Cisco Wireless :: Does 526 Controller Use LWAPP Protocol
Dec 3, 2008Can the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies
ADVERTISEMENT
Cisco Wireless :: Connect 1130 Lwapp To Controller In DMZ?
Aug 5, 2012i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 Replies View RelatedCisco Wireless :: 1140 LWAPP / Local Bridge On Controller AP?
Sep 5, 2011I have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies View RelatedCisco Wireless :: Converting 1242ag To And From LWAPP
Apr 5, 2013is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedCisco Wireless :: Upgrading A 1242 AP From IOS To LWAPP
Sep 12, 2011I am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies View RelatedCisco Wireless :: Converting 1040N Autonomous AP To LWAPP
Oct 5, 2011I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedCisco Wireless :: C1240 LWAPP Software Differences?
Oct 15, 2012What is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies View RelatedCisco Wireless :: AP-1041N LWAPP Reboot In Loop
Jan 24, 2012We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
Cisco Wireless :: Downgrade AIR-LAP1142N-A-K9 LWAPP To Autonomous
Nov 14, 2012I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
Cisco Wireless :: LWAPP 1242 Radio 0 Shows Down
Jan 14, 2012I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies View RelatedCisco Wireless :: 5500 / Restart LWAPP Which Is Up For 200 Days?
Jan 29, 2013I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedCisco Wireless :: Upgrading 1252s From Autonomous To LWAPP
May 22, 2012I need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies View RelatedCisco Wireless :: AIR-AP1252AG Autonomous AP Can Be Changed To LWAPP AP
Aug 25, 2011I would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies View RelatedCisco Wireless :: 1242 LWAPP AP Mode Bridge
Jul 27, 2011I try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View RelatedCisco Wireless :: Converting AIR-SAP2602i-s-k9 From Autonomous To LWAPP
Feb 26, 2013I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
Cisco Wireless :: Aironet 1250 LWAPP To Autonomous Downgrade?
Aug 25, 2010upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedCisco Wireless :: Lwapp 1242ag Doesn't Show Mesh
Oct 10, 2011I'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies View RelatedCisco Wireless :: How To Convert AIR-AP1041N (autonomous) To AIR-LAP1041N (lwapp)
Sep 11, 2011some days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View RelatedCisco Wireless :: Lwapp 1130 - Error / Command Is Disabled
Jan 21, 2012I have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
View 31 Replies View RelatedCisco Wireless :: 819 Work Group Bridge Through LWAPP Network
Jan 21, 2013We are connecting a cisco router (819) to wireless lan network (lwapp) through its wireless interface.
clients ---> 819 ---->AP (WGB) ------ lwapp ----- AP ---> LAN ---> servers.
since the clients are on the same subnet as the the VLAN on the lwapp, everything works great.When we add a new L3 VLAN on the 819 router, and we try to ping the clients from the servers, the packets can reach the clients but never received by the servers back. it seems like the bridge is dropping the packets when they go back from the client to the servers.when we use a GRE tunnel from the 819 to the LAN, everything works great.
Cisco Wireless :: Converting 881W From LWAPP To Autonomous Mode
Aug 19, 2010I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
Cisco Wireless :: WLC 5508 - AP LWAPP With 2 SSID / DHCP Differences?
Jul 22, 2012I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
Cisco Wireless :: 5508 - Lwapp Capwap Technology Clarifications
Jul 10, 2012Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies View RelatedCisco Wireless :: LWAPP Mode To Autonomous Conversion Aironet 1262
Mar 13, 2013we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies View RelatedCisco Wireless :: 7500 LAP Won't Join WLC / Lwapp Discovery Request Rejected
Sep 20, 2011We are setting up a WLC 7500 for the first time and are having a hard time trying to connect an LAP to the WLC. We have 1042 Access Points.Reason for last unsucessful attempt: to many concurrent ap image downloads
-Last Error Occurred: Lwapp discovery request rejected
-Last Error Occurred Reason: Too many concurrent AP image downloads
We only have 1 AP plugged in so far and it does recieve an IP address from DHCP.
Cisco Wireless :: AIR-AP1242AG-E-K9 Unable To Join WLC 2504 After Upgrade To LWAPP
Sep 10, 2012I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies View RelatedLinksys Wireless Router :: WRT300N Wireless Routers Are Compatible With LWAPP Configuration?
Nov 28, 2011Whether the Linksys WRT300N wireless routers are compatible with LWAPP configuration?My school lab setup uses Cisco integrated services routers with NM-AIR-WLC6-K9 network modules as controllers in the LWAP network. The controller accepts configuration without error but does not pick up or seem to see the WRT300 AP routers, so cannot push out basic LWAP config info
View 1 Replies View RelatedLinksys Access Point :: Can WRT300N Wireless Router Be Used As LWAPP Device
Nov 28, 2011Can a Linksys WRT300N wireless router be used as an LWAPP AP device?
View 1 Replies View RelatedCisco Wireless :: 4404 Guest Anchor Controller With 5508 Foreign Controller?
Aug 12, 2012I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedCisco Wireless :: 5508 Foreign Controller And 4400 Anchor Controller?
Jun 2, 2013We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedCisco Wireless :: 5500 / Controller Versus Cloud-based (Controller)
Mar 31, 2013We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies View RelatedCisco Switching/Routing :: 2125 Wireless Controller Without Anchor Controller Just Using Existing Hardware
Dec 6, 2012I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
Cisco :: Maximum Nodes For 1524SB LWAPP AP?
Mar 21, 2012Someone has mentioned only 25 nodes are supported by the 1524SB and that one AP gets bogged down by 20 nodes or more.
View 0 Replies View Related