Cisco Wireless :: 1130 Information For Guest Wi-Fi For Stand Alone Access Point
Feb 14, 2012
We have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read in articles like create new vlan for Guest account & assign it like that , but not clear.
View 7 Replies
ADVERTISEMENT
Oct 14, 2012
IOS of my access point 1130 was deleted after bad manipulation. I have just a boot but not a flash on my AP. I can connect it just in console mode. What is the procedure to restore the IOS?
View 2 Replies
View Related
Aug 28, 2012
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies
View Related
Nov 16, 2011
we have 2 Access point WAP610N. The after some time goes in stand by and we doesn't able to connect to it. We updated at last firmware (1.0.02 build 3, Feb 25, 2011 ) Timeout inactivity 3600 Renewal key 600 Protection WPA2-PERSONAL
View 1 Replies
View Related
Jun 12, 2011
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
View 0 Replies
View Related
Feb 14, 2012
I have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
how to make this work.
View 6 Replies
View Related
Nov 15, 2011
I need Some information for Connecting my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
View 38 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Oct 3, 2011
I have a Cisco 870 integrated service router and 3 Cisco Aeronet 1180 Access Points.I have configured the router to act as a DHCP server. with all four /26 subnets in a seperate address pool.the first one is for the routers wireless interface and works fine.but the other 3 are for each of the wireless access points, that are used for internet access, but have to operate independently (i.e. the clients on each must not be able to access anything other than the devices associated with that access point and the internet.
The problem I are having is that the router doesnt distribute DHCP information via the access points so the clients on all the access points are not recieving any internet connection at all, but are connecting to the access points, and the LED for the access points suggest that they are connected t the router, the router accnowledges their existence but is not transmitting through the fast ethernet switch ports. but is communicating with a wired printer that is associated with the wireless vlan.
Each access point is on its own vlan, and the switchport access vlan command has been used. only the five static addresses have been excluded from the address pool. the router, the three access points and the printer adresses are static. the printer is working despite being the only device on the /24 network all other addresses are on the /26 networks. this to my knowledge shouldent work but it does, which is handy because the printer software doent support subnetting.The simulation I have ran say that only the printer shouldent work, but its the access points that are not working how they should. I have studied the configuration of the router and access points, and came up empty on why they are not recieving DHCP information.
I are not even able to telnet to them, despite having an address setup. I have not set up a routing protool on the router due to it being the only router. I have checked the interfaces fa0 to fa3 and they are line up protocol up, the wireless is line up protcol up, the vlans are line up protocol down, except the one asociated with the wireless which is line up protocol up (I believe the protocol only goes up when a device is connected to it).
View 9 Replies
View Related
Jul 11, 2012
Hardware: Cisco 3750 switch and Cisco autonomous access point (AIR-AP1142N-E-K9).Requirement: A single broadcast SSID; use dot1x to assign vlan 98 to authenticated clients (computer certificate); assign vlan 3 (guest) if the authentication fails.I can achieve assigning a guest vlan on authentication failure when using a wired connection by using the following command on the interface:authentication event fail action authorize vlan 3 I'm after a way to achieve the above using the wireless access point. The main point is that internal users cannot access vlan 3 as they have a valid certificate and that guests do not have to authenticate.
View 2 Replies
View Related
Jan 9, 2013
Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies
View Related
Jan 17, 2013
I have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies
View Related
Jun 9, 2011
My network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies
View Related
May 12, 2012
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies
View Related
Mar 23, 2010
I recently picked up a 655 with hardware version A2 and flashed to the latest firmware. I have a HotBrick router. I only want to use the 655 as an access point AND especially to use the Guest Access or Guest Zone feature to allow visitors to bring their laptops and not virus up my network. My home network is open among a few computers for things like SageTV, file serving, etc.I can get the 655 to function just fine as a standard access point by following the instructions to turn off UPNP, DHCP, etc. as outlined in the manual. I then enable the Guest Access/Zone feature, and of course give it a different SSID name, make sure it's on 24 hours a day, that it is enabled, etc.
But, none of my computers can access the internet via the Guest Account feature, just the regular wireless portion. They show connecting to the Guest Account name, etc. but no internet. I've disabled every security feature I know of to test this. Again, the "regular" WAP tests great, but no Guest Account, which is really important and one of the main reasons I bought the unit.I'm wondering - does the Guest Account feature only work if the 655 is the main router, has DHCP enabled, etc.? Does it have to be the one and only router? If so, I'm in trouble, because I can't really give up my HotBrick due to failover features, etc.
View 5 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Jul 24, 2012
I have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
View 2 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Mar 17, 2010
We recently acquired a 4404 Cisco controller for our network and have been adding our 1200 and 1130 Access points to the controller.This was accomplished by upgrading the APs to LWAPP and then they would automatically be discovered by the controller and then join. Lately, new 1131 APs that have undergone the same process, are not joining the controller. They are discovered but then the close the connection. We are running a flat network so all devices are in the same subnet.Software Version of the controller 6.0.188.0. [code]
View 5 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Mar 14, 2013
I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies
View Related
Jul 19, 2012
I recently bought 6 airo net 1041N standalone access points for a customer of mine. It's an academy of barely 200 students. I'll be installing an access point in every room, to ensure better signal, since they use video for there classes. The reason why i decided to install an access point in every room is because the walls are armed concrete and they had a terrible experience with a past company in which they spend a lot of money for a antenna system that didn't work.These access points will be connected to a switch, which I have to buy also.Every student is going to bring there own laptops in order to connect to the network.
The reason why I'm writing is because I have a few questions to clarify.
1) What is the best position for better signal, top side wall or corner ceiling?
2) How many client mac address filtering can i do per access point?
3)I plan on doing ESSID but can I mac filter clients to a particular access point or should I mac address filter all permitted devices in all access points. The problem is that students come with iPods and phones and as you know on windows they will be able to see the wpa2 key and enter it on the particular UN-authorized device.
4) Any graphic user interface for configuring these access points or do i have to use Cisco IOS(kind of familiar with it)? (I'm used to GUI)
5)How can I configure these access points, through Ethernet browser or do I have to use console port cable?
6)Do I have to use POE injector or can I connect the access points directly to the switch with PoE and QoS?
7)I was planning on buying a small business switch sg100 d-8 but they recommended me that I should use the catalyst 2960 series, which would be best for handling video data? don't have to be much features, just QoS.
8) Can CCp software be used in these access points?
View 9 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Sep 12, 2012
I am trying to configure this newly purchased AP to be used for WiFi surveys, heatmaps, etc..
I cant seem to get to the web interface of the AP to make config changes, even though it is picking up an IP via DHCP and it is pingable.
View 2 Replies
View Related
May 10, 2012
I have a customer with several older Aironet 1121G WAP's. In one area of the plant the noise levels from several large motors is preventing reliable connection to the WAP, even though it is located in the same conference room as the users. I am suggesting upgrading the 1121G to the 3502I to take advantage of the Clean Air technology. This raises two questions:
1) Will a single 3502I be able to effectively handle the RF noise, or does it require a network of WAPs to function properly?
2) Does the 3502I require the CT2504 controller for the Clean Air to work, or will it function in a stand alone mode?
View 8 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Apr 8, 2012
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies
View Related
