IOS of my access point 1130 was deleted after bad manipulation. I have just a boot but not a flash on my AP. I can connect it just in console mode. What is the procedure to restore the IOS?
View 2 Replies
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies View RelatedWe have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read in articles like create new vlan for Guest account & assign it like that , but not clear.
View 7 Replies View RelatedI have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
I have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
how to make this work.
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedWe recently acquired a 4404 Cisco controller for our network and have been adding our 1200 and 1130 Access points to the controller.This was accomplished by upgrading the APs to LWAPP and then they would automatically be discovered by the controller and then join. Lately, new 1131 APs that have undergone the same process, are not joining the controller. They are discovered but then the close the connection. We are running a flat network so all devices are in the same subnet.Software Version of the controller 6.0.188.0. [code]
View 5 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller. If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points? Can these access points works with LWAPP or do i need to configure CAPWAP?
View 4 Replies View RelatedI accidentally deleted the network protection key from my laptop and now can't access the internet. I have tried re-entering it but still can't connect to the internet.
View 10 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
I know what the problemis i need to tell the AP what the mac of the switchport is but i can not figure it out because it is a CATos Switch?on a IOS I would just use the Show interface command and use the bia but i dont know how to figure out the bia on a CATos?
View 3 Replies View Relatedwhat is the reason that cisco 1130 series ap cannot be seen by switch it connected to, by CDP protocol
View 2 Replies View RelatedI've got this weird problem with my AP. It keeps rebooting randomly. It happen to all the AP in my campus randomly. It happens recently. It have been commission for quite a long time. ie user able to connect and use it. its connect back to the controller to back in another campus. Below are the logs i gather.
*Jun 7 11:13:54.287: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 7 11:13:54.290: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
[Code]......
Why it could be that switch cannot see Cisco ap 1130 series by cdp .
View 1 Replies View Relatedhave netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View RelatedWe have 5 computers, 2 ipads, 3 iphones. All have been able to use the router until recently. We had a virus in our computer that is hooked up to the router. We formally had a "Linksys" router, now we have "Cisco Linksys e2500" . I had not made the connection that Linksys and Cisco were the same. We had "linksys" deleted from our "program". Some of our devices still receive wifi, so are struggling. Is there a way to down load what I need to do to get the Cisco Linksys e2500 working up to capacity?
View 1 Replies View RelatedAny info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies View Related
