Cisco Wireless :: Aironet 1250 LWAPP To Autonomous Downgrade?
Aug 25, 2010
upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies
ADVERTISEMENT
Nov 14, 2012
I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?
View 8 Replies
View Related
Jun 11, 2013
I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
View 3 Replies
View Related
Mar 13, 2013
we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies
View Related
Nov 14, 2012
When have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]
View 2 Replies
View Related
Oct 5, 2011
I have a couple of 1040N autonomous APs want to convert to light weight APs.
View 8 Replies
View Related
May 22, 2012
I need to upgrade several 1252s from autonomous to LWAPP. I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade. I wil be using NCS to do final configuration once the APs come online.
View 1 Replies
View Related
Aug 25, 2011
I would like to know AIR-AP1252AG-A-K9 (Autonomous AP) can be changed to LWAPP AP by changing IOS image??
View 1 Replies
View Related
Feb 26, 2013
I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
I'm following these commands but it is not available
debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
View 2 Replies
View Related
Sep 11, 2011
some days ago I succesfully converted AIR-LAP1041N (lwapp) to AIR-AP1041N (autonomus).I used c1140-k9w7-tar.124-25d.JA1.tar which is available to download in Download Software Section for this AP.But there are any autonomus to lightweigt firmware for this AP.I tried to use c1140-rcvk9w8-tar. 124- 21a.JA2.tar for 1140 but AP hungs after that. How can i back to LWAPP version in 1041?
View 7 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Nov 12, 2012
I have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
View 4 Replies
View Related
Feb 25, 2012
how to downgrade/upgrade AIR-LAP1142N-N-K9 access point to autonomous mode, because i don't have controller. i'm not able to login to access point as its in Leightweight mode.
View 4 Replies
View Related
Jan 6, 2011
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies
View Related
May 7, 2012
I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.
I understand that you still can run 802.11n with 2 antennas. But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nut (C)
View 3 Replies
View Related
Dec 29, 2012
I can no longer open a http or https connection to the AP. I do have ssh access and I can log in with full privileges.
I was using the Web interface a few days ago and it did something strange during an update. The display of the web page became corrupted and no longer responded to my input.
I restarted it from an ssh session and I have also power cycled it via the power injector. Neither method has worked.
What should I do next or what additional info can I provide from an ssh shell?
Physical access is very difficult. It requires a 30' ladder after 10 p.m. So, I would like to avoid that if possible.
View 7 Replies
View Related
Mar 31, 2011
I want to upgrade the ios ap-1240AG me to leave it in standalone mode.What default ip should take my ap?How should we be the tftp command to update the IOS on my ap?I am using tftp server of windows xp?
View 1 Replies
View Related
Sep 3, 2012
I have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies
View Related
Mar 8, 2011
In a multiple SSID setup, can Aironet 1240 & 1250 series AP supports different WEP key for different SSID
View 3 Replies
View Related
Jan 13, 2012
In my LAN, I have always been used an Aironet 1250 for internal use and always work fine. Now, I added a 3com AP but both AP are not correct. When I turned off the AIRONET 1250, the 3COM AP settings works fine. When both are turn on, the 3COM AP loses connectivity all the time.I have heard about the overlapping channels in 802.11b/g networks.
View 8 Replies
View Related
Jul 11, 2012
i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
View 5 Replies
View Related
Apr 22, 2012
Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies
View Related
Mar 20, 2013
Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
View 3 Replies
View Related
Mar 18, 2013
It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies
View Related
Mar 25, 2013
I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
View 5 Replies
View Related
Nov 6, 2012
The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies
View Related
Jan 27, 2013
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies
View Related
Sep 6, 2012
We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
View 7 Replies
View Related
May 13, 2013
Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies
View Related
Sep 11, 2012
I am trying to setup a Cisco Aironet 1041 on my network for WiFi authinentication and access and I do not have a Radius server and was wondering if it is possible to configure the 1041 to authenticate with just WPA or WPA2 and a PSK without any of the other configurations? This setup is only going to be temporary untill I can get the appropriate infrastructure in place to facilitate the Radius server setup I really want in 12 to 18 months from now.
View 9 Replies
View Related
Sep 16, 2012
a few day l have 3 AP Ligthweight 1250, today l was checking my infrastructure and l saw that these 3 AP can´t join to the controller, l reset the AP to the, and its can not join, l checked physicly the AP, and the Ethernet Led is in Amber permanent and the Radio Led is in Green permanet , i am searching the status led to find the fix but l have not found these convination led. and l can not access to the consolo port.
View 2 Replies
View Related
Apr 3, 2008
When using dipole antennas such as AIR-ANT 4941 with the 2.4 Ghz 1250 AP, must the antennas be spaced EXACTLY as far apart as the antenna connectors on the AP, or can the dipoles be spread further out, say to 4" spacing.
View 20 Replies
View Related
Oct 20, 2011
I've just got a new AP 1250 series, and I was trying to configure the Radio for the 2.4Ghz spectrum using the interface dot11radio 0 and I've just noticed that this controller is not present so I cannot configure it so I wonder is it could be a HW problems as it looks to me or there is another way to enable this.
I never have an issue like this before so I want to first check with you before going back to our vendor.
Here is some of the details I get from the AP itself:
System image file is "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"
ap02#sh controllers dot11Radio 0 ^% Invalid input detected at '^'
[Code].....
View 3 Replies
View Related
