Cisco Switching/Routing :: 1130 / Access Point Not Working?
Feb 14, 2012
I have a 1130 cisco access point,we are using this for wireless cisco IP phone connectivity to the network.Earlier access point was woring fine and we were able to make calls through IP phone.But we have relocated to new place.Now the access point is not working and we are not able to make the calls on the wireless IP phone as the access point is not working.But the access is in the netwrok and we are able to ping the IP address of the Access point.
We are contonuously getting the below loggs on Access point and the access point is getting power from the ethernet port of the switch not through the external powerr adaptor.
error message:
: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
4507R (0012.7fb6.6e6c).
how to make this work.
View 6 Replies
ADVERTISEMENT
Oct 14, 2012
IOS of my access point 1130 was deleted after bad manipulation. I have just a boot but not a flash on my AP. I can connect it just in console mode. What is the procedure to restore the IOS?
View 2 Replies
View Related
Jun 12, 2011
I have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
View 0 Replies
View Related
Aug 28, 2012
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies
View Related
Feb 14, 2012
We have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read in articles like create new vlan for Guest account & assign it like that , but not clear.
View 7 Replies
View Related
Apr 25, 2012
I have an 871w set up to add wireless connectivity to an existing network. When adding a client to the physical interfaces to test VLAN internet connectivity, however, a DHCP address is assigned but internet traffic on the terminal never reaches the network nor does the network recognize the IP the terminal shows as being 'connected'. Also, pings sourced from the VLAN do reach destinations. I've attached my config file, I think it's a routing issue of some kind.
10.26.99.0 is the existing network. 10.26.99.1 is an existing 871w router set as the DHCP server for that network and 10.26.99.10 is a Windows Server 2003 DNS box. VLAN 2 and DHCP pool alpha were control sets for trialing DNS settings.
View 10 Replies
View Related
May 12, 2012
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies
View Related
Jun 10, 2012
On a small Bording School we have the students living in several small houses, each equipped with an AP.Each Ap serve 4 Vlans.I want to restrict the switch for these AP, in a way to keep the students from removing the AP and connecting their own equipment.I tried using the secure port feature on the SG300, but that had the result of allowing the AP but denying all the users connected to the AP.The switch is a SG300-28P placed in L3 mode.
View 3 Replies
View Related
May 22, 2013
I have Cisco Access point AIR-CAP1602I-N-K9 ,My doubt is,is this AP support on WLC AIR-WLC2112-K9
View 1 Replies
View Related
Apr 3, 2012
i am trying to configure my HP 420 access point. I have configure different SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.
in the following the output of show run int in cisco 4500 switch:
interface GigabitEthernet3/13
description ==== HP ACCess point ====
switchport trunk allowed vlan 99,130,132
switchport mode trunk
[code]....
View 1 Replies
View Related
Jun 25, 2012
I can't figure out how to get the config right for the 802.11n channel to work.
View 4 Replies
View Related
Jan 27, 2013
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 13 Replies
View Related
Oct 27, 2011
I've just been testing QOS on 3560 with version 15.0(1) and it seems the the default qos trust behavior on access ports has changed. By default the trust state of a port is not to trust anything, however rather than rewriting the DSCP value of the incoming packets and settign it to 0 the switch now seems to leave the DSCP value unchanged.
SW04-C3560(config)# do sh mls qos int g0/2
GigabitEthernet0/2
trust state: not trusted
trust mode: not trusted
trust enabled flag: ena
[Code]......
View 4 Replies
View Related
Mar 28, 2013
I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace)
I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.
View 12 Replies
View Related
May 1, 2013
1) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
View 3 Replies
View Related
Feb 15, 2012
I have 2 data centers miles apart. They are on a Paetec MPLS. I have a Lightower point to point Ethernet link between the two data centers as well. At data center A, I have a Paetec managed router (192.168.2.1). The subnets behind that router are 192.168.2.0, 192.168.100.0 and 192.168.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 192.168.2.250 and fa1 as 10.5.5.1. Fa1 is the one end of the point to point Ethernet link to data center B.At data center B, I have a Paetec managed router (10.0.2.1). The subnets behind that router are 10.0.2.0, 10.0.100.0 and 10.0.101.0. I also have a Cisco 1841 that is configured with fa0 addressed as 10.0.2.250 and fa1 as 10.5.5.2.What I want to happen is any traffic headed from data center A destined for 10.0.100.0 or 10.0.101.0 to be routed through the point to point Ethernet link. I had Paetec add routes in their managed router to route any traffic headed for 10.0.100.0 and 10.0.101.0 to my Cisco 1841 (192.168.2.250).I wanted to do the same for traffic destined for 192.168.100.0 and 192.168.101.0 from data center B. Paetec added the appropriate routes to the router at data center B.Now, if I trace from data center A to 10.0.100.45, I see this:
1 <1 ms <1 ms <1 ms 192.168.2.1
2 <1 ms <1 ms <1 ms 192.168.2.250
3 4 ms 4 ms 4 ms 10.5.5.2
4 3 ms 3 ms 3 ms 10.0.2.1
So the routing seems to be ok. However after it hits 10.0.2.1, it gets lost after that.Am I missing something? Is this a misconfiguration on Paetec’s routers?
