I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?
Does aps work with Wcs ?? .
View 4 Replies View Relatedeveryone can connect to the 1040 ap except my laptop and another one. for some reason it stopped showing , it was working fine and out of the blue nothing.
View 2 Replies View RelatedWe setup some new CAPWAP AP 3602E in the network and configure the DHCP server option 43 , but the WLCs still cannot detect the APs , Do you know if there any new way to troubleshooting?
WLC: 5508 version: 7.2.103.0
SW:3750E
AP: AIR-CAP3602E-C-K9
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)
i have IO digital cable and internet and they offer free WiFi which i do not use my modem is wired to my pc but over the last few weeks my connection has been sluggish now is it possible for one of my neighbors to be using my internet?
View 2 Replies View RelatedI have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies View RelatedI'm looking at the spec sheet comparing Cisco WLCs and I see that the 2504 has a bandwidth max of 500mbps. Just to be clear, not all of the traffic from the APs goes through the WLC does it? In this setup, the APs would be plugged into a PoE switch as well as the WLC. The only traffic to WLC would be the CAPWAP tunnel, CleanAir info, etc right? All other traffic should just be handeld at the switch right?Also, does the 2504 licencing include CleanAir in the price?
View 17 Replies View RelatedI have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
I am trying to configure two AP-management interfaces to accept CAPWAP on different ports using the option "Enable Dynamic AP Management". One of them uses public ip address. However, I getting the message "Ignoring discovery request received on non-management interface ..." on this.
The controller is 5508.
I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread ([URL]) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes
!
version 12.4
no service pad
[Code].....
i have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?
View 3 Replies View RelatedI have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies View RelatedI am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
I understand that Cisco *wants* the APs to be directly connected to the new 3850.I have a few questions. Unfortunately, I think I know the answers. I just want to confirm.
a. When MA/MC is enabled on the 3850, does the 3850 start intercepting *all* CAPWAP packets it sees (much like CDP)? Even non-Cisco CAPWAP packets?
b. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 is NOT in MA/MC mode?
c. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 IS in MA/MC mode?
What I'm afraid of is:
a. yes, yes
b. yes
c. no
From the Q&A page:Q. Does the Cisco Catalyst 3850 support indirectly connected access points?A. No. The Cisco Catalyst 3850 switch will always terminate the CAPWAP tunnel locally. Pass-through mode or indirectly connected access point is not supported at this time.
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies View RelatedClarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies View RelatedI am trying to create a welcome screen for people who join the guest network on my aironet 1040.Webpage pass-through is really what I want but I know that doesn't work on a 1040.What does: IP redirect, Conditional Web redirect or Splashpage redirect?
View 1 Replies View RelatedWe are currently using several AP's in our organization. And in this one AP i want to give a user the power to change the password of the wireless network to prevent miss use. I was wondering if it was possible to create an account who only has the privilege to change the WPA key?? I want to prevent that he will accidently change other settings.
View 5 Replies View Relatedwe have several AP1040 in the office, but the latter is a Dual Band 2.4 GHz and 5 GHz. And we have problems with all workstations MAC OS X gets a lot of disconnections during the day, the strangest thing is that the OS X community is aware of the problem, and their only recommendation is to buy the external Aironport has better hardware.
View 3 Replies View RelatedI have a Cisco aironet 1040.
On my Accespoint i have 2 vlans: 1 for my wifi phones and 1 for my network.Wifi Lan has the SSID LAN with WPA enterprise authentication to a radius server(ms server 2008).Wifi Phone has SSID PHONE and vlan 50 with local radius authentication.This Works all fine, Except when i enable AP for my wifi phones. When AP is enabled the authentication for my lan doesn’t go to my server but local.How do I configure my accesspoints so that the cisco phones use the local radius server with AP and my windows computers connect using the ms radius server?
I'm working on setting up an Aironet 1040 Wireless Access Point for my company. It's my first time setting up something like this, and I've run into a bit of trouble.
I created my first SSID easily enough, following the manual and guides online. I set up VLAN 1 as my native VLAN and linked it to my SSID with the encryption and security that I was told to use and it works great. However, my boss asked me to set up a second connection as well for guests at the office, and this is where my trouble starts.
I created VLAN 2, and then another SSID which I linked here. I set up encryption and security the same way, and I can see the network when I open up my network and sharing manager. I can connect to the network as well, but I either get a spinning blue icon where my signal strength indicator is or a few bars with a yellow caution sign, and Windows says 'Identifying...'. I've compared the two SSIDs using the console and the GUI and I can't seem to spot any obvious differences between them.
The following messages are filling up my syslog.
*spamApTask0: Nov 09 15:59:29.071: %LOG-3-Q_IND: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
*spamApTask3: Nov 09 15:59:27.616: %CAPWAP-3-REASSEM_SPACE: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
What could be causing it? I am using 1524 APs in a Mesh environment with a WLC 5508 (7.0.116.0) which is connected to a H3C switched network.
The MAC addresses above are from my MAPs and I don't think I am getting it from the RAPs.
Looking for some training on the 2500 series controller and 1142 or 1040 AP's preferably.
View 10 Replies View RelatedCan I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies View RelatedIs Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies View RelatedI want to know the CAPWAP protocol.
View 1 Replies View RelatedRecently we upgraded a switch with an image from the repository in LMS. After the installation of the image it seemed corrupt.
My question now is : Can we do a MD5 checksum on all the images in the local repository to verify that all images are ok to use?
I heard my brothers' conversation in our house. One was asking another, if he is downloading things. The other one replied, saying no, he didn't. And then the one that was asking said, he knew he was lying. He can detect and monitor that person's IP address to know enough if the other person is downloading or not.
View 6 Replies View RelatedI have setup a Cisco Aironet 1040 to connect to our Radius server which I have also configured.
I can successfully connect up any Iphone or Ipad but I cannot get any laptop to connect.
I have attached the logs showing the Iphone Successfully logging in and the Laptop Failing. Every single failure in the Event log for NPS comes up with
Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information.
User:
Security ID: NULL SID
Account Name: scottd
Account Domain: AMSLAN
[Code].....
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies View RelatedI want to join the AIR-AP1121G-E-K9 LAP to an 2504 WLC with software release 7.4.x .In the compatibility matrix i saw that it's just possible if the WLC has the software version of 7.0.x.So my questions are:
1. Why it's needable to upgrade the WLC from 7.0.x to 7.4.x?
2. Is there any possibility to join the AP1121G to an 2504 WLC with 7.4.x version?
3. What's the difference between the releases 7.0.x and 7.4.x