I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 RepliesI am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies View RelatedI try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View Relatedwe are using wism 4404 code 4.2 , we are using this old code becuase of 1250 mesh APs, now when a user connect to our network and he is using intel proset software he can see details of our AP, like mac, type and AP ip address 9 which in this case it the controllers ip address) is there a way we can prevent the ap from showing it?...we will be doing an upgrade to 7.0.230 soon. will the upgrade takes care of this problem or there is a way to fix it.
View 5 Replies View RelatedWhen I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies View RelatedI Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies View Relatedis this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedCan the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies View RelatedI have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedWhat is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies View RelatedWe have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedI need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies View RelatedI would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies View RelatedI need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 Replies View RelatedI have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies View Relatedupgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedI'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies View Relatedsome days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View RelatedI have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
View 31 Replies View RelatedWe are connecting a cisco router (819) to wireless lan network (lwapp) through its wireless interface.
clients ---> 819 ---->AP (WGB) ------ lwapp ----- AP ---> LAN ---> servers.
since the clients are on the same subnet as the the VLAN on the lwapp, everything works great.When we add a new L3 VLAN on the 819 router, and we try to ping the clients from the servers, the packets can reach the clients but never received by the servers back. it seems like the bridge is dropping the packets when they go back from the client to the servers.when we use a GRE tunnel from the 819 to the LAN, everything works great.
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies View Relatedwe have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies View RelatedWe are setting up a WLC 7500 for the first time and are having a hard time trying to connect an LAP to the WLC. We have 1042 Access Points.Reason for last unsucessful attempt: to many concurrent ap image downloads
-Last Error Occurred: Lwapp discovery request rejected
-Last Error Occurred Reason: Too many concurrent AP image downloads
We only have 1 AP plugged in so far and it does recieve an IP address from DHCP.
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies View RelatedWhether the Linksys WRT300N wireless routers are compatible with LWAPP configuration?My school lab setup uses Cisco integrated services routers with NM-AIR-WLC6-K9 network modules as controllers in the LWAP network. The controller accepts configuration without error but does not pick up or seem to see the WRT300 AP routers, so cannot push out basic LWAP config info
View 1 Replies View RelatedCan a Linksys WRT300N wireless router be used as an LWAPP AP device?
View 1 Replies View RelatedI'm using two cisco 1242 AG access points to configure WDS feature. I've named the accesspoints as AP1(acts as WDS) and AP2. Since I've only two accesspoints, I've configured the AP1 to act both as a WDS and as a regular accesspoints.Further I'm using the local radius server within the AP1 to authenticate both clients and infrastructure accesspoints. And both APs are connected to a router (which act as a dhcp server) via a unmanageble switch and both accesspoints are getting registered with WDS.But the issue is when I tried to connect to the configured SSID, it promts me a "authentication window" but after entering the configured username and password, i'm not getting authenticated by the AP.
I've attached the configurations of both APs to for your reference and I've used the following cisco document as a guideline to crate the WDS. [code]
I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.