 
All APs are receiving PoE from their last 3750 (at default levels). I've cycled the individual APs, as well as the WLC, but the issue remains.Except for the initial 3750 directly connected, all other 3750's are different.

View 8 Replies


ADVERTISEMENT

Cisco Wireless :: 1142 Access Point Blinking Green

Feb 15, 2012

I'm having a strange issue with an 1142 AP.  I have a 5508 WLC at my corporate HQ and have AP's in many locations, connected by MPLS WAN.  I have one site where the 1142 is blinking green and doesn't associate with the WLC.  I have tried a different switch port with the AP (didn't work) and I know that the switch port is good because I have a 1252 that works just fine at this remote location.The really weird part is that the AP is blinking green, but the switch port shows that it is not connected and the green port light on the 3560 switch is not lit.  I have verified wiring in the closet, but unfortunately the 1142 AP is hanging 40ft high in a shop and I don't have access to it.Is it possible that there's a bad rj-45 termination that is allowing PoE to the AP, but no data?

View 14 Replies View Related

Cisco Wireless :: Setting Up 1142 Access Point With DHCP

Aug 10, 2011

I am setting up an autonomous 1142 Access Point. The intended goal is to get it accessible though 2 SSIDs:Private: VLAN3 (our internal data VLAN)Guest: VLAN98 (our DMZ/Segregated VLAN)At present, our VLAN3/internal users get DHCP addresses from x2 Windows DHCP servers. Eventually, the DMZ VLAN connections will get their IP addresses from a switch in our DMZ VLAN.At the moment, I am able to authenticate with the Access Point through the VLAN 3 SSID but never get an IP address. I have posted the switch port config below as well as the Access Point config.

View 2 Replies View Related

Cisco Wireless :: 1142 - Maximum Recommended Clients Per Access Point?

Jan 24, 2013

We are about to upgrade our training facilities wireless and i have a few questions regarding the number of active clients we should target our design for.
 
We would be using 1142 and 3502I access points. I was thinking that  based on the belo we'd be able to support around 30-40 clients per AP.
 
Protocol
Type of web use
Amount of bandwidth allocated per device

[Code]....

View 4 Replies View Related

Cisco Wireless :: Extend Signal For RV220W As Access Point?

Mar 25, 2012

I plan to extend the wireless signal for RV220W as a wireless access points now. Can we use lower end model instead of another RV220W?

View 2 Replies View Related

Linksys Access Point :: WAP610N Wireless-N Repeating Signal

Sep 14, 2011

Is it possible to use  WAP610N Wireless-N Access Point repeating signal with another  WAP610N Wireless-N Access Point?what the range of signal when using a single WAP610N Wireless-N Access Point ?How many devices can connect to WAP610N in the same time?

View 1 Replies View Related

Access Point Or Wifi Signal Booster / D-link Wireless N Gigabit Router

Jan 2, 2013

Got 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?

View 5 Replies View Related

Linksys Wireless Router :: Setup Wrt54g As Access Point To Extend Signal?

Aug 17, 2011

how do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
 
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?

View 1 Replies View Related

D-Link DIR-825 :: Getting Access Point And Signal Strength?

Nov 21, 2011

I have connected my DIR-825 to my cable modem through the network ports and completed the configuration.  Everything works fine, I am able to connect through wireless to the DIR-825 and access the internet.  I had to do this as my cable modem is also wireless and does not allow another router to be connected through the internet connection, but I want to get a better signal stength than the cable modem.When I am not wireless connected, I can see the two bands at full strength in the view available wireless networks screen.  As soon as I connect to either the 2.4 channel or the 5 channel, the signal strenth of the channel I'm connected to drops to horrible, while the non-connected one still shows at full strength.i tried disabling one of the channels, but as soon as I connect to the other, that channels signal strength still drops to horrible.

View 1 Replies View Related

Linksys Access Point :: Best Way To Expand Signal WAP610N

Aug 22, 2011

I have a duplex on the first floor have the adsl router from the telephone company can not be replaced,the switch from a cable that comes into a room on the second floor where it was connected to an access point Linksys Wireless-N Access Point with Dual-Band WAP610N the signal on the first floor, however, comes down and in some cases just no signal. 

