Cisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
ADVERTISEMENT
Jul 11, 2012
Hardware: Cisco 3750 switch and Cisco autonomous access point (AIR-AP1142N-E-K9).Requirement: A single broadcast SSID; use dot1x to assign vlan 98 to authenticated clients (computer certificate); assign vlan 3 (guest) if the authentication fails.I can achieve assigning a guest vlan on authentication failure when using a wired connection by using the following command on the interface:authentication event fail action authorize vlan 3 I'm after a way to achieve the above using the wireless access point. The main point is that internal users cannot access vlan 3 as they have a valid certificate and that guests do not have to authenticate.
View 2 Replies
View Related
Jul 24, 2012
I have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
View 2 Replies
View Related
Jan 9, 2013
Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies
View Related
Jan 17, 2013
I have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies
View Related
Jun 9, 2011
My network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies
View Related
Jan 10, 2013
we have a couple of AP1262N-E-K9 access point with firmware version 12.4(25d)JA1 operating in autonmous mode.
I attempted to measure the signal quality between the APs by setting one device to repeater mode while all others are in root mode. Then, I execute the following command: dot11 Dot11Radio 0 antenna-alignment
1. The output of "show dot11 antenna-alignment" is incorrect, the % value represents the signal strength in dBm without the - (minus). E.g. "-25 dBm" is displayed as "Signal 25% 0 dBm".Now, I know that is only a display error but still this is not clean. Is this a known issue?
2. Why are the measured signal strength values not displayed on the SSH console during the antenna-alignment test? Is it obligatory to use the console to see these values? Or is it also a known bug which might be fixed in later firmware versions?
View 2 Replies
View Related
Sep 13, 2011
download an autonomous image for Cisco Access point 1242 ?
View 1 Replies
View Related
Feb 14, 2012
We have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read in articles like create new vlan for Guest account & assign it like that , but not clear.
View 7 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Mar 23, 2010
I recently picked up a 655 with hardware version A2 and flashed to the latest firmware. I have a HotBrick router. I only want to use the 655 as an access point AND especially to use the Guest Access or Guest Zone feature to allow visitors to bring their laptops and not virus up my network. My home network is open among a few computers for things like SageTV, file serving, etc.I can get the 655 to function just fine as a standard access point by following the instructions to turn off UPNP, DHCP, etc. as outlined in the manual. I then enable the Guest Access/Zone feature, and of course give it a different SSID name, make sure it's on 24 hours a day, that it is enabled, etc.
But, none of my computers can access the internet via the Guest Account feature, just the regular wireless portion. They show connecting to the Guest Account name, etc. but no internet. I've disabled every security feature I know of to test this. Again, the "regular" WAP tests great, but no Guest Account, which is really important and one of the main reasons I bought the unit.I'm wondering - does the Guest Account feature only work if the 655 is the main router, has DHCP enabled, etc.? Does it have to be the one and only router? If so, I'm in trouble, because I can't really give up my HotBrick due to failover features, etc.
View 5 Replies
View Related
Jan 26, 2013
I have a 2960 SI lan lite switch that I am configuring for admin and guest access. I have wireless AP's plugged into trunked ports 2 and 3. I am using two vlan's (in addition to the native VLAN). Vlan 5 for Admin and Vlan 10 for guest access. I have ACL configured on the router preventing guest users from accessing the Admin network. I want to prevent those on the guest network from seeing other hosts in the vlan however the lan lite software does not support port ACL's. Any way to accomplish this with this switch.
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
View 5 Replies
View Related
Dec 13, 2012
Here is my setup:
Netgear WNDR3700 - Main router, DHCP turned on
4x Netgear WNR2000 - Setup as Access Points (DHCP turned off), connected to main router via LAN ports
I only want the guest network to have internet access. I have the guest network enabled on the router and access points with the option to "Allow Guest network to access main network" disabled. My problem is that since the access points aren't hooked directly to my modem via the WAN port, the guest network broadcasted from the access points does not have internet access.I have read up on setting up a separate subnet for the guest network using DD-WRT but was curious if there was a way to get the desired result with the stock Netgear firmware.
View 9 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jun 22, 2012
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies
View Related
Oct 28, 2011
I am running a 5508 WLC with 10 Access Point. we need to allow Internet Access to Guest. 10MB DSL Internet is dedicated for Guest. This link is terminated on a regular ADSL modem without being part of our network. We want all Guest Internet traffic to reach the ADSL Router. where should I create the Guest VLAN / where the DHCP for Guest users should be created. what is the best practise for similar setup.
Our Network is simple
ISP_Reuter-------ASA_Firewall--------------4505------------LAN-switch 2950
ADSL_modem------------ users connect via wireless but restricted to certain area only.
View 9 Replies
View Related
Apr 22, 2013
I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies
View Related
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Apr 8, 2013
Any issue creating a guest vlan to use the WIFI on an 891W router? The IOS is version 15.1. I have created discreet Vlan's and setup subinterfaces on both the WLAN_AP0 and GigaEthernet 0 interfaces with dot1q encapsulation. The client will receive an IP from the pool but cannot ping or connect beyond the default gateway.
The external interface is using Nat overload and all wired clients are successful in connecting to outside addresses. I have insert a permit any statement in the acl which affects the external port but still no success.
View 7 Replies
View Related
Feb 26, 2012
I need to configure a network in 1 small office space that segregates 2 company domains but allows them to share an Internet connection, a WAP, a couple of printers, and a non-Cisco VoIP phone system. And, it needs to provide guest access to the internet and printers via wireless. I have a SG300-28P, an SA520W, and a WAP2000 to make it all happen. [code]
View 3 Replies
View Related
Jul 3, 2012
I want to set up internet guest access with my wap321. No matter what I do the guest can see my whole network. Not sure what your definition of guest access is but letting them brows around my assets is not mine. I have a cheap Linksys router at home and that guest access works the way I want this AP to do.No wizards for guest access... In fact there is only one wizard by the way, i.e. basic set up.
My network includes the wap321, sg200-26p switch and the rv042g router
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Mar 12, 2012
I have a modem connected to a router wirelessly and an access point few computers have access to the internet and some has limited access even those close to the access point.
View 2 Replies
View Related
Jul 8, 2011
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies
View Related
May 6, 2013
I have setup an aironet 1262 with my ASA 5512 and configured it as an access point. I would like to add an additonal network to the ap for guests to use but I would like to segregate the traffic and only allow it to the internet. I am not sure how to start this and go about setting the routes, security and address scope.
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
