Cisco :: How To Setup Autonomous WPA Access On Aironet 1041 AP
Sep 11, 2012
I am trying to setup a Cisco Aironet 1041 on my network for WiFi authinentication and access and I do not have a Radius server and was wondering if it is possible to configure the 1041 to authenticate with just WPA or WPA2 and a PSK without any of the other configurations? This setup is only going to be temporary untill I can get the appropriate infrastructure in place to facilitate the Radius server setup I really want in 12 to 18 months from now.
View 9 Replies
ADVERTISEMENT
Apr 20, 2012
Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,and also i didnt find any document with the procedure.
View 1 Replies
View Related
Nov 16, 2012
I have a Cisco Aironet 1041 , what a good repeater/wireless extender that works with it to cover an area of 50 squared meters ?
View 4 Replies
View Related
Oct 30, 2012
I have 2 SSIDs mapped to 2 VLANs (other VLANs are configured, but not used) Security is set to WPA2
What do I need to change to get higher connection speed? What is the highest for this model? Why won't it let me select 40Mhz channel width? Telnet says on 20Mhz available (GUI says it is in "Least congested" mode even though it is not)
View 5 Replies
View Related
Dec 6, 2012
I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
View 3 Replies
View Related
Oct 5, 2011
I have done a wireless site survey at a library and one AP541N will cover everything pretty well. They do have one spot where the radio strenth is not quite as strong, but you would never buy a second access point for just that one area. I did the SIte Survey using a 541N Access point.
Here is my question. I see that the Aironet 1041 is very similar in price and according to the documentation has a stronger power rating and higher antenna gain. Why would I not buy an Aironet 1041?
We are just mounting to a wall and are planning on using the pwrin4 to provide POE for whichever we buy.
View 1 Replies
View Related
Mar 4, 2012
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies
View Related
Oct 3, 2011
I am having some difficulties on finding information on how to setup two Cisco 1252 autonomous access points, via the command line. I am not having any luck finding steps on how to go about doing this and was curious if any one would be willing to give some insight. I am working on taking two of them setting one up as the root bridge and the other as non-root.
View 3 Replies
View Related
Jul 11, 2012
i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
View 5 Replies
View Related
Apr 22, 2012
Is it possible to also upgrade the 1310 series cisco ap's from autonomous to lwap without using the upgrade tool, if so what procedure do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy
View 1 Replies
View Related
Mar 20, 2013
Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
View 3 Replies
View Related
Mar 18, 2013
It`s possible configure aironet 1600 standalone without WLC and without 2 SSID? ¿What's default IP address o process to configuration?
View 3 Replies
View Related
Mar 25, 2013
I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
View 5 Replies
View Related
Nov 6, 2012
The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies
View Related
Aug 25, 2010
upgraded my home AP from Autonomous to Lwapp. I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work. I read that I need to Reload original IOS software, but It appears I cant get it without a support contract. I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1. Do I need a contract to roll back? Is there an archive (backup image) of the old IOS that could be still stored on the device. I didnt back it up and need to obtain the image.
View 5 Replies
View Related
Jan 27, 2013
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies
View Related
Sep 6, 2012
We have some Cisco Aironet 1142N Autonomous access points installed, currently running 12.4(21a)JA1 IOS system software:
System Software Filename: c1140-k9w7-tar.124-21a.JA1
System Software Version: 12.4(21a)JA1
Bootloader Version: 12.4(23c)JA3
We tried to install the following Autonomous AP IOS software update:
Release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) 30-AUG-2012
But the 15.2.2-JA system software release does not install via TFTP Web-GUI (from a accessible PumpKIN TFTP-Server poining on that software update).
What's the problem with that?Is that system software release 15.2.2-JA ED (c1140-k9w7-tar.152-2.JA.tar) not compatible to the Cisco Aironet 1142N Autonomous access points
Hardware configuration:
KurzenPartner_1#show hardware
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
[code]....
