i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 RepliesI have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
View 31 Replies View RelatedCan the AIR-WLC526-K9 be used for any other access points besides the AIR-LAP521G-A-K9 access points? Does the 526 controller use the LWAPP protocol?
View 3 Replies View RelatedI have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies View RelatedLooking to set up a small office cheaply and quickly and was thinking about ordering a 2006 and some 1130s off EBay. Are the lightWeight 1130s compatible with the 2006?
View 9 Replies View RelatedWe recently acquired a 4404 Cisco controller for our network and have been adding our 1200 and 1130 Access points to the controller.This was accomplished by upgrading the APs to LWAPP and then they would automatically be discovered by the controller and then join. Lately, new 1131 APs that have undergone the same process, are not joining the controller. They are discovered but then the close the connection. We are running a flat network so all devices are in the same subnet.Software Version of the controller 6.0.188.0. [code]
View 5 Replies View RelatedI convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies View RelatedI am struggling with the following issue. I have 6 1130 Accesspoints in lightweight mode connected to a 2106 wlan controller which runs software version 7.0.98.0. Everything seems to work fine. Clients can connect to the wifi network. However, they don't get an ip address from the dhcp server which is on the same subnet as the wlan controller. See attached screenshots for configuration. I have also tried the internal dhcp server of the wlan controller, but the same problem remains.
The logs says: Dropping primary discovery request from AP e8:b7:4x:xx:xx:xx - maximum APs joined 6/6 There are 6 AP's connected
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedI am trying to upgrade an autonomous IOS 1242 AP to LWAPP and I am having an issue with finding the right code to complete the upgrade. I have upgraded the AP to c1240-rcvk9w8-tar.124-21a.ja2.tar, but now I think I need a JX version of code to have it join a controller, and I can't find this anywhere on the Cisco site.
View 5 Replies View RelatedI have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies View RelatedWhat is the difference between WIRELESS LAN LWAPP and WIRELESS LAN LWAP RECOVERY images? I believe the RECOVERY is used in the upgade process - but what is the other used for?
View 1 Replies View RelatedWe have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies View RelatedI am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedI need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies View RelatedI would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies View RelatedI try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View RelatedI need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
I know what the problemis i need to tell the AP what the mac of the switchport is but i can not figure it out because it is a CATos Switch?on a IOS I would just use the Show interface command and use the bia but i dont know how to figure out the bia on a CATos?
View 3 Replies View Relatedupgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies View RelatedI'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
View 5 Replies View Relatedsome days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies View RelatedWe are connecting a cisco router (819) to wireless lan network (lwapp) through its wireless interface.
clients ---> 819 ---->AP (WGB) ------ lwapp ----- AP ---> LAN ---> servers.
since the clients are on the same subnet as the the VLAN on the lwapp, everything works great.When we add a new L3 VLAN on the 819 router, and we try to ping the clients from the servers, the packets can reach the clients but never received by the servers back. it seems like the bridge is dropping the packets when they go back from the client to the servers.when we use a GRE tunnel from the 819 to the LAN, everything works great.
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
I need raise a especial configuration to 34 APs LWAPP associated to WLC 5508 with IOS 7.0.220
This is the Scenario:We have 34 APs LWAPP with 2 SSID (Corporative & Guest), with 2 DHCP different. The Guest SSID receive IP to DHCP from WLC while SSID Corporative receive IP from Microsoft DHCP. The AP On Site are Local and the Foreign AP are configured like H-REAP (H-REAP Local switching and Learn Client IP Address are marked)
Here is the thing, I need configure a new WLAN (Pruebas) for add to 34 APs (Local and Foreign) but this new WLAN must be receive IP from a New Microsoft DHCP
Firstly I configured a new Physical interface and linked to New WLAN (Pruebas) however i don't know how configure the AP and the DHCP because I want that the AP deliver IP addresses depending the Locality.The last because the SuperScope from DHCP is divided in various subnets and because the IP from the AP will be in another VLAN
Clarify some points with capwap implementation, does all data and control traffic tunneled back to the controller and switching packets to the specific vlan will be done by the controller? so if i have 5508 controller, its maximum throughput will be 8 gbps (local mode AP), provided i have done LAG on all its ports to the LAN switch?
View 2 Replies View Relatedwhat is the reason that cisco 1130 series ap cannot be seen by switch it connected to, by CDP protocol
View 2 Replies View RelatedI've got this weird problem with my AP. It keeps rebooting randomly. It happen to all the AP in my campus randomly. It happens recently. It have been commission for quite a long time. ie user able to connect and use it. its connect back to the controller to back in another campus. Below are the logs i gather.
*Jun 7 11:13:54.287: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 7 11:13:54.290: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
[Code]......
Why it could be that switch cannot see Cisco ap 1130 series by cdp .
View 1 Replies View Relatedwe have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies View Related