View 1 Replies
View Related
Jul 30, 2012
I am facing issue with http login after IOS upgrade on 3750 switches. I upgrade IOS from c3750-ipbase-mz.122-35.SE5.bin to c3750-ipbase-mz.122-53.SE2. bin Any other command I have to run.
View 1 Replies
View Related
Sep 5, 2012
Extended IP access list VLAN20
10 permit tcp any any established
11 permit icmp any any
20 permit tcp any 192.168.20.0 0.0.0.255 eq 80
30 permit tcp any 192.168.20.0 0.0.0.255 eq 443
40 deny ip any any log
[code].....
Above is the network diagram and access list for VLAN 20 and VLAN 30, applied on incoming direction of each valn.But still able to access other port which is not on access list, tried changing the direction with no luck.Inter vlan routing is enabled on CoreSwitch default router is 192.168.10.10
View 5 Replies
View Related
Feb 27, 2013
I work in a small office/production building and lately we have been having problems with an unstable connection. We are using a Meraki MR24 access point in our warehouse, the connection always starts out strong but sooner or later everyone will briefly lose connection and the AP goes away, then comes back and we're reconnected at excellent connection again.
View 3 Replies
View Related
Mar 15, 2012
I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
View 0 Replies
View Related
Sep 11, 2012
recently i just connected a non cisco ip phone(from panasonic) to Cisco 2960 POE switch at site A. The PABX system is located at site B,Site A and site B are connected using MetroE Point to point.I would like to apply QoS for voice vlan. I want to assign 2MB to the point to point connection for voice vlan.
View 3 Replies
View Related
Dec 7, 2012
i have the topology :=========want to mention that im using port address translation on the router & not sure if it is making a conflict .
here is the config below :
why the cache is not working ?i mean that i tried going to internet with source ips of the subnet 10.20.30 , but i seems went to internet without any precedence of cahce server
[code]...
View 1 Replies
View Related
Sep 20, 2011
We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.
View 2 Replies
View Related
Jul 13, 2011
I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
View 1 Replies
View Related
Jan 17, 2013
i access points in our network.I want to connect with 3550 switch but access point is not working and getting the below error
controller port error.
IOS image --=c3550-i9q3l2-mz.121-20.EA1a.bin
Switch Model---WS-C3550-24PWR-SMI
I want to know ,this access point is supported on this switch ?
View 17 Replies
View Related
Nov 23, 2011
Not sure why the N7K M1 card doesn't take this command. It works on other N7K at different site. [code]
View 1 Replies
View Related
Sep 15, 2012
I had a strange issue with one of my customer..Cisco WS-C3750X-48P Access switch was not reachable and after reload it started working.I would like to know the root cause of the issue. There were no logs and no errors in interfaces.Even Cpu utilization was not high. We have enabled arp inspection and dhcp snooping in the switch..Hope this will not make any issue..Also we have dot1x enabled on port..
View 5 Replies
View Related
Mar 31, 2012
Powerline not working on media in one room. My Setup: ATT DSL Modem: Westell 6500 w/ Linksys WRT54GS router
First powerline to mac (about 8 feet down hall) second powerline to pc (windows vista) (about 12 feet down hall) third powerline to media (Xbox 360, Sony blu ray, Apple TV) (about 45 feet down hall)
I've had Powerline PLE/S 300 setup for a couple years I think working perfectly. I it set up because my house is VERY solidly built and the G wireless cannot reach even the second room down the hall.
I recently got a wireless device and couldn't keep connection in the living room so I was going to add an access point and futzed with the router and everything went down. I got the router back up, disconnected the access point for good, but the Powerlines wouldn't connect. I upgraded the firmware then reset them and finally got Number 1 and Number two powerline online and working. But the farthest point (router at back of house, media at front) is the living room and none of the powerline boxes will work ON THE MEDIA.
I plug in the powerline and the home light comes up, I attached my laptop out there and I connected fine, then I connect one of the media players - the Xbox, apple or blue ray - and the home light goes out media will not connect and the laptop is knocked off. It does this every time now, same media players that worked perfectly before.
I bought a new router (Linksys E4200), wondering if the old just didn't have the signal strength and set that up very easily and the same thing happened - no powerlines work on the media in the living room. Mind you, I did take Apple to a closer room and hook it up to a powerline and it works!
As my Xbox died on one my attempts to plug it in to the powerline. So new xbox cannot connect either. I used to connect from xbox to the pc media center to watch recorded tv and this cannot be done wirelessly, even with the new dual band N router AND a new extender!
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