View 7 Replies
View Related
Jul 19, 2012
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
View 9 Replies
View Related
Mar 13, 2013
we have 1262 (AIR-LAP1262N-E-K9) and we dont have WLC..and i want to convert it to Autonomous mode..i did the below steps... with using this file (ap3g1-k9w7-tar.152-2.JB.tar) download it from Cisco site. Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. Step 3 Set the timeout value on the TFTP server to 30 seconds. Step 4 On the PC where the TFTP server is located, perform these steps.
View 48 Replies
View Related
May 13, 2013
Do we have Option to add MAC address of specific laptop or Mobile to connect to the Access Point in cisco Aironet AP 1260 series in Autonmous mode
View 4 Replies
View Related
Jun 11, 2013
I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
View 3 Replies
View Related
Dec 27, 2011
configure WPA2 on a 1041 access point? I am trying to get it configured through the GUI and part way through I keep getting locked out of the AP due to WPA2 being partially configured..
View 1 Replies
View Related
Apr 3, 2012
I have a wireless network using the cisco ap 1041 converted into the anonymous. however it seems like every morning or evening I have to attached it back to the SSID all over again. it will not give me an ip address. I also would have to put the encryption key in again. I am using WEP 40 bit.
View 4 Replies
View Related
Apr 25, 2013
I am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
View 1 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Jan 23, 2013
I was wondering if its possible to setup the Cisco Aironet 1260 as a WDS master with radius and another Cisco Aironet 1260 as a slave for seamless roaming. How many slaves can a WDS master handle?
View 1 Replies
View Related
Oct 21, 2011
I am trying to configure an Aironet 1142 WAP model#AIR-AP1142n-A-K9. My setup is very basic, I have a router that acts as the DHCP server, the 1142n, and a PC. I am using the 1142n in Standalone AP mode no authentication, and have it working according to the [URL]. And it is working perfectly. My questions are as follows.
1. I have isolated the wireless users from seeing each other by using ap isolation, Can I prevent the wireless users from accessing the lan pc, router and WAP configuration pages? Is there any way to do that while still maintaining internet access? Basically I just want to provide my users wireless internet access without authentication but don't want them able to see each other or anything on the lan.
View 2 Replies
View Related
Jul 10, 2012
Can the Aironet 1310 setup as a repeater? I could not make the AP as the repeater associated to another 1310 ap. This AP is running LADAP.
View 11 Replies
View Related
Sep 13, 2011
I'm new to the Cisco Aironet Access Point. I got a new STANDALONE Aironet 1260 series access point device. The part # AIR-AP1262N-A-K9. The shipping package did not come with any guide, CD, and power adapter. I searched the Cisco sites, but could not find appropriate manuals. I did find a getting started guide but not for standalone AP, it's for Controller-based AP. Question - where can I find manuals / guides to set up and configure my new standalone Cisco Aironet Access Point 1260?
View 3 Replies
View Related
May 22, 2013
I'm trying to configure a 2602i and I know there is a way to access the web GUI to accomplish this but I'm unsure if I have to access CLI to assign the AP and IP or if it already has a default IP?If it has an default IP
View 6 Replies
View Related
Apr 2, 2013
I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations. The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
I tested the WLC at our main office with a single AP, and it worked fine. The AP set itself up, and wireless devices connect with no probs. Great! Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too. Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
This morning however I've had notification that wifi performance at the remote site isn't great. I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is. Obvioulsy this is not ideal!
(I guess I HAVE done something wrong!?). And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
View 3 Replies
View Related
Jan 27, 2013
I have a Cisco Aironet 1240AG Access Point and I am trying to setup a guest network that is secure and limited in bandwidth utilization. I see an option under security > SSID Manager on the web interface to select an interface of Radio0-802.11G, Radio1-802.11A or both. Can I put the guest network on the Radio1-802.11A and make it more secure/bandwidth limited or does this option not matter?
View 3 Replies
View Related
Nov 1, 2011
I have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.
On CLI console i am seeing repeated constantly such entries:
*Mar 1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
[Code].....
( i have new firmware but how to upload it without this interface running ? )
View 16 Replies
View Related