View 3 Replies View Related

Using Repeater To Extend Signal Of Access Point Both TP-Link TL-WA901ND?

Jan 9, 2012

Im in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?

View 1 Replies View Related

Linksys Access Point :: WET610N Range And Signal Strength?

Nov 9, 2011

I'm trying to use the WET610N as a sort of access point/range extender for a single device, a remote monitoring system installed in a barn. It records temperature, power use, etc, and reports it to the internet. The barn is about 250 feet from the house where the wireless router is installed. There will be very little data flowing over the link.Setup on the WET610N went fine, and it saw the remote router at 10% strength and connected to it fine. However, when I attempt to get Status, the screen shows the headings on the left and no data on the right. Attempting to access the internet through the link on my MacBook Pro failed.

View 6 Replies View Related

Linksys Access Point :: Amplifying WRT160N Signal With Secondary AP

Mar 13, 2012

My Linksys Wireless-N router/access point (WRT160NV2) is connected to the internet in my primary residence, delivering 35mbps. I purchased a commercial Engenius product (EAP9550) to amplify the wifi signal over to a secondary house (about 180 ft away, traveling through 3 walls). Configured as an access point, the EAP9550 received and showed signal, but there was zero connectivity. The tech support at Engenius has advised me to configure the EAP9550 as an access point. My linksys router continues to deliver wireless signal for its range, but is only showing (not giving) full connectivity to the secondary access point. 

View 1 Replies View Related

Linksys Access Point :: Increase Signal Strength And Range Of WAP54G?

Jan 19, 2009

I have a WAP54G and the signal strength and range is not that great; unit manufactured in 04/2007.  I have firmware version 3.04 dated Oct 31, 2005.  Customer support is suggesting I upgrade the firmware to 3.04.03 but I am sure it will really do anything to the signal strength and range.  Also, they suggested I download new drivers for my desktop wireless card. 

View 9 Replies View Related

Cisco :: 1142 And 1242 G Clients With Weak Signal Strength

Apr 8, 2012

I am trying to setup two Cisco 1310 bridges (AIR-BR1310G-A-K9-R) for connectivity between two buildings.  No external antennas have been setup yet and I am just setting the basic configuration.One is running c1310-k9w7-mx.123-8.JEA3, the other c1310-k9w7-mx.123-7.JA1,setup as a root-bridge, the other as a non-root bridge.However, even after disabling authentication and encryption, both units are still not talking to each other.Maybe a second set of eyes can see an issue?

View 7 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Cisco Wireless :: 5508 / 1142 / Access Points Resetting?

Sep 2, 2010

Access points 1142 controller 5508 running code 6.0.196.0 When you set the access point port speed with "config ap duplex full speed 1000 all" the access points leave the controlle and do not rejoin. I have had to reset the the access points manually with a power down and hold the reset button.

View 13 Replies View Related

Cisco Wireless :: 2504 Controller With 3 Aironet 1142 Access Points

Mar 16, 2013

I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.

View 5 Replies View Related

Cisco Wireless :: 3500 - Upgrading Large Number Of 1142 Access Points

May 21, 2012

I am upgrading a large number of 1142 access points with 3500's does and one know if the back plate for the 1142's can be reused for the 3500's.

View 4 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Linksys Access Point :: Repeat WAP54G Access Point?

Aug 25, 2011

What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G. 

View 4 Replies View Related

Linksys Access Point :: WRT120N - Cannot Connect To An Access Point

May 10, 2013

I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
 
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.

View 1 Replies View Related

Linksys Access Point :: Configure WRT120n As An Access Point?

May 1, 2012

Is it possible to configure WRT120n as an access point?

View 1 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related

Linksys Access Point :: Way To Find Mib For WAP54G Access Point?

Feb 10, 2012

I have tried to find mib for my Linksys WAP54G acces point  without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved