Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 RepliesI am trying to configure two AP-management interfaces to accept CAPWAP on different ports using the option "Enable Dynamic AP Management". One of them uses public ip address. However, I getting the message "Ignoring discovery request received on non-management interface ..." on this.
The controller is 5508.
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
I'm looking to deploy a 2504 controller and some AP1142s but would like to provide the client with an alternative, lower initial-cost option in my proposal. I've been researching the AP541N access points but several areas of their implementation seem unclear to me.
Clustering: For the clustering feature is it necessary for the network to have other SBCS components (500 series platforms)? All of their other features are either unapplicable to or already implemented in the network in question; if I have to add another appliance I would rather go the LWAPP route and use a true WLC.
What are the cababilities of clustering? Can I implement some form of wireless resilience by spacing APs closer together than necessary and they will lower transmit dBm and intelligently respond to attempt to cover a new cell where an AP has gone down?
What about roaming? I believe Cisco advertises this as part of a small business voice solution. A client roaming between two access points in the same mobility group (cluster?) on a wireless voip phone should be able to keep connection, as it's analogus to some critical UDP communications that are going to take place on the clients.
I have an older Linksys WRVS4400N Version 1.1 VPN Router. I have it set to run in mixed mode G/N. I still can only get connection speeds of 54 Mbps though. How can I get my wireless N clients to see 300 Mbps speeds?
View 1 Replies View RelatedWhen I enable the debug with ?todo=debug shall I see more info in the logs ?How to stop the debugging ?How to print the logs ?What is the difference with debug and ppp_debug ?What is the effect of the sendlog command ? I didn't receive any email with a log !
View 3 Replies View RelatedMy Vostro 3750 unable connect to my wireless router due to no wireless SSID is shown & Wireless Connection Network also not listed...
i can't enable Intel My wireless Technology... it's stated Adapter not found....
i have check inside Device Manager > Network adapter... my device is enable..
also i check in Network Connection... My device is enable...
We setup some new CAPWAP AP 3602E in the network and configure the DHCP server option 43 , but the WLCs still cannot detect the APs , Do you know if there any new way to troubleshooting?
WLC: 5508 version: 7.2.103.0
SW:3750E
AP: AIR-CAP3602E-C-K9
I´m looking to a project where we want to start using Autonomous AP with possibility to change to controller based on near future.
Will Cisco Aironet 1040 Series Access Points allow us to change from IOS to CAPWAP when needed? I read some posts about the oposite process (CAPWAP to IOS) so I think it´s possible on both way. Can some one confirm this to me?
We have had several APs disassociating from our controllers. The alerts say, Message: Access Point 'AP-xxxxx' associated to controller '10.x.x.x' on port number '0'. Reason for association 'Dot11g Mode Change. I have read several posts that point out that you should have QoS implemented to prioritize the CAPWAP traffic. I'd like to know if someone has implemented QoS and whether it has been successful in stopping the APs from disassociating. And if it has been successful do you have any configuration examples for the ports attached to the AP and controller as well as the QoS configuration?
We have several sites with AP1142's and 3500's. We have 2 5508 controllers. We are broadcasting 2 SSIDs of which one is in HREAP mode and the other is in local mode. Each of our sites have MPLS circuits.
Here is an example I found on Cisco which I believe can be used for CAPWAP as long as you change the ports to 5246 & 5247 instead of 12222 & 12223.
Example Router Configurations #
This section contains router configuration examples to be used as guides when addressing CS6 remarking or LWAPP control traffic load.
#
This example uses LWAPP APs on the 192.168.101.0/24 subnet, and two WLCs with ap-managers at 192.168.60.11, and 192.168.62.11. (code)
I have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used ?
View 7 Replies View RelatedI'm looking at the spec sheet comparing Cisco WLCs and I see that the 2504 has a bandwidth max of 500mbps. Just to be clear, not all of the traffic from the APs goes through the WLC does it? In this setup, the APs would be plugged into a PoE switch as well as the WLC. The only traffic to WLC would be the CAPWAP tunnel, CleanAir info, etc right? All other traffic should just be handeld at the switch right?Also, does the 2504 licencing include CleanAir in the price?
View 17 Replies View RelatedI have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
How can i find the list of features supported in ASR for various license
1) IP Base
2) Advance IP Services
3) Advanced Enterprise Services.
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies View RelatedI am facing this particular issue while providing Cisco unified Wireless solution to the customer. We are having CAPWAP 1252 APs controlled by WLC.
Scenario: 50 persons sitting in a hall with closely packed chairs using wireless simultaneously. Wireless access provided by patch antenna at a height of 11m from the user. As one AP can server 25 users, 2 APs are placed with antenna directions facing the compact users. Each users gets very good signal from these two APs.
Whether there will be serious interference and client association issues in this scenario? once one AP associates 25 clients, whether other 25 clients associate completely to other AP?
I understand that Cisco *wants* the APs to be directly connected to the new 3850.I have a few questions. Unfortunately, I think I know the answers. I just want to confirm.
a. When MA/MC is enabled on the 3850, does the 3850 start intercepting *all* CAPWAP packets it sees (much like CDP)? Even non-Cisco CAPWAP packets?
b. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 is NOT in MA/MC mode?
c. If I have a WLC 5500 upstream from the 3850, would APs hanging off a downstream 2960 be able to register to the 5500 through the 3850 when the 3850 IS in MA/MC mode?
What I'm afraid of is:
a. yes, yes
b. yes
c. no
From the Q&A page:Q. Does the Cisco Catalyst 3850 support indirectly connected access points?A. No. The Cisco Catalyst 3850 switch will always terminate the CAPWAP tunnel locally. Pass-through mode or indirectly connected access point is not supported at this time.
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies View Relatedwe need to use Nexus technology over 6500 based VSS in entreprise ?
View 1 Replies View RelatedThe following messages are filling up my syslog.
*spamApTask0: Nov 09 15:59:29.071: %LOG-3-Q_IND: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
*spamApTask3: Nov 09 15:59:27.616: %CAPWAP-3-REASSEM_SPACE: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
What could be causing it? I am using 1524 APs in a Mesh environment with a WLC 5508 (7.0.116.0) which is connected to a H3C switched network.
The MAC addresses above are from my MAPs and I don't think I am getting it from the RAPs.
I want to configure 5585x Active/Standby with 2 nexus switches utilizing VPC technology. New ASA 8.4 supports etherchannel so I want to plugin 2 cables from ASA1 to sw1 and sw2 and 2 cables from ASA2 to sw1 and sw2? Is this a valid design? how would I configure that? Any design document on that?
View 1 Replies View RelatedCan I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies View RelatedIs Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies View Relatedis this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedI am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies View RelatedCan the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies View RelatedI have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedWhat is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies View RelatedWe have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies View RelatedI am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedI need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies View Related